Question about HP PC Desktops

1 Answer

Dim screen hp nx9110 - HP PC Desktops

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 34 Answers

Hold down "FN" button (Right of the right-CTRL button) and press F8 for brigher and F7 for dimmer.

Posted on Jul 08, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What's your problem?the screen turns very dim to where you can barely see the picture


Your monitor is going bad or your video card is going bad. Try using another monitor on the computer to isolate the problem. Borrow a monitor from a neighbor, friend, relative or co-worker and see if you can barely see the icons and desktop on it. If the borrowed monitor is bright and clear and you can see things ok, then your original monitor is going bad. If the borrowed monitor shows the same problem of barely being able to see things, then your video card in the computer is bad.

May 06, 2012 | HP Pavilion Slimline s3600t Desktop PC

1 Answer

Screen does not show picture just very dim


is this a flat panel monitor? If so it is likely to be eithe rthe back light or the invertor. Invertors are relativly cheap if you can find one - try bitsnpcs.co.uk but if it is a screen gicve up as uneconomical usually.
Good luck

Jul 11, 2010 | HP Pavilion a1610n (882780664463) PC...

1 Answer

On startup, goes to very dim screen


If the hard drive is going bad, usually running scan disk will help diagnose the problem. If scan disk reports bad sectors then it is likely time to replace the drive. If no bad sectors then the problem is probably somewhere else. Hopefully it is functional enough to get to scan disk.
left double click on my computer, right click on the C: drive, click properties, choose the tools tab, then choose "error checking"

Aug 09, 2009 | HP Pavilion a320n PC Desktop

2 Answers

I have a HP Pavilion laptop ze4900. Every time I move th screen, the display either goes off completely, or it goes vey dim and I cannot read anything from it. The only thing I can do to get a display


You could have a defective screen - a defective inverter or a CCFL lamp.
To determine if you have a LCD screen or video card problem, read this and follow the instructions.

Defective CCFL backlight, it may have the following symptom:

  • Screen flashs on red/pink and off.
  • Picture stays on in red and slowly be come normal.
  • Picture flickering with dim display.
  • Picture flickering on and off.
All these symptoms indicate that the LCD backlight lamp (CCFL Lamp) has reached the end of the life and all you need to do is replacing the CCFL lamp

Connect an external monitor to your laptop and power it up, if you see the normal Windows images then the video card and laptop is OK and the problem is definitely the backlight.

Dim image and/or dark display on the laptop's LCD screen indicates a faulty LCD backlight and it could be the inverter that supplies high voltage to the CCFL lamp or it is the CCLF lamp is nearly burnt out or burnt out, most likely this is the case.
The inverter can be replaced easily but the CCLF lamp is more time consuming and requires soldering skills.
Check out www.lcdparts.net for parts, repair service and DIY info.

May 03, 2009 | PC Desktops

1 Answer

Corrupted DMI Strings in BIOS


May be the bios chip on the mother board defective.Plse contact a technician who is doing chiplevel servicing mother board

May 01, 2009 | PC Desktops

1 Answer

Hi there, I have an hp compaq nx9110. I have used this to burn my photo's onto CD. I can however not read the cd's written on teh nx9110 on any other computer - not even DOS on the other machines sees the...


Try using (Ashampoo Burning Studio 6 FREE) this link below for all your burning needs .Also make sure to burn your photo's as data. This has work in all 4 of my computers & should be readable on all computer or laptops!
http://www.download.com/Ashampoo-Burning-Studio-Free/3000-2646_4-10776287.html

Dec 20, 2008 | PC Desktops

1 Answer

Backlight only stays on for a few seconds on compaq c700 that is only a year old


When the external AC power supply is unplugged from a notebook, the LCD display will dim to conserve on battery power. During times of heavy battery power operation; such as during the startup or boot process, the display may be very dim or barely readable. If the display remains dim when the notebook is operating on the Windows desktop, follow the steps below to resolve problems with display brightness Restart the notebook with AC power Follow the steps below to determine if the dim display is due to a hardware failure:
  1. Connect the AC adapter to the notebook and a working electrical outlet.
  2. Power down the notebook PC by pressing and holding the power button for 5 seconds.
  3. Press the power button again to start the computer.
If the display is still dim after restarting with the AC adapter connected, try changing the LCD brightness. Adjust the LCD brightness using the function keys From the Windows desktop, hold the fn key and press the f7 key c00776226.jpg to increase or the f8 key c00776225.jpg to decrease the brightness of the display. If using the function keys does not resolve the problem and you have a Lid Actuator on your particular model, check the movement of the Lid Actuator switch to determine that it moves freely and is not stuck. NOTE: The key numbers ( f7 or f8 ) may vary depending on the notebook PC; however, the images on the keys should be familiar. Check the movement of the Lid Actuator switch The Lid Actuator switch is available on some models. It is a small button or switch located above the keyboard near the hinge for the LCD. Pressing this switch when the computer is on may turn the notebook display off, or it may cause the notebook to enter a different power state. Press the switch two to three times while observing the display. If the display does not return to normal brightness when the switch is released, the switch may be sticking and need to be repaired. Contact HP service and support for further assistance. If the display turns off when the switch is pressed, the power management function may be set to hibernate or turn off when the lid is closed. Install updated BIOS and drivers To resolve certain hardware and software issues, use HP Health Check to automatically search the HP web site for an updated BIOS as well as any updated software and drivers. To launch HP Health Check, follow the steps below.
  1. Click Start , type health into the search field, and then select HP Health Check from the list. HP Health Check displays a list of available BIOS, software, and driver updates for your particular model.
  2. Click the description link for any BIOS, software, or driver updates, and then follow the on-screen instructions. You can only install one update at a time.
  3. Repeat steps 1 and 2 above for all updates that you want to install.
You have now installed the available BIOS, software, and driver updates for your particular computer model. Contact HP service and support If the display remains dim after doing the troubleshooting steps listed in this document, contact HP service and support for further assistance.

Oct 15, 2008 | PC Desktops

1 Answer

The screen dim when computer start up hp pavilion dv4 1020us notebook


A dim or dark screen does not necessarily mean a bad inverter! It could be a faulty lcd backlight bulb, inverter cable, inverter, or in some cases a motherboard failure.

Aug 18, 2008 | PC Desktops

1 Answer

HP compaq nx9110 has a very very dull screen when running on electricity. When you run it on battery it is perfect. However battery last for seconds and cuts out.Obviously the battery needs replacing....


You'll have to replace the battery, of course...but for fixing the screen thing...you'll have to see if the powersource has the exact parameters that are writen on it...like for example I had the same problem with a fujitsu...and the actual charger, or powersource was having a lower output that the one writen on it...it was a 14 Volt, and 2 Amper, that was writen, but it only had 12 Volts and 1.3 Ampers at the output, when I measured it...so...I had to replace a 4.7 Ohm resistor, right at the exiting points, and it got fixed, so what I mean to say that after replacing the battery, you really have to check the powersource for any errors and see if the output is identical to the one writen on it...please tell me if I was right.

Jul 24, 2008 | PC Desktops

1 Answer

Dim screen ph nx9110


good morning sir,,

now u have to find a button in ur keybord which has symbol of sun and a + beside it. do press the specified button to access the button(function btn,shift btn) nad te brightness button,

another method is :
right click in desktop- goto properties - clik setting - adjust the gamma settings

fixed by fixya

Jul 08, 2008 | HP PC Desktops

Not finding what you are looking for?
PC Desktops Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP PC Desktops Experts

Fred Sops

Level 2 Expert

271 Answers

john smith

Level 2 Expert

366 Answers

Gavindu Dileepa

Level 1 Expert

10 Answers

Are you a HP PC Desktop Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...