Does the HDMI works as an input? - Acer Aspire 6930-6455 Notebook PC

how do you set up the HDMI input on a hitachi tv model #51F59A ...

https://answers.yahoo.com/question/index?qid...

Jan 8, 2010 - i tried to hook up an HDMI devise but i cant set it on input HDMI it ... My TV has HDMI, Component and AV inputs, which one should i use for my ...

HDMI not working - Hitachi 50VS69A - AVS Forum ' Home Theater ...

www.avsforum.com/.../948284-hdmi-not-working-hitachi-50vs69a.html

Dec 1, 2007 - 7 posts - ‎2 authors
I have a Hitachi 50VS69A 50 RP LCD HDTV connected to a Dish Network receiver that the HDMI input is not working on. I have been using the ... Hitachi P50H401 - all HDMI ports are dead - HELP!
6 posts
Oct 2, 2008
Hitachi 51/57/65F59A CRT RPTV Tweaks Thread
30 posts
Jan 19, 2007
More results from www.avsforum.com

if all 4 inputs work with another input source(i.e. your Motorola box) it indicates the issue is with the TWC input source. Also check your HDMI cable to be sure it is in good condition & properly plugged in on both ends.

I understand from your original message the main HDMI output works, and only one of the HDMI input is working. Which HDMI input is working? Bluray, Cabl/sat, or Game? Are you able to select the working HDMI input either from the remote, and front panel of the receiver, or just from input of the receiver?

Double check your settings for Audio output and HDMI controls (found on page 36 and 37) of the owner's manual.

You have to tell the TV which HDMI input to use. ie you should be able to press a button on your remote to do this. On my tv we can choose between 4 different HDMI inputs via the remote.

I'm having the same problem. The projector stopped recognizing any input over either of the two HDMI inputs. The JVC RX-D411S receiver was working fine up until I used the VGA input with a computer and since that time, HDMI has not worked (despite working fine before). I tested two HDMI cables into each of the two ports but nothing! All other inputs work fine.

Hi.

To start ensure that each time you connect or disconnect the HDMI ports both TV and connected device are off.

Also ensure that HDMI input is active, as detailed here.

HDMI connectors carry voltage, and connecting the HDMI cable while TV or device is on may easily damage the HDMI port, making it unusable.

The HDMI 3 and Component 3 are separate input. The component input may work, and HDMI port may still be defective.

To test the port do the following:

Disconnect TV power cord, and connected device (eg. Receiver, DVD etc.).
Leave units disconnected for five minutes.

While power is disconnected, test connecting on port three a device that was previously working on HDMI 1. Also use a cable that you know is working.

Connect back power with HDMI cable already connected. If HDMI 3 is still not detected, then the port is defective.

In that case ring Pioneer at the number listed on the owners manual.This model is often advertised as only two HDMI inputs. Call Pioneer to ensure the third port can be enabled.

This receiver has only one HDMI output, but 4 HDMI inputs. If some inputs don't work, try connecting the equipment (DVD for example) to HDMI input which works with other equipment....
For the RCA (composite) video input - it won't work, because this receiver don't have any video processing circuit.
So HDMI input video goes to HDMI outout connector.
Composite (RCA) video input goes to Composite outout and no other video output.
S-video input goes only to s-video output.

why hdmi input wont show up

For me, it was the Monitor Out setting that had defaulted back to Component. I remembered to change the individual inputs to HDMI - but had forgotten to set the Monitor Out to be HDMI.

the r04u comes factory with hdmi DISABLED, hook up your hdmi device, and turn r04u to the hdmi  input (input 1 or input 3)  then:
To activate the HDMI terminal: 
1 Press HOME MENU. 
2 Press /  to select “Option”, and then press 
ENTER. 
3 Press /  to select “HDMI Input”, and then press 
ENTER. 
4 Press /  to select “Setting”, and then press 
ENTER. 
5 Press /  to select “Enable”, and then press 
ENTER.


there you go