Question about Northstar Gas Powered Wet Steam & Hot Water Pressure Washer 3000 PSI

1 Answer

Burner lights for a few seconds then goes out and wont relight mod # 1572251a

Posted by Anonymous on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 21 Answers

This could be a number of problems, first thing is replace the fuel filter

Posted on Dec 30, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

GX90-715A wont stay fired


1) Product manual has burner info page 11, maintenance 12, and troubleshoot flow charts starting page 17
Otherwise, Rheem does not post service manuals.
http://bostonheatingsupply.com/Rheem/Rheem%20Commerical%20Gas/Rheem_CommGas_Extreme_Use%20and%20Care%20Manual.pdf

2) Post question on pro water heater forum.
http://www.thetankatwaterheaterrescue.com/forums/forum3/

3) Is air intake clear? Is the burner sooted? Is the flame large and clear blue? Is the vent obstructed? Does air draft when blower activates?

Feb 14, 2013 | Rheem RUUD GX90-715A Water Heater,gas,90...

1 Answer

Weil McLain Clicks and then burners shut down


it needs a new thermal coupling ,this tell the gas valve to open if it goes bad your heater shuts off for safety reasons.

Nov 29, 2012 | Watches

1 Answer

My Kenmore gas dryer mod 110.77522600 burner light when I first turn it on. After 4 mins. or so, it goes out. It will try to relight several time (igniter glows) but it never does.


This is usually the dryer coils have failed. They tend to fail as they heat up. They are inexpensive and easy to replace. Here is a video on replacing the dryer coils. If you need further help try this link for troubleshooting a gas dryer

Jan 03, 2011 | Kenmore Dryers

1 Answer

Pilot light lights and stays lit until you turn the temp up. Burner ignites for a few seconds and then everything goes out and you have to wait about an hour to relight it


Sounds like this is the gas regulator giving the the problems, i would call a local plumber to service this . gas and flame is very dangerous.

Mar 27, 2010 | Rheem Water Heaters

1 Answer

Flame goes on than out and keeps doing that wont stay lit!!


I'm assuming you're referring to a gas burner that supplements the heat pump. If the burner lights at all, The ignition system is working. If you need to reset it for it to relight, I would suspect the thermocouple. It detects the flame to prevent gas from pouring out of an unlit burner. If it malfunctions, the control thinks the burner didn't light and shuts down for safety.

Nov 26, 2009 | Weather King 10AJA6001AH Air Conditioner

1 Answer

Sears kenmore gas dryer 417.92052101does not stay lit.


Watch the burner assembly, shortly after starting the dryer the ignitor should begin to glow. If it glows for several seconds (up to 15 seconds) and then goes out, then the problem is probably the solenoids (coils). If the ignitor glows and stays on, then the problem is usually the flame sensor.

Jul 11, 2009 | Dryers

1 Answer

Dryer will light and heat for a minute or so then goes out and wont relight again until it sits a while-


check your vent going out through the wall and be sure its not stopped up

Apr 23, 2009 | Dryers

1 Answer

Thermador model RDF30RS burners won't light


Hi, there are two small circuit boards on those burner controls. They are called potentiometers. There was probably a boil over or spill at some point. They are notorious for failing. Hope that helps.

May 04, 2017 | Kitchen Ranges

Not finding what you are looking for?
Northstar Gas Powered Wet Steam & Hot Water Pressure Washer 3000 PSI Logo

229 people viewed this question

Ask a Question

Usually answered in minutes!

Top Northstar Garden Experts

John Trevino

Level 3 Expert

1383 Answers

Brad Brown

Level 3 Expert

15557 Answers

Roland W VanLue
Roland W VanLue

Level 3 Expert

486 Answers

Are you a Northstar Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...