Question about U-Line BI-95

1 Answer

How to replace the ice maker unit.

My BI95 ice maker is not making much ice. I have replaced the thermostat. That did not help. The tem is set to around 20 deg. And i am alsogetting some of the teflon coating off of it in the ice. So i ordered a new unit. Now how does it come out. I think i have removed all of the screws but it will not come out. I also ordered a new door seal. Thanks in advance

Posted by on


1 Answer

I just RR'd mine. Undo the three screws on the bottom of the metal piece that the ice maker sits on, then the two screws that are horizontle above the . Take of the back, withdraw the termocouple from the tube that goes through the foam, clip the wires (5) leaving enough of a pigtail to crimp a **** splice to the new ones. Withdraw the fill tube. Don't lose the clay that seals the holes through the insulation. Withdraw the ice maker by gently twisting and pulling straight out. Replace in reverse order. Getting the screws back in is a little tricky.

Posted on Jul 15, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Repairman can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Repairman (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My ice maker stopped making ice. it is frozen in the tray and it won't dump it. I just replaced the filter thinking that it could be the cause because it was due to be changed. i unplugged the unit for a...

The ice maker inside the refrigerator needs to be replaced because the thermostat in the ice maker itself never makes so the ice maker always thinks it has water in it acording to the thermostat so it never attempts to dump or refill.

Sep 05, 2010 | Samsung RS2630WW Side by Side Refrigerator

1 Answer


Most likely the water control valve is the reason that your ice maker will not work. I would like you to fill the ice maker with tap water and if it dumps and does not refill then the water control valve will need replaced. tem # 153540 Water Control Valve If it is the ice maker I will help you find the replacement, Thanks, Sea Breeze

Dec 26, 2009 | Samsung RB215LASH

1 Answer


try the control bd first this is a bad problem with this model

Oct 11, 2009 | Refrigerators

1 Answer

My uline BCM45A ice maker is cold but does not make ice

This unit work on the thermostat. When the temperature gets between 10 - 15 degrees it will satisfy the control then turn the compressor off and icemaker will advance. If the control is set too cold then it will never satisfy the control. 1st make sure the thermostat is at the warmest setting. When the compressor cycles off look to see if the icemaker is advancing.If no then replace the control.

Sep 15, 2009 | U-Line Icemaker

1 Answer

Our old RV U-Line Icemaker, model 45A has stopped making ice and does not get cold. What does it need?

You need to check to see if the compressor is running and the fan is running. If both are then you need a new unit. The 45A has the r12 refrigerant in it and you wont be able to get parts for a r12 system. U-line makes a BI95 to replace that model. If the fan isnt running then I would replace the fan. If nothing is running then it could be a bad thermostat but first make sure the ejector blade on the icemaker is at the 12 oclock position.

Jul 17, 2009 | U-Line Icemaker

1 Answer

Have a bi95 water not going throught inlet valve,hose is clear to freezing tray. took valve apart did not see any obstruction. any suggestions? thanks mike55

The valve assembly for U-lines shouldnt be taken apart. Now the first thing is to advance the icemaker. Remove the cover off the icemaker head. (pry and pull at the same time) use a 5/16 nutdriver or socket on the small gear. Turn it counter clockwise. Whent he ejector blade reaches 1 or 2 oclock it should take off by itself. When the ejector blade reaches 10 oclock then it calls for water.
(ejector blade is the fingers that push the ice out)
How a bi 95 works is the thermostat need to be satisfied first. Then it advances the icemaker. Turn it to the warmest setting. If its set too cold then it would run and never be satisfied.(warmer the setting the more ice it makes) Everytime the compressor cycles off the icemaker should be advancing. If not then the thermostat could be stuck in the freeze mode.
T-stat Terminals 2 is yellow(common)
3 is blue/black (fan & compressor)
1 is red (icemaker)

2&3 closed freeze cycle
2&1 closed harvest mode

Jul 10, 2009 | U-Line Icemaker

1 Answer

Ice maker

read the mamual
U Line Origin Series BI95 14" Ice Maker with 12lbs. of Ice Storage, 23lbs. Daily Ice Production & No Drain Required "The difference is in the details. Take a closer look." Compact andconvenient, the Origins BI series offers both streamlined styling andADA compliance. As developers and manufacturer of the world's firstbuilt-in undercounter residential and light commercial ice maker,U-Line maintains its posi ... More

Sep 18, 2008 | U-Line Icemaker

1 Answer

Ice sticking

hi thanks for the question. yes i would try that Lowering the tem in freezer and in your freezer theres a setting aside from the thermostat set that in the middle to keep most of the cold air in freezer your fridge temp should still ok Thanks for the question The appliance doc

Sep 12, 2008 | Whirlpool Refrigerators

5 Answers

U-Line 95

The part number is #150 faceplate. This would be the motor and switches. Approx $55.00 Appliance parts depot would have it. Or try all brand parts.

Jun 07, 2008 | U-Line Icemaker

4 Answers

ICE MAKER NOT WORKING Kenmore cold Spot model# 106.55536400

Most common problem is a broken ice maker module.  Should also replace ice maker thermostat when changing the module.  Make sure fill tube isn't frozen first. If you take the ice maker out pull off the plastic cover and in the center of the wheel that kind of looks like a gear there are two little plastic studs.  If one is broke or they are pressed together then the module is bad. Make sure to replace the thermostat along with some silicone grease because a bad thermostat is what causes the module to break.

Oct 19, 2007 | Kenmore 55612 / 55614 / 5561 / 655619 Side...

Not finding what you are looking for?
U-Line BI-95 Logo

Related Topics:

874 people viewed this question

Ask a Question

Usually answered in minutes!

Top U-Line Kitchen Appliances - Others Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Charles T Nevin
Charles T Nevin

Level 3 Expert

4070 Answers


Level 3 Expert

2237 Answers

Are you an U-Line Kitchen Appliances - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides