Sony Blue Ray dvd player has stopped working when wired through the Onkyo receiver (works if HDMI wire is connected directly to tv). I have had the setup for 2 years and only use the dvd player a handfull of times per year.

Hello, I am sorry about your issue. Have you tried the other HDMI ports on the receiver. Please check the cable from the receiver to the TV. Thank you, Onkyo USA

You have not clarified if you have made the correct assignments of the devices to the Onkyo.

For example HDMI IN1 = BD/DVD etc.

Refer page 39 of the user manual.

onkyo receivers have a problem, see

http://www.hdtvsupply.com/hdmi-cable-booster.html

Connect HDMI cable from the rear panel of the blu ray player to the DVD/IN digital section, labeled as "HDMI/IN" on the rear panel of the receiver.

Depending on if your surround system has a hdmi input or not. if it does you can connect the blu-ray player to it. If it doesn't have an hdmi input you will have to run the hdmi cable from the blu-ray to the tv then run a set of rca cables (red and white plugs) from the tv audio out to the surround systems' audio input jacks to get sound through the surround system. Most surround systems don't have an auxiliary input for another video device.

Try hooking the Panasonic up straight to the tv without going through the receiver. If it displays a picture its obviously not the blu-ray player. May also be a problem with the HDMI cable itself. Hope this helps.

See www.avforums.com/forums/onkyo-owners-forum/696423-faq-setting-up-ps3-onkyo-amp.html

This should give you the info to set up the ps3.

insted of running it thru the tv an to the reciver try doing it directly from the DVD player to the reciver just the audio jacks

Maybe error on connection that's why no sound.Just click below for connection guide..

DVD Players/Recorders: Home Theater Setup, Installation & Hook Up ..

• Audio and Video Connection Guide
• What is HDMI Technology?
• HDMI Explained in Detail
• Audio and Video Definitions

Plasma or Video Projector Wiring Guide

Blue-ray Surround Wiring

hope this may help;


DONT FORGET TO RATE;


Regards,
VOTIT

My configuration:
ZONE 1 (living room)
DishNetwork Dual Tuner DVR Tuner 1 [S-Video out] -> [S-Video in] ONKYO TX-SR875 [HDMI out] -> [HDMI in] Sony KDS-60A3000 rear projection TV

ZONE 2 (living room)
DishNetwork Dual Tuner DVR Tuner 2 [Composite Video out] -> [Composite Video in] ONKYO TX-SR875 [Composite Video out] -> [Composite Video in] Samsung AQUOS LCD TV

Problem:
ONKYO receiver stops sending video signal to my ZONE 1 Sony TV through the HDMI connection. ZONE 2 may still receive video. (NOTE: the issue might be related to the upconverter circuitry?)

Symptom:
I couldn't see any video, but I could hear the Tuner 1 audio through my ONKYO. An important clue is that I couldn't see ONKYO's on-screen display menu on my TV when hitting the [Setup] button on my remote. But, I could see my TV's Sony-based menus and display options.

Solution:
1. Put all ZONES in Standby mode using the remote. Hit these buttons on remote: [Receiver], then [Standby]. [Receiver], [ZONE2], then [Standby], [Receiver], [ZONE3], then [Standby]. You should NOT see any lights on the ONKYO except maybe one red led near the power button.
2. Pull the power plug out of the back of the ONKYO, and leave unplugged for 20-30 seconds. Turning off any power center it is connected to isn't enough. You MUST unplug the power from the back of the ONKYO for 20-30 seconds.
3. Reconnect the power cord to the ONKYO.
4. Using the remote, set ZONE1 to a video source known to be working. If you don't see video, try leaving the power cord off for a longer period.

I know it sounds too simple to work, but that's what brought the video back for me the few times the video stopped displaying. Hope it works for you.