Question about Jamo E8 SUB Subwoofer

1 Answer

I have Jamo E8sub need to be fixed. The power LED is not on, it was RED at one time (Did not turned Green), but not anymore. I checked the DC voltage on main IC (LM3886) no power on Pin # 1 and 5. Both mosfet has no drain voltage. The Gate voltage is as equal as the saurce voltage. Both Mosfets are fine. I was wondering if I should replace the main board? How much it cost? Any sujestion? Please let me know.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jamo Master
  • 6,694 Answers

Hi,
the ic lm3886 should have voltage at its pin 1 and 5 , because it is the vdd supply pin of that ic. trace out, to where the track goes from pin 1and 5. it should go to the power supply or to any switching circuit. may be problem with its power supply side . any one of the voltage is missing. check the voltage regulators if there. check the power supply side i think complaint lies there. no need to replace the main board . from ur narration i think u have knowledge in electronics. make one more try to solve the problem.
ok

Posted on Dec 30, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sharp LC-50LE442U does not turn on. RED standby LED is lit, when I try to turn it on, the LED turns green but screen stays black. LED then stays green, won't go back to red when turning off.


You cannot tell if capacitors are bad just by looking at them. they need to have a meter called an ESR meter to test them, I can tell you with almost certainty that it is a capacitor in the power supply that has failed. The whole board is Sharp 9JY0950CTN02000 Power Supply Board (09-50CTN020-00) LC-50LE440U LC-50LE442U

May 27, 2016 | Sharp AQUOS LC-50LE442U 50" LED TV...

1 Answer

I have a reebok crosswalk rt 5.0 treadmill. I can calibrate the incline and it goes up and down. however when you press the button to raise the incline the incline number will change but the machine does...


Step 1:

see this details and proceed according. God bless you

The SCR lower board is designed with diagnostic LED lights. The LED's are color coded according to

their specific function. Green indicates a properly operating treadmill; the green lights should always

be ON when power is supplied to the treadmill. Yellow indicates a treadmill function. Red indicates a

treadmill malfunction. Here is a list of each LED and what it signifies:

MOTOR (yellow) - The MOTOR LED illuminates when dc (direct current) voltage is sent to the drive

motor. The LED gets brighter when the dc output is increased.

RLC (yellow) - The RLC (R = Reactance / L = Inductance / C = Capacitance) LED illuminates when

the filtering system is properly working. The filtering system includes the capacitor and filter choke. If

there is a short in either component then the RLC light will not come on.

DN & UP (yellow) - The DN and UP LED lights tell us if the elevation DN and UP relays are

functioning properly. When the LED lights, it tells us that the relay has energized and is sending high

voltage (110vac or 220vac) to the elevation motor.

AC PWR (green) - The AC PWR (Alternating Current Power) illuminates when AC line voltage is

delivered to the treadmill. It then passes through the in-line fuse (110)/s(220) and lights the AC PWR

LED.

+12V (green) - When the proper AC voltage is delivered to the treadmill, passes through the in-line

fuse/s, through the full wave bridge rectifier (changes AC to DC), through the transformer (steps down

Step 2:

This the board LED, who control the DC to +12vdc) then the +12V LED lights.
signal for Main Motor+Elevation Motor. You must see, the LED DN+ UP( both will be Lit) in any position down or Up.

2) The RELAY board is designed with diagnostic LED lights. The LED's are color coded according to

their specific function. Green indicates a properly operating treadmill; the green lights should always

be ON when power is supplied to the treadmill. Yellow indicates a treadmill function. Red indicates a

treadmill malfunction. Here is a list of each LED and what it signifies:

AC PWR (green) - The AC PWR (Alternating Current Power) illuminates when AC line voltage is

delivered to the treadmill. It then passes through the in-line fuse (110)/s(220) and lights the AC PWR

LED.

VDC (green) - The VDC LED will light when it receives DC voltage from the DC power supply.

DN & UP (yellow) - The DN and UP LED lights tell us if the elevation DN and UP relays are

functioning properly. When the LED lights, it tells us that the relay has energized and is sending high

voltage (110vac or 220vac) to the elevation motor.

UPSW (green) - This LED will illuminate when the low voltage dc is delivered from the upper display

board to the elevation UP relay. This low voltage dc is what energizes the coil of the relay.

DNSW (green) - This LED will illuminate when the low voltage dc is delivered from the upper display

board to the elevation DOWN relay. This low voltage dc is what energizes the coil of the relay.

BELTSW (green) - This LED will illuminate when the low voltage dc is delivered from the upper

display board to the belt (motor start) relay. This low voltage dc is what energizes the coil of the relay.

SPD (yellow) - The SPD LED flashes on and off (relative to speed) when the speed sensor is

operating properly.

PWM (yellow) - This LED will light when the upper board is sending a speed signal to the PWM.

Both the PWM LED and BELTSW LED must be lit for belt movement.
Finally this this Relay Board, the Each Led will be Lit, for any Relai control for DN down, or UP for elevation Motor. You must clean contact of the Relay with Special Spray(Radio Schack).

With this you must fix it.

Jan 07, 2013 | Reebok Exercise & Fitness

1 Answer

My new visions t9550 treadmill will not calibrate. it completes the speed calibration but treadmill will not elivate therefor fails calibration. what do i do?


Step 1:

follow this steps for troubleshooting and fix it. God bless you

The SCR lower board is designed with diagnostic LED lights. The LED's are color coded according to

their specific function. Green indicates a properly operating treadmill; the green lights should always

be ON when power is supplied to the treadmill. Yellow indicates a treadmill function. Red indicates a

treadmill malfunction. Here is a list of each LED and what it signifies:

MOTOR (yellow) - The MOTOR LED illuminates when dc (direct current) voltage is sent to the drive

motor. The LED gets brighter when the dc output is increased.

RLC (yellow) - The RLC (R = Reactance / L = Inductance / C = Capacitance) LED illuminates when

the filtering system is properly working. The filtering system includes the capacitor and filter choke. If

there is a short in either component then the RLC light will not come on.

DN & UP (yellow) - The DN and UP LED lights tell us if the elevation DN and UP relays are

functioning properly. When the LED lights, it tells us that the relay has energized and is sending high

voltage (110vac or 220vac) to the elevation motor.

AC PWR (green) - The AC PWR (Alternating Current Power) illuminates when AC line voltage is

delivered to the treadmill. It then passes through the in-line fuse (110)/s(220) and lights the AC PWR

LED.

+12V (green) - When the proper AC voltage is delivered to the treadmill, passes through the in-line

fuse/s, through the full wave bridge rectifier (changes AC to DC), through the transformer (steps down

Step 2:

DC to +12vdc) then the +12V LED lights.
This the board LED, who control the signal for Main Motor+Elevation Motor. You must see, the LED DN+ UP( both will be Lit) in any position down or Up.

2) The RELAY board is designed with diagnostic LED lights. The LED's are color coded according to

their specific function. Green indicates a properly operating treadmill; the green lights should always

be ON when power is supplied to the treadmill. Yellow indicates a treadmill function. Red indicates a

treadmill malfunction. Here is a list of each LED and what it signifies:

AC PWR (green) - The AC PWR (Alternating Current Power) illuminates when AC line voltage is

delivered to the treadmill. It then passes through the in-line fuse (110)/s(220) and lights the AC PWR

LED.

VDC (green) - The VDC LED will light when it receives DC voltage from the DC power supply.

DN & UP (yellow) - The DN and UP LED lights tell us if the elevation DN and UP relays are

functioning properly. When the LED lights, it tells us that the relay has energized and is sending high

voltage (110vac or 220vac) to the elevation motor.

UPSW (green) - This LED will illuminate when the low voltage dc is delivered from the upper display

board to the elevation UP relay. This low voltage dc is what energizes the coil of the relay.

DNSW (green) - This LED will illuminate when the low voltage dc is delivered from the upper display

board to the elevation DOWN relay. This low voltage dc is what energizes the coil of the relay.

BELTSW (green) - This LED will illuminate when the low voltage dc is delivered from the upper

display board to the belt (motor start) relay. This low voltage dc is what energizes the coil of the relay.

SPD (yellow) - The SPD LED flashes on and off (relative to speed) when the speed sensor is

operating properly.

PWM (yellow) - This LED will light when the upper board is sending a speed signal to the PWM.

Both the PWM LED and BELTSW LED must be lit for belt movement.
Finally this this Relay Board, the Each Led will be Lit, for any Relai control for DN down, or UP for elevation Motor. You must clean contact of the Relay with Special Spray(Radio Schack).

With this you must fix it.

Step 3:

Try this again. and fix it.b) LUBE the gear motor, shaft and turn the POT a little and see if the motor get RPM.

The Steps for Newer Style Console Calibration:

  1. Locate the calibration area on the rear or underside of the console (a hole, near the console's center, that goes through to the electronics board. (This hole should not have a screw in it.)

  2. Insert a pencil (eraser end), into the hole and feel around for the cal button (will click when pressed).

  3. Press the button 2 times (with the pencil eraser). The first click should show CL11 in the console, the second click should show CL21.

  4. If the process was done correctly, and CL21 appears in the console, you are in "calibration mode." The next few steps consists of pressing buttons on the console and observing settings. This will not require any other tools.

  5. Press ENTER. CL22 should display in the TIME window and (??) in the SPEED window.

  6. Press ENTER. CL23 should display in the TIME window and (??) in the SPEED window.

  7. Press ENTER. CL24 should display in the TIME window and (??) in the SPEED window.

  8. Press ENTER. CL25 should display in the TIME window and (??) in the SPEED window.

  9. Press ENTER. CL26 should display in the TIME window. You should then see the letter "E."

  10. Press ENTER. You should see "SS" or "55" in the console.

  11. Push the STOP/START button. For safety, at this point, you should step off, or be off, the treadmill.

  12. Push the ENTER button. The walking belt should start to move, accelerate to maximum speed, then stop on its own.

  13. When the belt stops, the incline should self test by raising to its highest incline position, then lowering back down to its lowest position.

  14. Once the incline test is complete, push the POWER button 2 times. The unit should shut off and the console should go completely blank. If this happens, the treadmill is done calibrating and is ready for use.

  15. If the letter "F" appears in the SPEED or INCLINE window when the power button is pressed 2 times, the treadmill is indicating a failure somewhere either in the SPEED or INCLINE (depending on the window the "F" appeared in).

1_7_2013_8_21_43_pm.jpg1_7_2013_8_22_06_pm.jpg

Jan 07, 2013 | Vision Fitness T9550 Folding Treadmill

1 Answer

Initial calibration keeps failing. the treadmill will not elivate


Step 1:

please see this test and fix it. God bless you

The Steps for Newer Style Console Calibration:

  1. Locate the calibration area on the rear or underside of the console (a hole, near the console's center, that goes through to the electronics board. (This hole should not have a screw in it.)

  2. Insert a pencil (eraser end), into the hole and feel around for the cal button (will click when pressed).

  3. Press the button 2 times (with the pencil eraser). The first click should show CL11 in the console, the second click should show CL21.

  4. If the process was done correctly, and CL21 appears in the console, you are in "calibration mode." The next few steps consists of pressing buttons on the console and observing settings. This will not require any other tools.

  5. Press ENTER. CL22 should display in the TIME window and (??) in the SPEED window.

  6. Press ENTER. CL23 should display in the TIME window and (??) in the SPEED window.

  7. Press ENTER. CL24 should display in the TIME window and (??) in the SPEED window.

  8. Press ENTER. CL25 should display in the TIME window and (??) in the SPEED window.

  9. Press ENTER. CL26 should display in the TIME window. You should then see the letter "E."

  10. Press ENTER. You should see "SS" or "55" in the console.

  11. Push the STOP/START button. For safety, at this point, you should step off, or be off, the treadmill.

  12. Push the ENTER button. The walking belt should start to move, accelerate to maximum speed, then stop on its own.

  13. When the belt stops, the incline should self test by raising to its highest incline position, then lowering back down to its lowest position.

  14. Once the incline test is complete, push the POWER button 2 times. The unit should shut off and the console should go completely blank. If this happens, the treadmill is done calibrating and is ready for use.

  15. If the letter "F" appears in the SPEED or INCLINE window when the power button is pressed 2 times, the treadmill is indicating a failure somewhere either in the SPEED or INCLINE (depending on the window the "F" appeared in).


Step 2:

The SCR lower board is designed with diagnostic LED lights. The LED's are color coded according to

their specific function. Green indicates a properly operating treadmill; the green lights should always

be ON when power is supplied to the treadmill. Yellow indicates a treadmill function. Red indicates a

treadmill malfunction. Here is a list of each LED and what it signifies:

MOTOR (yellow) - The MOTOR LED illuminates when dc (direct current) voltage is sent to the drive

motor. The LED gets brighter when the dc output is increased.

RLC (yellow) - The RLC (R = Reactance / L = Inductance / C = Capacitance) LED illuminates when

the filtering system is properly working. The filtering system includes the capacitor and filter choke. If

there is a short in either component then the RLC light will not come on.

DN & UP (yellow) - The DN and UP LED lights tell us if the elevation DN and UP relays are

functioning properly. When the LED lights, it tells us that the relay has energized and is sending high

voltage (110vac or 220vac) to the elevation motor.

AC PWR (green) - The AC PWR (Alternating Current Power) illuminates when AC line voltage is

delivered to the treadmill. It then passes through the in-line fuse (110)/s(220) and lights the AC PWR

LED.

+12V (green) - When the proper AC voltage is delivered to the treadmill, passes through the in-line

fuse/s, through the full wave bridge rectifier (changes AC to DC), through the transformer (steps down

This the board LED, who control the DC to +12vdc) then the +12V LED lights.
signal for Main Motor+Elevation Motor. You must see, the LED DN+ UP( both will be Lit) in any position down or Up.

2) The RELAY board is designed with diagnostic LED lights. The LED's are color coded according to

their specific function. Green indicates a properly operating treadmill; the green lights should always

be ON when power is supplied to the treadmill. Yellow indicates a treadmill function. Red indicates a

treadmill malfunction. Here is a list of each LED and what it signifies:

AC PWR (green) - The AC PWR (Alternating Current Power) illuminates when AC line voltage is

delivered to the treadmill. It then passes through the in-line fuse (110)/s(220) and lights the AC PWR

LED.

VDC (green) - The VDC LED will light when it receives DC voltage from the DC power supply.

DN & UP (yellow) - The DN and UP LED lights tell us if the elevation DN and UP relays are

functioning properly. When the LED lights, it tells us that the relay has energized and is sending high

voltage (110vac or 220vac) to the elevation motor.

UPSW (green) - This LED will illuminate when the low voltage dc is delivered from the upper display

board to the elevation UP relay. This low voltage dc is what energizes the coil of the relay.

DNSW (green) - This LED will illuminate when the low voltage dc is delivered from the upper display

board to the elevation DOWN relay. This low voltage dc is what energizes the coil of the relay.

BELTSW (green) - This LED will illuminate when the low voltage dc is delivered from the upper

display board to the belt (motor start) relay. This low voltage dc is what energizes the coil of the relay.

SPD (yellow) - The SPD LED flashes on and off (relative to speed) when the speed sensor is

operating properly.

PWM (yellow) - This LED will light when the upper board is sending a speed signal to the PWM.

Both the PWM LED and BELTSW LED must be lit for belt movement.
Finally this this Relay Board, the Each Led will be Lit, for any Relai control for DN down, or UP for elevation Motor. You must clean contact of the Relay with Special Spray(Radio Schack).

With this you must fix it.





Step 3:

please lube the elevation motor, shaft, and gear, and adjust the POT for RPM, and see what happen. see the diagram + block diagram attached for troubleshooting and fix it.
God bless you
1_7_2013_8_26_09_pm.gif1_7_2013_8_26_56_pm.jpg1_7_2013_8_27_18_pm.jpg

Jan 07, 2013 | Vision Fitness T9550 Folding Treadmill

1 Answer

The orange charge light comes on but when I press to start computor nothing happens no green light, the orange light flickers a few times.....I have taken out hard drive and batteries afew time but nothing...


Charger faulty or Motherboard problem.
You can check the power supply of the charger by measuring the DC voltage at the DC jack with a multimeter set to DC volts (red probe on the inner of the jack, black probe on the outer of the jack, should measure 18-20 volts.

Also check the security of the jack in the DC port, make sure it is not loose

See if the Ac adaptor has a green led on it, flashing LED indicates power not being "used " by the laptop

Gut instinct with this being a compaq is that the fault lies in the motherboard

Jan 12, 2011 | Compaq Evo N610C Notebook

1 Answer

First Hello. Before few days,when I turn on my PC(but I was unpluged my machine from electricity) and on monitor displays CMOS wrong set date/time,cpu frequensy.I hit BIOS set up sittings and Windows xp...


Replacing the bios battery was the correct thing to do. Answer me this. The Asus motherboard should have a green LED light lit (Standby power LED), when the system is turned off. Also keep the power cord for the power supply connected at all times. Though it is possible the replacment bios battery was all ready low on voltage or dead. When you're system is turned off the power supply continues to send 5volt DC to the motherboard which maintains the bios 3volt DC.
If the green LED is not lit than there is no power charging the bios battery and every time you boot the system the bios will have lost its settings. If the green LED is red in color, than the problem is within the standby switch built into the motherboard. The standby circuit can not be repaired. Double check all power connectors from the power supply to the motherboard. If everything has a good connection and you're bios settings continue to reset you should consider replacing the motherboard. At this point you have nothing to loose. Install the latest bios update,
(Beta Version 1010.005). 2006/02/14 update.
http://www.asus.com/product.aspx?P_ID=d2Gi3Hr6quXOk51C&content=download

Good luck!
Mike

Jan 23, 2010 | ASUS A7V880 Motherboard

1 Answer

Help w/ the flashing green light


Good Day;

Cause #1 1. Red status LED, self-diagnosis error 44, check for open F9A06 on the Power PCB part # 283P128050 on the Power PCB 2. Red lamp LED, self diagnosis error 34. Check for 5-volts DC at J-9 connector pin 1 and 2 on the Engine Driver PCB if missing replace the Power PCB part # 930B921002 3. LED stops blinking after 70 seconds of plug in but will not power on. This model is equipped with a keyboard lock feature, this can be mistaken as a no power condition. To unlock the keyboard press and hold the "menu" button on the front panel for 10 seconds 4. LED stops blinking after 70 seconds of plug in but will not power on. Check for 3.2 volts DC at connector LE pin 3 and 4 on the Control PCB, if low suspect problems with the switches/buttons on the Control PCB part # 935D776001 5. LED stops blinking after 70 seconds of plug in but will not power on. Keyboard is not locked and key inputs at connector LE pin 3 and 4 check good. Suspect the E2P PCB part # 934C121001 6. (LED does not stop blinking after plug in) Disconnect the USB connector from the card reader to the front from the Chassis, if the LED stops blinking after 70 seconds replace the Card Reader part # 299P271010. 7. (LED does not stop blinking after plug in) Disconnecting the USB connector from the Card Reader did not help. Remove connector FC from the FMT PCB and plug the unit in, if the LED stops blinking after 70 seconds with FC removed suspect a problem on the FMT PCB (part # 930B924002), if the LED keeps blinking with connector FC removed suspect a problem on the DM PCB (part # 934C116002). 8. (LED does not stop blinking after plug in) On the DM PCB (part # 934C116002) check C81A2, C81A3, C81B3 and C81B4 (1000 UFD, 16V, 105C), if any are bad, replace all of them with part # 181P734030 (680 uFD, 16V, 105C). See Service Tip VS-78A 9. (LED does not stop blinking after plug in) On the FMT PCB (part # 930B924002) check C8F19, C8F21, C8F22, and C8F27 (16V 1000 UFD 105C), if any are bad, replace all of them with part # 181P734030 (680 uFD, 16V, 105C). Good Luck, big IRISH.

Oct 19, 2008 | Mitsubishi WD-52725 52". Rear Projection...

2 Answers

NAD 304 power indicator


Change resistors 333 & 334 - 47k-1W

Jan 05, 2008 | Audio Players & Recorders

1 Answer

TV turns off aftering powering up. red LED flashes 3 times.


3 red blinks means th lamp door in not on. if you have installed the lamp door corectly and it still does this solder all three pins together on the door switch.

Oct 08, 2007 | Sony Grand WEGA KDF-42WE655 42" Rear...

Not finding what you are looking for?
Jamo E8 SUB Subwoofer Logo

234 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jamo Audio Players & Recorders Experts

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Tom Chichester

Level 3 Expert

35505 Answers

 Grubhead
Grubhead

Level 3 Expert

5151 Answers

Are you a Jamo Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...