Question about Remote Starter with Keyless Entry

Open Question

I have an RS1200EP control module that constantly clicks like a turn signal flasher and will not start the car?????

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

LOCATION OF TURN SIGNAL FLASHER 2001 BONNEVILLE


It's part of the hazard switch , electronic module !
Turn Signal/Hazard Flasher Module
In the center of the IP part of the hazard flasher switch

2001 pontiac bonneville flasher module-0gh0golvpqxksfrzlnez2sc5-2-0.jpg

Jun 06, 2017 | Cars & Trucks

2 Answers

Turn singles and hazards are not working on my 2001 deville


I would replace the turn signal hazard combo switch.

Nov 28, 2016 | Cars & Trucks

1 Answer

Turn signal


Hi, check you flasher switch first. Or earth wire is not connected.

Jul 20, 2013 | 2004 Dodge Dakota

2 Answers

Where is the fuse for the turn signals on a lincoln continental


Without knowing the year, I'll guess that it's newer than 1998. The turn signals aren't controlled by a flasher. They are controlled by the lighting control module. It's located under the dash, driver's side, just about behind the ash tray. It's held in by 7mm nuts and 2 plastic tabs. Hope I've helped. If so, please rate my assistance and leave a comment. In the event it's older than a '98 and isn't controlled by the module. Turn on the emergency flashers and follow the clicking. That will lead you to the fuse box where you will find a round "DOT 3" fuse/relay.

Dec 04, 2010 | Lincoln Continental Cars & Trucks

1 Answer

At times there is a constant clicking, it


The hazard switch which is just above the radio controls the turn signals and flashers is a very common issue. This is only available from the dealer. Most often this cures this issue.

May 22, 2010 | 2004 Pontiac Grand Am

1 Answer

Stop and TS problem


there is a flasher
.the hazard is wired to constant power so it works with the ignition off.
the turn signal works off of a switched power,to the turn switch and either the right or left turn signal.
if a bulb burns out,the light stays on steady

Jan 29, 2010 | 1998 Mercury Grand Marquis

1 Answer

Turn signal not working


on an older car this woul dsimply mean that the turn signal flasher was burned out for that side. today its more complex. the turn signal flasher is a series of resistors and timer modules located in the workings of the body control module. This can be a simple problem with a shorted line, or a faultly turn switch or something as complex as needing a new body control module. This is something that needs to be repaired by a quality automotive mechnican with an electrical backround, and unfortunatley unless your in the nyc area i have none to suggest to you.

Aug 26, 2009 | 2005 Pontiac G6

1 Answer

Constant clicking from flasher unit


The flasher unit has gone bad and needs to be changed. The flasher module is a part of the hazard module also. The clicking is the unit is still working but there is not enough voltage to activate the lights to flash. It's common on the Malibu's and other GM product cars similar to the Malibu like Grand Am's Ect. I believe Auto Zone has the replacement part for you car and is more reasonable in price then the dealer and the y also have the step by step instructions to replace the flasher module. Good luck and keep me posted, be glad to help.

Jun 03, 2009 | 2002 Chevrolet Malibu

Not finding what you are looking for?
Remote Starter with Keyless Entry Logo

Related Topics:

105 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bulldog Security Vehicle Parts & Accessories Experts

Matthew Spark
Matthew Spark

Level 3 Expert

1066 Answers

John
John

Level 2 Expert

509 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Bulldog Security Vehicle Part and Accessory Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...