Question about DISH Network IR Remote Control

2 Answers

I can not progam my disk network remote to control my new Auria tv. i can use most functions except to on/off and volume

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • DISH Network Expert
  • 146 Answers

Hi, this is Cheri Torres with DISH Network customer service.I came across your question and wanted to see if i could help. :) I was lookingthrough all of our remote codes for all of our IR remotes and I didn't see anycodes for Auria TVs. An option you can try instead of using remote codes is a channelscan. A channel scan will basically go through all of the possible codes wehave and find the correct one for your particular remote and TV. Whendoing a channel scan you will first have to press and hold down the TV buttonon your DISH remote until all the mode lights at the top of the remote light upred. As soon as all the lights are lit, let go of the TV button, press 500, andthen the # (pound) button that is located under the number nine. After thisprocess is done you will press and hold down the TV button again until all themode lights are lit. Then you will press the big red power button once andrelease, next press the up arrow button once every second. You will keeppressing the up arrow until you see your TV turn off, as soon as the TV turnsoff you will press the # (pound) button right away. Once you have completed allthese steps you can try all your TV functions to make sure it is workingcorrectly. I hope you find these instructions useful. If you have anyfurther questions or concerns feel free to post back here or email me atCheri.Torres@Dishnetwork.com.

Posted on Dec 29, 2010

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 185 Answers

Hello, Daniel Busa here with Dish Network's customer service department. The programming process is in the following link: http://www.dishnetwork.com/downloads/pdf/user_guides_and_manuals/Remote_Codes_Web_Page.pdf

Posted on Dec 29, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need a remote control that will have for auria


0071 0101 0113 0152 0181 0236. If you wish to get more; check the site linked here. It has set-up code list & set-up procedure to many popular brand remote controls. Pull up older posts.
http://electrohelponline.blogspot.com/
http://remotesearch.blogspot.com/

Sep 24, 2014 | Televison & Video

1 Answer

Program this remote to control volume on my panasonic tv


Hey teresa_ne685,

Programming the remote to a TV can definitely be done. I have provided the steps below along with a few codes. You can visit the link to look-up your model specific codes!

Link: http://www.dishnetwork.com/SupportSection/remote-setup

Codes: 765, 644, 811, 512, 700, 823

Addressing Remote to TV:

1.) Press and hold the clear TV button until all mode lights light up.
2.) Release and TV light will be blinking.
3.) Enter code and press #. The TV button should flash 3 times.
4.) Try functions (Volume, Power, etc..) and see if working.
5.) If no function, repeat steps 1-4 with another code.

Let me know here if you have any other questions!

Tommy Faust
DISH Network

Oct 08, 2011 | DISH Network IR Remote Control

1 Answer

I have a Dish IR. Not sure of the model number. Uses 4 AAA batts. The problem I have is the every function seems to work fine except for the volume control. In order to change volume I have to use the TV...


It is possible that those buttons have failed, but a bit more likely the remote lost the codes for the TV itself... since almost everything the remote controls... is on the DVR. I apologize if I am guessing wrong in assuming other "TV" buttons (like INPUT) don't function either.

To re-program your remote to recognize your TV (like when the tech first set up the system) choose from the following receiver types to find the correct remote control TV codes for your Zenith.

Remote TV Codes for 722/622/612/411/222/211 Receivers
Remote TV Codes for 625/522/512/510/508/501 Receivers
Remote TV Codes for 811/381/322/311/301 Receivers

Aug 29, 2011 | DISH Network IR Remote Control

1 Answer

I bought a new TV and need to program my Dish network remote control


Hey scrappy32847,

Congrats on the new TV! I can definitely assist you with this and get it taken care of. As I don't know what TV you have I don't have any codes off hand available.

You can check out this link: http://www.dishnetwork.com/SupportSection/remote-setup to get the codes to program your remote. I have also listed the steps below to program that remote to your new TV.

Addressing Remote to TV:

1.) Press and hold the clear TV button until all mode lights light up.
2.) Release and TV light will be blinking.
3.) Enter code and press #. The TV button should flash 3 times.
4.) Try functions (Volume, Power, etc..) and see if working.
5.) If no function, repeat steps 1-4 with another code.

If you need any additional assistance you can reach me here or at thomas.faust@dishnetwork.com

Tommy Faust
DISH Network

Jun 24, 2011 | DISH Network IR Remote Control

1 Answer

How do I program an Echostar 5.4 IR to control a dish network 722 receiver attached to a sony xbr television and the telivision itself. The remote will control the receiver except for the volume and the...


Hi, Cheri Torres with DISH Network Customer Service here. I came across your post recently and wanted to see if I could help. The best codes for the 5.4 IR remote are 500, 578, 514 and 758. I will also list here for you the instructions for addressing your DISH remote to your Sony TV. I hope you find these codes and instructions useful and if you have any further questions or concerns feel free to email directly at Cheri.Torres@Dishnetwork.com. Thanks and have a great day!

Instructions for addressing remote to TV.
  1. Turn the Television On
  2. Press and Hold the TV Mode button until all other mode buttons light up red.
  3. Enter the three-digit code using the buttons on the number pad.
  4. Press the pound (#) button once.
    Note: The LED will flash three times.
  5. Test functionality with the TV
  6. Return to Step 2 if the remote is not able to turn the TV On/Off, change the volume and mute the television.

Feb 19, 2011 | Televison & Video

1 Answer

I got my dish network to turn off the tv and adjust volume but remote wont turn on the tv


Hi there!! This is Kimberly Escobar with DISH Network, just ran across your post and wanted to provide you with some helpful information to help get your problem resolved. If your remote control is functioning as far as turning the T.V off and the volume, one of the things you may want to check is that the power button is working, you can verify this by trying to turn on and off the receiver. If it works for the receiver you will need to try to address the remote to your T.V again using different codes. To address a remote to the T.V we use certain codes that integrate to the remote allowing it to function with the T.V. unfortunately we cannot promise the remote will function the T.V completely. You can find more codes at this link here http://www.dishnetwork.com/SupportSection/remote-setup. If you need any additional help please free to contact us directly at 1800-333-DISH. Hope this is helpful to you.

Feb 10, 2011 | DISH Network IR Remote Control

1 Answer

I can program my new TV to turn on and off but can't get the volume to work.


Hello there! This is Kimberly Escobar with DISH Network just ran across your post and would like to help you by providing you information that may help you get this issue resolved. Depending on the brand of television you have we have certain codes that integrate to the remote allowing it to work functions on the T.V. Unfortunately we cant promise that the remote will work all the functions on the T.V. You can find the different codes in our website at http://www.dishnetwork.com/SupportSection/remote-setup this should help you try different codes and find the one that might work power and volume. If you have any questions please let us know you can contact us directly at 1800-333-DISH.

Feb 09, 2011 | DISH Network IR Remote Control

1 Answer

I have dish network setup, and vizio 42" HDTV. The Dish network remote is already able to control the TV power and sound options, however, I want to control the TV Setup options too (specifically the...


Hello, my name is Becki Barned, with Dish Network customer service. To get your tv to work those particular functions, you will need to reprogram the remote to the tv, finding a code that works all functions of the tv. Some codes will work the power and volume, but not the other functions. Try these steps:

1. Hold down the TV mode button until all lights at the top of the remote are lit up
2. Press the 3 digit code in
3. Press the pound button
4. Press the SAT button on the top left of the remote.

Here are the codes to try:
505
671
627
864
006

Hope this helps!

Jan 01, 2011 | DISH Network IR Remote Control

1 Answer

Get volume and on/off button to work on dish remote


Hello, you may have already gotten this resolved, but here are some simple steps to get this resolved. Just follow this link to our website, and you will be good to go real soon!!!!!


http://www.dishnetwork.com/SupportSection/power-scan-instructions


Becki Barned
DISH Network Customer Service

Jul 31, 2010 | DISH Network IR Remote Control

1 Answer

Code to programme Sky Remote to operate new TV?


i have the same problem with the codes 0035 0125 0049 everything works except turning the volume up. have you found a solution yet???

Dec 31, 2008 | Televison & Video

Not finding what you are looking for?
DISH Network IR Remote Control Logo

710 people viewed this question

Ask a Question

Usually answered in minutes!

Top DISH Network Televison & Video Experts

brian soufane

Level 3 Expert

693 Answers

john milligan

Level 3 Expert

512 Answers

Jaime Hernandez

Level 3 Expert

2318 Answers

Are you a DISH Network Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...