Question about Pasquini Livietta Espresso Machine

1 Answer

My pasquini livia machine is leaking from the base of the steam wand. Perhaps it is a gasket how do you replace these?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 944 Answers

Hi,

You have to take apart the system for changing the gaskets.If you are not a technical savvy don't try for it.Here is the parts diagram for your machine.Many of my fixya customers took apart the system to change the valve and they suffered a lot to fix it again back.All the best.
My pasquini livia machine is - guru_fixya.gif
1 Boiler end gasket 11 Expanse Valve 21 Group gasket 2 Heating element 12 Drain 22 Refill solenoid 3 Gasket for above 13 Pressurestat 23 Group touch pad 4 Steam + water valve 14 Main switch 24 Drip tray grill 5 Pop off valve 15 Group 25 Water flow meter 6 Bleed valve 16 Group solenoid 26 Drip tray 7 Water level Probe 17 Group handle 27 Basket 8 Auto refill relay effect 18 Filter basket single 28 Steam-water valve knob 9 Heater exchanger injector 19 Plastic gasket 29 Manual refill valve 10 Heat wand 20 Site glass 30 Shower screen
guru_fixya_0.gif

the gasket look like this.I will cost around 12$.


Please do rate the solution if the issue is resolved or post a comment for further assistance.

Thank you for using fixya have a nice day:-)

Posted on Jan 03, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have an older Pasquini Livia purchased in the early 90s. It continues to heat up and then the relief valve goes off. Is there a thermostat to replace?


Yes, remove the top panel on the right side is a p. stat with a microswitch on top, either that has to be replaced or the tube is blocked and it cannot read the steam pressure.

Nov 10, 2011 | Pasquini Livia 90 Espresso Machine

1 Answer

Pasquini livia 90 will power up for only few seconds and then shut down you know what iy maybe?


Try this open the steam valve when turning the machine on, if that works then the vent valve needs to be replaced, or the p.stat is damaged.

Feb 18, 2011 | Pasquini Livia 90 Espresso Machine

2 Answers

I need the parts diagram for the pasquini livia 90


I found something on amazon, click here and take a look: Amazon com pasquini livia 90 parts. I hope this was helpful. Cheers

Nov 18, 2010 | Pasquini Livia 90 Espresso Machine

1 Answer

My husband removed the steam wand from our Pasquini Livia because I am running out of steam too soon and I thought the wand needed to be tightened. Now we need to know exactly how the springs go back when...


There should be a brass disk also. The spring goes in first, then the brass disk with the curved side down, then the wand, and then the nut.
Low steam pressure, could be a sign of scale build up, or the heater is getting covered with sediment. The heating element is on the bottom of the boiler on a Pasquini. Also check you pressure gauge. It should b shutting off at 1.1bar of pressure. If it is lower that could be another cause of low pressure. It can be turned up by the pressurestat.

Aug 24, 2010 | Pasquini Livia 90 Espresso Machine

2 Answers

The portafilter basket leaks out the sides no matter how firmly held in place or the quantity of coffee in the basket


Hi
You need to replace the brew head gasket. It becomes hard and will not seal. Order 2 gaskets because 1 always fails on Friday before a big party on Saturday.

Nov 29, 2009 | Pasquini Livia 90 Espresso Machine

2 Answers

The handle is leaking water


Hi
Your brew head gasket needs replacing. They get hard after about 6 months to a year depending on how long the machine is on. if it on 24/7 it need to be changed every 6 months. If turned off daily every year. The gasket is up where you install the portafilter to make espresso. The black ring is rubber and that is what need to be changed. Have one setting right here on my desk.

Nov 09, 2009 | Pasquini Livia 90 Espresso Machine

1 Answer

Our Livia 90 would need a service + the pressure steam valve is leaking. Thanks in advance ! Thilo


If you are local to us perhaps in Orange County, CA we can provide service. If not you may contact Pasquini to get a local certified repair location near you.

As far as the pressure steam valve goes, you most likely simply need a new o-ring kit... we offer kits for new and older units. Older machines would use Part# KSWV-2 for $5.40, newer units would use Part# KSWV-2 for $4.30. I could explain how you could do this service yourself.

My experience is working over 10 years at Pasquini as a master technician running the home repair sales and service center.

I stock all Pasquini parts for any service of your Pasquini espresso machines and grinders. Contact us for any of your Pasquini sales and service needs.

Oct 03, 2009 | Pasquini Livia 90 Espresso Machine

2 Answers

Pasquini. Livia 90 intermittently building up too much pressure


The part that will solve your problem is an upgraded heating rewire kit which will control pressure electronically, not manually. The rewire kit is Part #90000, $28

You may also need a new micro switch which is connected to your PStat with the rewire kit. The micro switch part #7633905, $13

These parts are in stock. I can send you these parts and instructions to install these parts in your machine.

My experience is working over 10 years at Pasquini as a master technician running the home repair sales and service center.

I stock all Pasquini parts for any service of your Pasquini espresso machines and grinders. Contact us for any of your Pasquini sales and service needs.

May 21, 2009 | Pasquini Livia 90 Espresso Machine

2 Answers

Leaking from the grouphead


The fix to this problem is replacing the group head replacement done every 8 months to a year. The part number is #90907 $4.50+shipping and I have this in stock.

My experience is working over 10 years at Pasquini as a master technician running the home repair sales and service center.

I stock all Pasquini parts for any service of your Pasquini espresso machines and grinders. Contact us for any of your Pasquini sales and service needs.

Feb 18, 2009 | Pasquini Livia 90 Espresso Machine

Not finding what you are looking for?
Pasquini Livietta Espresso Machine Logo

1,004 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pasquini Coffee Makers & Espresso Machines Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Steve

Level 3 Expert

3289 Answers

Shrikant Shinde
Shrikant Shinde

Level 1 Expert

12 Answers

Are you a Pasquini Coffee Maker and Espresso Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...