Question about PC Desktops

1 Answer

How do you take off power save mode on a T1100 emachine. When you turn on the computer the monitor says PC in power save mode.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 27 Answers

This means that there is no Video Signal that Is going to the Monitor, I would check all the Connections and make sure that it is plugged in correctly. Also, Not all the time, But in a Rare Case, You need to install the software that comes with the Monitor, I have had this Happen Once or Twice. Hookup the Old monitor, Install the Software, and then Connect the New Monitor, This should work.

Posted on Jul 07, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I try to get a new emachine T1100.How can I get this computer? Thank you.


EMachines are no longer made. You can order replacement parts, but no longer able to order EMachines.

Jun 02, 2011 | E-Machines T1100 PC Desktop

1 Answer

My PC desktop is in power saving mode, how can i put into normal mode?


This is what i do whenever someone asks me to remove their PC from power saving mode.

Follow there

Try clearing the NVRAM as follows:
-Turn off the computer
-Disconnect the monitor.
-Unplug the computer.
-Take out the video card.
-Remove the CMOS battery for a couple of minutes.
-Insert the battery.
-Connect the video card and monitor.
-Turn on computer.

Apr 05, 2011 | E-Machines eMachines Desktop PC

1 Answer

I replaced the Power Supply on an emachine T1100 and labeled the connections for P1, P4 and P6 so I could put them back. The fan came on, but the computer didn't start up. I can't find a place for the...


Forgive me if my first (educated) guess may be off, but the 4-pin connector for which your can't find a connection may go to your
system disk hard drive - all Emachine towers have a HDD (hard disk drive) bootable system disk - and it needs power to allow your T1100 to boot.
The system disk (your only bootable hard drive) is hidden (a little) in a metal enclosure in the front of the tower. The T1100 has a 20GB HDD, and in the "My Computer" display, it appear as "Drive C:", and is powered by a standard 4-pin power connector.

Jan 05, 2011 | E-Machines eMachines Desktop PC

3 Answers

How do I upgrade memory on a t1100 emachine from 256mb


Your emachines eMachines T1100 only supports modules made with a specific type of chip. Should you find what seems to be the exact same memory elsewhere for a lower price, it is very possible that the cheaper memory will not work in your computer. From what I see you should use straight PC-133 Try a site like Kahlon.com-they make sure it works with your computer as would kingston or corsair...
Your maximum amount of ram is only 256mb total.
hope this helps...good luck- please leave a rating...thank you kindly

Apr 26, 2009 | E-Machines T1100 PC Desktop

1 Answer

Computer not communicating a signal to monitor


You can fix that by getting a new graphics card
I'm assuming you have a T3830 emachine.
here's the link to replace video card
http://downloads.emachines.com/userguides/8511279_eM_NG3_chassis_HW_ref_en.pdf
Mark

Apr 09, 2009 | E-Machines eMachines T3830 PC Desktop

1 Answer

Emachines T1100 video card


you need to install driver before putting the graphics card in

Dec 26, 2008 | E-Machines eMachines Desktop PC

1 Answer

NEW LG monitor to work on emachines PC with adaptor


First of all, most monitors now a days are plug and play. Make sure the monitor is secure on both sides. There is also another connecter like the one attached to the CPU on the monitor, so make sure they're both securly attached. Also make sure you have the connector plugged in the correct monitor port. some computers have 2.

Jul 18, 2008 | E-Machines eMachines Desktop PC

1 Answer

T1100 emachine - restarts at windows logon screen


Have you made any hardware/software changes lately? If answer is no, reboot the pc and hit F8 a couple times. This will give you a list of options. Use your arrows and highlight last known good configuration and hit enter. See if your pc boots ok. If you don't have that option or it doesn't boot ok, Repeat the process to get the list. Use the arrow keys to higlight Safe Mode and hit enter. Your pc should boot to safe mode. Click on Start>progams>accessories>system tools>system restore. Choose a safe date about 3 days ago and do a restore. Wait until it's done completely! and see if it's working ok. If this fixed your problem please rate as fixed. If you need more help with this just add a comment and I'll be glad to help out. Thanks.

Apr 11, 2008 | PC Desktops

2 Answers

E-Machine T1100


What kind of BIOS version do you have?? here are some commands for the diverse kind of BIOS.


AMI (American Megatrends, Inc.) BIOS: DEL
Award™ BIOS: CTRL+ALT+ESC
Award BIOS: DEL
DTK® (Datatech Enterprises Co.) BIOS:P ESC
Phoenix™ BIOS: CTRL+ALT+ESC
Phoenix BIOS: CTRL+ALT+S
Phoenix BIOS: CTRL+ALT+INS

Feb 15, 2008 | E-Machines eMachines Desktop PC

Not finding what you are looking for?
PC Desktops Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top PC Desktops Experts

joecoolvette
joecoolvette

Level 3 Expert

5660 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18298 Answers

Are you a PC Desktop Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...