Question about Belkin Wireless Router

1 Answer

I have a belkin router my son cannot access x box live despite me putting in every number from ip address to wap2 passwords it was working fine till i got a new notebook then router seemed to stop working so got new one now notebook working but no x box live please please help!!!

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 708 Answers

WIRELESS SECURITY ISSUES

Step 1 : Connect Router - Computer ( Wired)

Step 2 : Open Router Setup by typing http://192.168.2.1 on the address bar of internet explorer

Step 3 : On the left under wireless click wi - fi protected setup

Step 4 : Leave the password blank and click on submit

Step 5 : Disable it and Click on apply changes

Step 6 : On the left under wireless click Security

Step 7 : Enable 64 Bit WEP

Step 8 : Type a 10 digit number on the key 1 ( 2 in each box )

Step 9 : Click apply changes

Step 10 : on the left under wireless click channel and SSID

Step 11 :Change the Wireless channel to 6

Step 12 : Change the SSID to a different name ( no Spaces )

Step 13 : Click apply changes

Step 14 : Now Scan and connect to this network ( Wireless )



Then ...

PS3 And XBOX :: BELKIN



Step 1:Connect Modem - Router - Computer (Wired)

Step 2:Open Router Setup by typing http://192.168.2.1 on the address bar of internet explorer

Step 3:On the Left click firewall

Step 4:Leave the Password blank and click submit

Step 5:Disable it and click apply changes

Step 6:Scan and connect in the Xbox/PS3/Wii

Step 7: Get the IP Address of the Xbox/PS3/Wii

Step 8:Open Router Setup in the Computer

Step 9:On the left under Firewall Click DMZ

Step 10:Enable the IP Address of the Xbox/PS3/Wii in it

Step 11:Click Apply Changes

Step 13:On the left Under Utilities click System settings

Step 14:Scroll down to the bottom

Step 15:Enable UPnP

Step 16:Click apply changes

Step 17:Test the connection ,Check the NAT

If working then let me know

======================================...
If it is still not working

Open Router setup

At the middle Under internet settings check the WAN IP

IF it starts with 192.168. or 172.16 Then you will have to contact your internet service and ask them to bridge the modem


Regards
TOM

Posted on Dec 29, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change password ?


You can use a Browser (e.g. Safari, Firefox, IE etc) to access the IP address of any router from any computer. But first you must know the IP address (or the factory assigned IP address after a reset) currently assigned to the router. This could be on the back or bottom or in the manual that came with the unit.

OR

Reset the Router by using a paper clip in the round tiny hole on the back. Hold clik button in for 3-5 seconds with router powered on.

Remove power & reconnect.

THEN

Connect the router to a computer via an Ethernet cable. Type the IP address into the URL box and hit return. (The IP address will look like eg. 192.168.1.1 or 10.0.0.xxx. Type this into the URL entry box instead of say xxx.com.">www.xxx.com. )

If the IP address is correct, the Routers Menu will show up in the browser asking for a Password. (The Router factory Password is in the manual.)

Enter the routers PASSWORD or factory password.

Once you have the routers internal menu on the browser screen you can Find the SSID and rename for your Home Network rather than the cryptic factory default. You can set the Router PASSWORD to your choice (use WAP2)

You can set the WiFi Channel number to a less used channel for your suburb (less busy=faster access). You can assign a new IP address to the device. (Use the 192.168.1.xxx or 10.xxx.xxx.xxx group number that is made available for the public). You will also have to enter the IP address of your Internet Service Provider and a PASSWORD for your ISP Account. If you don\'t have your ISP\'s preferred DNS IP handy then you can enter 208.67.222.222 or 8.8.8.8. (I found these give 20ms faster response)

Use the SAVE button on the screen to save your settings. This will take a minute and restart with the new settings. You should be set to go.

Once you have it all working.... don\'t forget to copy all the settings onto paper for future reference. On a Mac, just press Cmd Shift 4 and draw a box around the menu settings. This will end up as a screen shot on the Desktop. This saves a lot of writing. Rename the screen shots to something meaningful. (e.g. My Router Settings Page1)



Good Luck

Trevor

Sep 09, 2014 | D-Link DIR-820L Wireless Router - IEEE...

1 Answer

How do i login into my windstream router?


Same as any Router....



You can use a Browser (e.g. Safari, Firefox, IE etc) to access the IP address of any router from any computer. But first you must know the IP address (or the factory assigned IP address after a reset) currently assigned to the router. This could be on the back or bottom or in the manual that came with the unit.

OR

Reset the Router by using a paper clip in the round tiny hole on the back. Hold clik button in for 3-5 seconds with router powered on.

Remove power & reconnect.

THEN

Connect the router to a computer via an Ethernet cable. Type the IP address into the URL box and hit return. (The IP address will look like eg. 192.168.1.1 or 10.0.0.xxx. Type this into the URL entry box instead of say xxx.com.">www.xxx.com. )

If the IP address is correct, the Routers Menu will show up in the browser asking for a Password. (The Router factory Password is in the manual.)

Enter the routers PASSWORD or factory password.

Once you have the routers internal menu on the browser screen you can Find the SSID and rename for your Home Network rather than the cryptic factory default. You can set the Router PASSWORD to your choice (use WAP2)

You can set the WiFi Channel number to a less used channel for your suburb (less busy=faster access). You can assign a new IP address to the device. (Use the 192.168.1.xxx or 10.xxx.xxx.xxx group number that is made available for the public). You will also have to enter the IP address of your Internet Service Provider and a PASSWORD for your ISP Account. If you don\'t have your ISP\'s preferred DNS IP handy then you can enter 208.67.222.222 or 8.8.8.8. (I found these give 20ms faster response)

Use the SAVE button on the screen to save your settings. This will take a minute and restart with the new settings. You should be set to go.

Once you have it all working.... don\'t forget to copy all the settings onto paper for future reference. On a Mac, just press Cmd Shift 4 and draw a box around the menu settings. This will end up as a screen shot on the Desktop. This saves a lot of writing. Rename the screen shots to something meaningful. (e.g. My Router Settings Page1)

Good Luck

Trevor

Sep 05, 2014 | Computers & Internet

1 Answer

Trying to find a wap2 code to hook up xbox thru router. have no idea what I'm doing


If you can access router from pc/laptop, go into the wireless setup and go into security tab. here is where the code is located. Also check the bottom of the router. If you haven't changed the key, many routers have the key printed on the bottom of the router.
To access router, type in he ip address of router, if you don't know the ip address, follow this example.
START-PROGRAMS-ACCESSORIES-COMMAND PROMPT.
BLACK SCREEN WILL OPEN. Do nothing but type in ipconfig This will give you both the wireless and wired ip and the default gateway. You want to write down the default gateway. next type EXIT and the command prompt box will close.
Next open your browser (ie. Internet Explorer Firefox etc...) and type in only the default gateway ip address. example 192.168.0.1 there are no spaces and nothing added before the ip address. This will give you access to the routers access page. You may need a password to get into the router. Usually there is no username and the pw is admin. Then follow alone with what what written above.
Hope that helps.

Jun 02, 2011 | Belkin Wireless Surf Router (F7D2301)

1 Answer

What website do i go to to change my WAP2 password?


Your standard gateway's ip is the login address of your router.
Most Belkins use 192.168.2.1

Aug 20, 2010 | Gateway Cable/DSL Router - 4Port [ Belkin...

1 Answer

I need a 1 800 # for belkin customer support please i need to add ports on my belkin wireless router for x box live


Connect your router to computer with ethernet cable then you can access it with following default link.
http://192.168.15.1
or
http://192.168.2.1
or http://192.168.1.2
If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it.
Then it ask for user name and password.
Type user as "admin" and password as "admin" or "password" or blank or "1234".
Then you can see configuration page of router.
Then click on NAT port forwarding then open port which you want to open.

Let me know if you need further assistance.
Thanks for using FixYa.

May 31, 2010 | Belkin Computers & Internet

1 Answer

I'm trying to set up a new laptop to my belkin router


When you first setup a wireless router you need to connect the wireless router to the computer with a LAN cable.
Then you open a browser such as Microsoft Internet Explorer and on the address bar you type the IP configuration address of the wireless router eg. for Belkin wireless router it is http://192.168.2.1
Enter the default login name and password.
You should change the password and you should setup WAP or WAP2 encryption (WAP2 is the strongest encryption) and change the SSID and turn off SSID broadcast.
For further wireless protection enable MAC address filtering. The MAC address of the wireless card is entered in the router MAC address filter table, which allows only the wireless card with this MAC address to connect to the router.
The wireless card on the computer needs to be configured with the wireless router's settings. The LAN cable can be removed and the computer communicates wirelessly with the router.

Sep 20, 2009 | Belkin Wireless G Plus MIMO (F5D9230-4)...

1 Answer

My son wants to do xbox live but cannot gain access to our wireless router. I have a vista pc connected to the router and 2 other computers in the house that connect fine. Help me please...son driving


Please open your router page and open the DMZ page give an IP address.
Then open X-box page and force the same ip address it will allow your x-box to communicate with the router.

May 21, 2009 | Linksys Wireless-G WRT54G Router

1 Answer

Wireless


Have you configured the Belkin wireless router?
You need to configure the Belkin using a 10baseT network cable first before you configure the wireless card.

To make your wireless router secure you need to use your browser and type in the Belkin IP configuration address.
Then you need to change the Admin password, change SSID and turn off SSID broadcast, setup the encryption (use WAP or WAP2 if your wireless card supports WAP) and for added protection use MAC address filtering.

Apr 12, 2009 | Acer Computers & Internet

1 Answer

Linksys router


Hi Angel,
You don't have to use the install cd. Got to start>run and type in CMD. In the black box that opens, type in IPCONFIG. Look at the list of info presented, till you see Gateway IP, Put those numbers, probley 192.168.x.x, in the address bar of your Internet Explorer. An access window will pop up, For user, put in admin, leave the password blank, or use the word password to access your router. Good Luck!

Jan 05, 2008 | Belkin F5D7230-4 Kit (F5D7230V4SNPDQ)

Not finding what you are looking for?
Belkin Wireless Router Logo

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top Belkin Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2260 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18390 Answers

Are you a Belkin Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...