Question about Garden

1 Answer

The gemini gate motor is opening very slowly, some times not even opening.

Posted by Anonymous on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Most probably faulty battery!

Posted on Oct 30, 2012

  • Gerhard Jacobs Oct 04, 2013

    I'm having the same problem, and I have already changed the batery with a new one but still have the same problem

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What could be a problem with and gemini 12 v system gate motor since it started to move slowly and now its not opening at all. I have changed the battery but still its not opening.Its 3 days now


you may have too much weight on the pinion. Has the gate sagged to the point where the wheel track is bowed? Is the wheel track dirty, or caught some debris? Make sure the wheel track is straight and clean. If the motor was run with low-voltage, it may have harmed the armature. Reduce the load, and see if the motor runs at all. http://www.techniqnorthwest.co.za/GEMINI12VSystem%20gate%20motor.pdf

Apr 20, 2016 | Miscellaneous

2 Answers

Lift gate will not power down to closed when button on gate or remote is pushed. Lights do flash though.


There are switches on both ends of the course of the motor, if one fails it will only work on the side that´s ok. That´s why it opens but do not close.Check it out.

Oct 24, 2015 | Cars & Trucks

1 Answer

What could be wrong? Our Gemini gate motor works well for some time, but then all of a sudden just go backwards when it should close the gate. It just revers with each attempt to let it go forward till at...


You could have dirty photo cells or some obstruction that the photocells are picking up that triggers the safety mechanism to reopen the gate so that no one gets hurt.

Extreme weather conditions (heat and cold) can damage the electronics in the photo cells too.

Are the batteries low on the transmitter?

Typically, photo cells are (or should be) wired to the control board so that it will stop the gate or barrier during the closing cycle should there be a problem- and should fully open again- just like on automatic garage door openers; it's the exact same principal.

Feb 28, 2015 | Cars & Trucks

1 Answer

How to program a ET BLU MIX remote on a older type centurion d5 gate motor


Ask the shop what to do when their suggestion does not work.

Oct 02, 2014 | Televison & Video

1 Answer

Gemini gate motor


Check if it has stops anywhere in the system, usually there are micro switches that are activated by arms, etc that tell it how far to open and close. You may need to adjust them.

Aug 20, 2014 | Cars & Trucks

1 Answer

How to programme a nova 4 button remote on a gemini gate motor


It's important to know that the Nova remote controls are not compatible with the Gemini gate motor. In order to get these remote controls to work with your Gemini gate motor, you'll need to install a Centurion receiver first (see http://www.centsys.co.za/upload/product_link_files/CS37_Nova_Receiver_Instructions_1031.D.05.0012_4.pdf). Once the Centurion receiver has been installed on your Gemini gate motor, follow the programming instructions as per the leaflet that accompanied your brand new Nova remote control, or download the instructions from http://www.centsys.co.za/upload/product_link_files/English_Transmitter_InsertCS37_1031.D.02.0027_1_Nova.pdf

Feb 22, 2012 | Televison & Video

1 Answer

My gate is equipped with a D3 Centurion gate motor. When I push the button to open the gate, the motor turns in the opposite direction (close) and tends to close further. Then if I deactivate the gear box...


if you push the open button and it closes indicates that you have the wrong polarity connected to the motor
gate motors are DC so where the positive and negative wires are connected are critical for rotation direction of the motor

Jul 29, 2017 | Garden

Not finding what you are looking for?
Garden Logo

Related Topics:

504 people viewed this question

Ask a Question

Usually answered in minutes!

Top Garden Experts

Dennis Key
Dennis Key

Level 3 Expert

2475 Answers

john h

Level 3 Expert

11122 Answers

yadayada
yadayada

Level 3 Expert

75117 Answers

Are you a Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...