We keep getting error codes when using our machne

Hello Friend, this is Z. Thank you for your post!

If you are receiving an error code PAUSE, it commonly indicates that the door of your washer is not securely latched or the cycle has been interrupted. Try pressing "PAUSE/CANCEL" or "START/PAUSE" once to resume cycle. If these basic troubleshooting tips prove ineffective, try reprogramming your appliance by unplugging it or flipping the household circuit breaker off. It is best to wait approximately ten minutes and then turn on your washer. If the issue persists, then your washer could possibly have a faulty door latch or experiencing a communication error with the control board. I would personally contact a professional to accurately diagnose your washer to determine the root cause to reduce the risk of unnecessary parts.

ur voltage is flactuate and low voltage is a cause of 0002. pls set ur voltage stabilizer at 230 output

solution E000840-0001...????

i have intec cp2020 machine showing error code close the frond cover error code 330.already closing frond cover.what is the problem machne i will wait for replay.i will check the pwersupplay board & fuse

The F1 error code on this washer indicates a Primary Control Board failure.



It is likely that the machine control board will need to be replaced to correct this problem.



The part number for the machine control board is undetermineable because you have not provided me with the exact model # of your washer.



The procedure for replacing the machine control board is provided HERE

LINK: http://media.fotki.com/1_p,wfgstgtftbtkrrdxgtqsskgwtqkq,vi/gfsfgfsgqxgfqtqtgwf/1/1303472/5961857/image55806img-or.gif



NOTE: Be sure to unplug the washer to disconnect electrical power before accessing internal components.



There is a slight possibility that a problem with the pressure switch hose could be causing this problem.

A pinched or twisted air hose can cause this fault code.

When you open the console, check the air hose connected to the pressure switch on the machine control board.

If it is pinched or crimped, I recommend rerouting the hose to resolve this problem.

This may fix your problem without replacing the control board.



NOTE: You may want to check for this condition before ordering the control board. Most electronic control boards cannot be returned for a refund or credit.



If you find no apparent problems with the air hose on the pressure switch, then replacing the machine control board on this washer should correct your problem. There is a risk involved in replacing this part yourself.

As noted above, you could have a problem with the air pressure hose that is not apparent upon your initial inspection. A service technician would normally need to properly and thoroughly diagnose this problem before replacing the control board.





Thanks for using FixYa - a 4 THUMBS rating is appreciated for helping with your FREE question%%%%

The F1 error code on this washer indicates a Primary Control Board failure.



It is likely that the machine control board will need to be replaced to correct this problem.



The part number for the machine control board is undetermineable because you have not provided me with the exact model # of your washer.



The procedure for replacing the machine control board is provided HERE

LINK: http://media.fotki.com/1_p,wfgstgtftbtkrrdxgtqsskgwtqkq,vi/gfsfgfsgqxgfqtqtgwf/1/1303472/5961857/image55806img-or.gif



NOTE: Be sure to unplug the washer to disconnect electrical power before accessing internal components.



There is a slight possibility that a problem with the pressure switch hose could be causing this problem.

A pinched or twisted air hose can cause this fault code.

When you open the console, check the air hose connected to the pressure switch on the machine control board.

If it is pinched or crimped, I recommend rerouting the hose to resolve this problem.

This may fix your problem without replacing the control board.



NOTE: You may want to check for this condition before ordering the control board. Most electronic control boards cannot be returned for a refund or credit.



If you find no apparent problems with the air hose on the pressure switch, then replacing the machine control board on this washer should correct your problem. There is a risk involved in replacing this part yourself.

As noted above, you could have a problem with the air pressure hose that is not apparent upon your initial inspection. A service technician would normally need to properly and thoroughly diagnose this problem before replacing the control board.





Thanks for using FixYa - a 4 THUMBS rating is appreciated for helping with your FREE question

get a laser lens cleaning disk .($2 to $10) . it looks like a standard CD but has fine little burshes that remove dust from the laser ...that may not work if anyone smokes around the machne .. in that case the cover has to be removed and the laser manually cleaned (with eye glass cleaning fluid on a soft paper towell) ..if that doesnt work then the laser may be just worn out ... replacement is usually more than the cost of a new unit ... make sure your disks are clean .. you can wash the shiney side with mild soap and water ... rince and pat dry .. dont use hot water ...

You are working it too hard. Back off the percentage. But first, let it thaw. Id be inclined to use a fan in the area. You might need two machnes in this space. Do not allow outside air into the space until you get it a little more dried out.

I hope this works for you

a

Try to "slow" down the fax "speed"

hello! i just checked the dervice manual for the rror202 that you said that you are having did not find that code could you clarify thanks brother sr tech