Question about Office Equipment & Supplies

1 Answer

No feed I have got a intermec PX4i that comes up with the following message when the feed key is pressed "Power supply under voltVSTM", have tried changing the power supply but still the same fault

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Sorted

Posted on Jul 08, 2008


1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Intermec PX4i printing blank labels


I found the following item on page 3 in the printhead installation manual:
"Note: If you are installing the 400 dpi printhead on the PX4i

printer (Kit P/N 850-812-900 IPL Only), you must first

update the IPL firmware to version 2.74 or later."


I assume this is a partial exception to the general caution on page 1 of the same publication:


"When installing a printhead, make sure that the printhead

density and alignment is the same as in the one you replace

and that the printhead is designed for the type of printer in

which you are going to install it."


Also, the printer should not be powered when the printhead is being installed. The printer does not identify the printhead until it goes through a power-on startup.

Feb 27, 2012 | Intermec PX4I Label Printer

1 Answer

Intermec PX4i label printer. Paper/Ribbon loaded correctly, but ribbon is 'rippled' meaning barcode label being printed has white lines across it. Any ideas?


Ribbon Wrinkle as it called can be caused due to the main feed rollers (that touch the ribbon or the label) being slightly worn. Even if you have a sligh gradient on the roller(s) it will pull ever so slightly to one side. If you need the parts then please do not hesitate to contavct me. Jack Woodworth - Codeo UK, 01179064587

Oct 19, 2011 | Intermec PX4I Label Printer

1 Answer

ERROR: ribbon fitted (printer: intermec PX4i ) where and what needs to be changed in the settings?


TTR- Thermal transfer- set for using a ribbon. DT- Direct thermal - set when using thermal labels but no ribbon.

Sep 06, 2011 | Intermec EasyCoder® PX4i Label Printer

1 Answer

I am getting a paper fault error when I load a continous paper stock, is there a way to chante the settings to fix this.? My prnter is an intermec PX4i


I hope this helps, this is the solution of there website. If this isnt your problem please respond and i will assist you further.

The Label stock must be fed between the upper and lower guides plates. The path that the label must follow is shown on a sticker inside the media cover. If the media cover is missing download the manual
by clicking on the link below. Verify that the green label guides are adjusted so that the labels stay against the inside wall of the printer.

Depress and hold the Shift Key then press and release the Feed key. The printer should feed some labels during which it performs an auto calibration of the sensor. If the error continues perform the following.

Both the upper and lower sensor halves are mounted on an adjustable bar assembly. The upper and lower guide plates slide over this assembly and can easily be removed for routine cleaning and inspection. Should the sensor window in either half of the guide plates be scrached or damaged, it must be replaced.

The sensor is adjusted by a slot head screw located under the metal lever opened to gain access for loading labels between the guide plates. Once opened the adjusment screw is exposed.

Once you have verified the the following and the problem persists then the sensor is itself is possibly the problem and Service should be contacted.


1. stock is loaded correctly.
2. Sensor assembly is adjusted out over the label.
3. Sensor and guide plates are clean and clear of debris or defects.
4. Configuration settings are correct (label length and media type, gap,mark or continuous).


This is the link to the 501 XP users manual
http://epsfiles.intermec.com/eps_files/eps_man/96042502.pdf

Sep 21, 2010 | Intermec EasyCoder® PX4i Label Printer

1 Answer

I am getting a paper out message all the time. I have Intermec 2-1 labels loaded at the moment


Reload back the fingerprint firmware v8.78.1 into the printer.and try to press shift button together with feed button.

Jun 29, 2010 | Intermec EasyCoder® PX4i Label Printer

1 Answer

The intermec is show a "ribbon fitted" error on the machines screen


its because the printer is setup Direct Thermal, and the sensor see ribbin present. need change setings.

May 21, 2010 | Intermec EasyCoder® PX4i Label Printer

1 Answer

Time out error. Locks up..


Hello , I you printer displeyed Error Time-out , You need to load the memory card (flash card with Fingerprint) Pozdrawiam lukas

May 22, 2009 | Intermec EasyCoder® PX4i Label Printer

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Office Equipment & Supplies Experts

kakima

Level 3 Expert

102366 Answers

k24674

Level 3 Expert

7993 Answers

yadayada
yadayada

Level 3 Expert

70387 Answers

Are you an Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...