Question about Sears Craftsman LiftMaster Chamberlain Garage Door Opener Wireless Keypad Model 976LM Security+

1 Answer

The remote battery was replaced and have lost the connection to the drive. tried to hold the remote to the drive. the lght blinks but does not reset the the remote.??

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 3,197 Answers

Hold the button down on the remote and then press and immediately release the smart/learn button.

Posted on Dec 28, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

HOW TO RESET LG 55A980V-ZA


Reset the remote control by pressing and holding both the ENTER and MUTE buttons for 5 seconds. (Once the reset is complete, the light on the Pointer blinks.) Then re-register the remote by pressing the ENTER button on the remote control while aiming it at your TV.

I am assuming that you have first replaced the batteries in the remote with some fresh ones, and have checked to make sure the emitter LED is not dirty.

Apr 18, 2015 | LG Televison & Video

3 Answers

Compaq presario cq60 the caps lock blink constantly


You may try this fix. No guaranties though. Remove the battery and unplug power cable. Then hold down the "power" button for about 10 seconds. After that plug it back in and try turning it on. Again, this may NOT work but it has for others.

Sep 08, 2014 | Compaq Presario CQ60-220US PC Laptop

1 Answer

My harmony 200 remote logitech needs reset it keeps blinkng


  • It's in safe mode
  • Remove a battery
  • While holding the 2 button on the number pad section of the remote, replace the battery
  • Let go of the 2 button
  • This will take it out of safe mode
  • The device buttons will stop flashing and the remote will work

Dec 06, 2012 | Logitech Harmony 550 Remote Control

1 Answer

Remotes will not sync they just blink and blink.


hold down the button under the button in the battery pack cover and click the one on the front off the wii under the hidden pannel and point at sensor

Jan 07, 2012 | Nintendo Wii Console

2 Answers

How do i reset my rc traxxas stampede?


Hi there,

I don't believe the reset (or syncing) is necessary on this model. However, on similar models you pull the batteries from the vehicle and the remote. Wait 30 seconds. Replace with fresh (or tested as good) batteries.

Best regards

Mike

Nov 20, 2010 | Traxxas Stampede Monster Truck Rtrw/Xl 5

1 Answer

No video,hard drive running but indcator lght not blinking but it is not busted.reset button not functioning


Refresh all the connections to the motherboard and clean the RAM like shown in the image below.025c6b0.jpg
If nothing happens, reset the JCMOS1 (highlighted in the image below).
6efb800.jpg

Shut down the PC first and remove the power cable connected to the power supply. Then change the jumper settings from 1-2 to 2-3 for approx. 10 secs. restoring the jumper to original settings (1-2). Connect the power cable and turn on the PC.
Hope this helps

Sep 29, 2009 | Biostar M7VIG-400 (M7VIG 400-COMBO4)...

1 Answer

Lost blue; otherwise normal; blinks 5x


If the TV standby light is blinking for five times then you may perform the steps given below:
(i) Turn off the TV then disconnect all the cables from the TV.
(ii) Next, reconnect all the cables after two minutes.
(iii) Please make sure that the power cable from the TV is directly connected to a functional wall outlet.
(iv) Next, you may try resetting the TV to the original factory settings.

Please follow the steps that are mentioned below to reset the TV to the original factory settings:

(a) Turn ON the TV.
(b) Press and hold the Power button on the Remote Control supplied with the TV, then press the Power button on the TV front panel.
(c) Release the Power button. The TV will turn itself off, then back ON again.
(d) Next, release the Reset button on the Remote control.

If the standby light still blinks then the issue may be with the projection lamp in the TV and requires replacement.

Jul 12, 2009 | Sony FD Trinitron WEGA KV-32FS120 32" TV

Not finding what you are looking for?
Sears Craftsman LiftMaster Chamberlain Garage Door Opener Wireless Keypad Model 976LM Security+ Logo

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sears Building Materials Experts

Mike

Level 3 Expert

4336 Answers

Cindy Wells

Level 3 Expert

5105 Answers

Brad Brown

Level 3 Expert

15557 Answers

Are you a Sears Building Material Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...