Question about Nintendo Wii Fit for Wii

1 Answer

When I go into any mode, and the game asks me to step off and press a, it waits a few seconds and then repeats itself

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,098 Answers

The sensors need to be reseated.

  1. Take the batteries out.
  2. Take out the screws from each foot in every corner of the board using a Philips screwdriver. Remove the back cover.
  3. The sensors are located on each corner, it is a metal plate. Loosen the screws using TORX screwdriver.
  4. Re seat the small metal plates by putting it back. Don't screw too tight.
  5. Put the cover back and foot on. Put the batteries back in

Posted on Jan 02, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to how to unlock car radio 2008 Chevy Impala


Requirements
The theft lock radio must be in "LOC" mode.

Procedure:
1. Turn the ignition ON (The radio should display "LOC")
2. Hold down the Radio Presets 2 and 3 buttons for six seconds
3. The radio display changes from LOC to a three-digit number. Write this number down. You now have fifteen seconds to complete the next step.
4. Press the AM/FM button
5. The radio display changes to another three-digit number. Write this number to the right of the first one.
6. You now have a six-digit number, the first three digits are from STEP 03 and the last three digits are form STEP 05
7. Call 1-800-537-5140
8. Press 1 then # (pound). You'll hear "Invalid Code, try again"
9. Press 139010 or 106010 or 206010 or 202107 then # (pound). You will be asked to enter your four or six digit code followed by *
10. Enter the number from STEP 6 then *
11. Listen to the four-digit number and write it down. It will be repeated twice
12. Turn the ignition ON (The radio displays LOC)
13. Use the MN and HR buttons to enter the code from STEP 11
14. Press the AM/FM button. The radio display changes to "SEC". Your radio is now "un-locked" and usable.


Dealership Codes
  • 139010
  • 106010
  • 206010
  • 202107
Troubleshooting
If you fail to enter the correct code eight times, the radio goes into INOP mode. You have to wait an hour with the ignnition on before the radio returns to LOC mode.

Aug 14, 2015 | Cars & Trucks

Tip

LG LH-D6235 DVD Region Free Fix


LG LH-D6235 DVD Home Theater Region Free Fix


6201112.jpg

Would you like to make your LG LH-D6235 DVD Home Theater Region Free?

Follow these steps:

  1. Press the Pause button on your remote control
  2. Using your remote control enter the code 3, 1, 4, 1, 5 and 9 (If your unit does not enter the following mode which enables you to enter a region code, repeat steps 1 and 2. You may need to enter these codes in a shorter time span for them to work.)
  3. Press the 0 button on your remote control for Region free, 1 for Region 1 or 2 for Region 2.
  4. Press the Pause button on your remote control
  5. Power off your player and wait a few seconds
  6. Power on your player

I hope that helps.
____________________________________________________________________
Download LG LH-D6235 Home Cinema System Manual

on Jul 14, 2010 | Televison & Video

Tip

LG LH-D6235 Region Free Fix


LG LH-D6235 DVD Home Theater Region Free Fix


6201112.jpg

Would you like to make your LG LH-D6235 DVD Home Theater Region Free?

Follow these steps:

  1. Press the Pause button on your remote control
  2. Using your remote control enter the code 3, 1, 4, 1, 5 and 9 (If your unit does not enter the following mode which enables you to enter a region code, repeat steps 1 and 2. You may need to enter these codes in a shorter time span for them to work.)
  3. Press the 0 button on your remote control for Region free, 1 for Region 1 or 2 for Region 2.
  4. Press the Pause button on your remote control
  5. Power off your player and wait a few seconds
  6. Power on your player

I hope that helps.
____________________________________________________________________
Download LG LH-D6235 Home Cinema System Manual

on Jul 14, 2010 | Audio Players & Recorders

1 Answer

Get in to bios acer aspire AST180-ED400A


First shut your computer off. Wait a few seconds (to allow the hard drive to stop spinning) and start the computer again.
Start repeatedly pressing F2 while the Acer logo is displaying. Press it once, wait a second, press, it again, wait another second, and repeat this while the Acer logo is displaying until you see the bios setup screen.

Feb 19, 2015 | Acer Computers & Internet

1 Answer

My ps3 is not working through the hdmi cable. There is sound but no picture. I've tried in different ports but its the same every time.


Follow these very simple steps to reset your display :-

Step 1.

Turn the Playstation 3 off into standby mode (red light on)

Step 2.

Press and hold the power button. The console will beep when you first press it, then beep again 5 seconds later. Let go of the power button when you hear this second beep

Step 3.

Wait for the Playstation 3 display to initialize.

Your Playstation 3 should now display properly and you can get back to your gaming!

Hope this tip helps you out

Dec 31, 2010 | Video Game Consoles & Games

1 Answer

I have the unlock code for my 99 saturn sl2 but i need the radio layout


Hello, you will need to enter your radio unlock code using these instructions.


  1. Press SEEK DOWN, SEEK UP, TUNE DOWN, or TUNE UP. The radio display should show 0000.
  2. PRESS SEEK DOWN to set the first digit.
  3. Press SEEK UP to set the second digit.
  4. Press TUNE DOWN to set the third digit.
  5. Press TUNE UP to set the fourth digit.
  6. If the code was entered correctly, the radio will display SEC (SECURE). The theft deterrent system for the radio is now active and normal operation may be resumed. If the code was entered incorrectly, the radio will display Err for 5 seconds and the LOC (LOCKED) will be displayed again. If LOC is displayed, repeat 1-6.
  7. If the correct code is not entered in 8 attempts, follow the next steps:
  8. 7.1. Turn ignition to ACC position. 7.2. Turn radio power switch OFF. 7.3. Wait one hour before repeating steps 1 through 7. If attempts to unlock the system are made before the one hour period is up, the radio will display INOP (INOPERATIVE). Continue to wait. If the ignition is not in the ACC position, power will never reset internally to allow itself to be unlocked. 7.4. After one hour, repeat steps 1-7.

Jul 03, 2010 | 1999 Saturn SL

1 Answer

Playstation not registering with hdmi or video mode suddenly


Please try the following steps :-

Step 1. Turn the PS3 off into standby (red light on)

Step 2. Press and hold the power button. It will beep once when you press it, then once more 5 seconds later. Let go of the power button when you hear this second beep.

Step 3. Wait for the PS3 to reset display settings back to standard.

Hope this helps

Nov 05, 2009 | Sony Playstation 3 (PS3) Console

7 Answers

Black DSi frozen.


Everyone i just found out how to fix a black or white dsi that is frozen and wont turn off!!
Step one:unplug dsi (if it is charging)
step two:close the dsi
step three:once it is closed turn volume down all the way witout opening
step four:set the dsi in front of a fan vent or someplace it will get a breeze
step five:open the dsi and hold power switch for like 6 to 10 seconds
(even when it turns off keep holding it for a couple more seconds)
now you an plug it back in and turn it on and VAWALä
hope this helped:)

Jan 02, 2009 | Nintendo DSi White Console

2 Answers

Waste ink tank full


All you need to do is reset the printer counter.
Follow these instructions:
Press MENU then COPY then #.
Press the "+" until you see TEST mode in the window. Press SET. Press 8 (wait a few seconds), then 3 (wait a few seconds) then 0 (again wait a few seconds). The printer counter will reset. Press on/off. If the machine does not turn off - unplug it.
This absolutely worked for me.

Aug 30, 2008 | Canon Office Equipment & Supplies

1 Answer

Vtech,5.8 3-phone w/digital recorder, model DS4122-3 None of the phones work they either say connecting or put back in the charger . these are only 2 months old?


To deregister ALL handsets:
Step 1: Press and hold FIND HANDSET on the main telephone base for 10 seconds.

Step 2: When the IN USE light starts to flash, release the FIND HANDSET button.

Step 3: Press and release FIND HANDSET again. The IN USE light will turn off and in a few seconds, all handsets will be de-registered.

Step 4: All handsets will show NOT REGISTERED.

To register a handset (register 1 handset at a time):
Step 1: Place the handset in the base unit or a charger that is connected to a power outlet. If PRESS FIND HNDST 4 SEC ON BASE does not appear on the screen after a few seconds, lift up handset and place in base or charger again.

Step 2: On the telephone base, press and hold FIND HANDSET for four seconds. Release FIND HANDSET once the IN USE light comes on.

After a while the handset will emit a series of tones, the newly registered handset will be assigned the lowest extension number not previously assigned to another system handset (1-4) when successfully registered. Repeat Steps 1 and 2 if the handset does not successfully register to the telephone base within two minutes.

REPEAT THE REGISTRATION PROCEDURE FOR EACH SYSTEM HANDSET.

Make sure the handsets are not receiving interference from other appliances, cell phones, etc.

IF deregistering does not work .. you will need to reset the entire system
Step 1: Disconnect the power to the telephone base.

Step 2: Disconnect the handset battery.

Step 3: Wait a few minutes and then reconnect the power to the telephone base.

Step 4: Reconnect the handset battery

Step 5: Wait about one minute for the handset to re-establish a link with the telephone base and then test the phone again.
You will need to set the time and date again after resetting the entire system.

Mar 11, 2008 | Lands Phones

Not finding what you are looking for?
Nintendo Wii Fit for Wii Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nintendo Video Game Consoles & Games Experts

Bee Santiago

Level 2 Expert

268 Answers

Raj Patel

Level 3 Expert

899 Answers

phil

Level 2 Expert

567 Answers

Are you a Nintendo Video Game Console and Game Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...