Re: How do I get the controller working with a X box
All you do is find the sync button (located at the back of the controller its small so look hard) Thats the sync button. Then press your xboxs sync button at the same time. No problem.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
The LG AKB73615337 remote control is designed specifically for LG TVs and may not be compatible with the Xfinity Flex box. However, you can try the following steps to see if it works:
Ensure compatibility: Confirm that the LG remote control is compatible with the Xfinity Flex box by checking the list of supported devices in the remote control's user manual or by contacting LG customer support.
Power on the Flex box: Make sure your Xfinity Flex box is powered on and connected to your TV.
Activate pairing mode: Put the LG remote control into pairing mode by simultaneously pressing and holding the "Back" and "Home" buttons for a few seconds until the LED light on the remote starts blinking.
Follow the Xfinity Flex box pairing instructions: Refer to the Xfinity Flex box's user manual or contact Xfinity customer support to find the specific instructions for pairing a remote control. This process may involve entering a pairing code or following a series of steps on the TV screen.
Test the remote control: Once the pairing process is complete, test the LG remote control to see if it works with the Xfinity Flex box. Try navigating the menu, changing channels, adjusting volume, and performing other functions to ensure proper functionality.
If the LG remote control does not work with the Xfinity Flex box or if the pairing process is unsuccessful, it is recommended to use the original remote control that came with the Flex box or consider purchasing a universal remote control that is compatible with the Xfinity Flex box. Universal remote controls are designed to work with multiple devices and usually come with instructions for programming them to work with specific devices.
Remember to consult the user manuals of both the LG remote control and the Xfinity Flex box for specific instructions and contact customer support if you encounter any difficulties during the pairing process.
* Circuit breaker on main control box is tripped * Fuse blown (check fuse in main control box assembly). * Incorrect polarity at battery terminals * Dead batteries. * Charging cable is still connected to charging receptacle * One of the cable connections at the main control box is loose. * Control connection cable disconnected * Broken key switch * Throttle stuck fully open * Throttle control potentiometer broken. * Speed potentiometer broken * Battery voltage too low. * Faulty charging cable. * Charger not working. * Charging circuitry in main control box assembly not working
If these check OK, the problem is likely to in the control connection cable or upper control box Verify that the upper control box is getting 24V. (Blue wire on red connector.)
* If the upper control box is not getting 24V, replace control connection cable
* If the upper control box is getting 24V, check key switch operation and verify wiring in the upper control box. Trace voltage from keyswitch on to find where the problem occurs. (Replace upper control box if necessary.)
* Charge batteries with a 12V charger or replace if necessary.
* Ohm test the charging cable - replace if necessary.
* Test scooter with a different charger, if new charger works, replace charger.
* Check wiring in main control box assembly - replace in line relay if necessary * If batteries, charger, and all wiring is good, replace controller PCB. (Note the model number for the PCB, for example 1208-2330.)
This is because the remote may got resetted which have been programmed with the cable box.
So please reprogramme the remote with the cable box.It will work.
click the button on the front of the 360 console... which is to the
right of the memory slots... when the ring of light is spinning around
click the button on the top of the controller... it will then connect
to that system. There after it will always look for that system. so if
you want to connect to a new system you push the button on the front of
the system and then the button on top of the controller.....
there is a control box for the cruise control behind the glove box . You can remove the cover by pushing in from both sides of the glove box door . the control box will be just inside the glove box to the top. it simply unplugs. any junk yard with an aerostar or ranger or explorer will have one of these control boxes fairly cheap. these control boxes are commonly known to just quit workingand are a very easy fix.
Had one doing similar recently, and after a thunder & lightning storm. Nothing worked, but kept blowing 2 amp fuse in thermostat, when anything tried, heat or cool. Pulled plastic control box down from inside upper unit (AC) made sure breaker was off, took of plastic cover and smelled inside, and could smell burnt plastic smell. Replaced, control box, that got fan only working. Tried another thermostat , everything worked as it should. Turns out the lightning, or power surge, or whatever, shorted out the thermostat, and control box at same time.
×