Question about Car Audio & Video

Open Question

Mondeo MK4 - radio CD6000 removal ?

I would like to connect Nokia hands free CK-300 to radio CD6000 in my new Mondeo MK4 but I do not know how to remove radio from central console. Could explain how to disassemble and remove radio, please ?

Posted by on

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Factory system wont play with aftermarket head unit

It is probably set up where you cannot have a aftermarket radio or you might need a new radio wire kit to fit to the factory.

Feb 27, 2014 | Nakamichi Lexus Amplifier 1993-95 Gs 300...

1 Answer

I need to take the radio out

Radios are held in place by a number of manufacturers' tricks. Usually, if you can remove the decorative panel around the radio (just gentle pulls), there will be one or two tiny slots on the sides of the radio where a removal tool can be inserted to free the radio. You might be able to insert a thin bladed screw driver or knife far enough to release the radio. Without the tools (generally two) you'll have to do one side at a time. Of course, your dealer or an electronics store will have the tools and can remove the radio for you--for a fee. Or are you planning to steal somebody's radio?

Mar 24, 2013 | Car Audio & Video

1 Answer

Rockford fosgate p 300-1 amp will not turn on

plug your ground, battery, and remote wires only and see if it turns on when you turn your radio on, if not it must have blown. wiggle or move the connection block(where your wires are connected) and see if it tries to turn on. if so, your leads need to be re-soldered since they tend to go cold(they're not making good contact). But again, if that does not help, then your amp is gone.

Mar 18, 2010 | Rockford Fosgate P3001 Car Audio Amplifier

1 Answer

How do i install it it was a hand me down with no instructions

in general

the positive terminal is connected to the positive of the battery

the negative terminal is connected to a metal grounding point on the car ( find a metal spot on the car to connect the negative terminal of amplifier)(do not connect it to the negative side of the battery)

the remote terminal connects to either the remote line from the back of the radio blue and white wire

if the radio does not have a remote wire then use the red wire which is the acc (check this against your car wiring)

the speakers are simple connect the positive of radio to positive terminal ect

and the input comes from the radio as a phono jack connect that to the input of the input of the amplifier right left ect ect also if the radio has only left and right then you need a splitter for the phono cable because your amp is 4 channel

if the radio does not have phono jacks then you need to take the output that usually goes to the speakers and route them to the amp and attach pho no jacks on them

Jan 10, 2010 | Alpine MRV-F357 Car Audio Amplifier

1 Answer

Cant get radio out of safe mode on the 300 seires

Press ON Button and AS Button at the same time and leave SWITCHED ON....UNDISTURBED for as long as it takes to automatically reset itself.

Make sure you have the correct code.

If not then



Oct 12, 2009 | Blaupunkt THA125PNP 300 watts RMS x 1 at 2...

1 Answer

Connecting amp to stock radio in a 2010 carolla and need to know what wire is remote turn on lead

There is no remote turn on lead on a factory radio. The way the shops do it is to run the remote wire to your radio fuse which turns on/off with the ignitin. If you really wanted to know you can use a volt meter but it will still turn on/off with the ignition but takes a lot longer to find plus you have to remove the radio!!

Sep 07, 2009 | Car Audio & Video

1 Answer

Wiper stopped working

Ouch, what a pain. Silly question, but did you check the polarity of the battery? The other thing to check would be fuses. You have to watch out when you connect the battery terminal, that spark can cause damage. It is best to use a resistor to prevent the spark. Those 2 things are really the only things I can think of.

Nov 11, 2008 | Car Audio & Video

1 Answer

2005/2006 ford mondeo sony 6cd audio player

you can use what is called a line level converter, which taps into your speakers to convert the signal to rca cables. that is about all i can think of since i don't know the model number of the cd player

Aug 17, 2008 | Car Audio & Video

3 Answers

Blaupunkt 300 car radio & cassette

I need a better model number so that I can help you. "Car 300" didn't find anything do you see a model number or name?

Jun 11, 2008 | Car Audio & Video

2 Answers

Ford Mondeo car radio is locked

The dealer needs to help you with this. This is part of the theft protection system built into many new cars. In most cases, only the dealer can turn it back on.

Dec 21, 2007 | Car Audio & Video

Not finding what you are looking for?
Car Audio & Video Logo

Related Topics:

1,136 people viewed this question

Ask a Question

Usually answered in minutes!

Top Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

4724 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers


Level 3 Expert

63801 Answers

Are you a Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides