Question about Frigidaire ATF6000ES Front Load Washer

1 Answer

AFT 6700 - Brand new unit just dropped off code 31 in the display.

Brand new unit just dropped off by Sears, the washer has a 31 in the display and a buzzing sound when you press any button. The technician did not know what to do. Please help it will be 5 days before a Sears tech can come out.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 876 Answers

The problem with attempting repair on a new machine is that it can void the warranty. I'm sorry. You must be frustrated.

Posted on Aug 13, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kenmore elite E3t F11 error code


The "F11" fault code will display if the Motor Control Unit (MCU) has an internal failure; repeating under or over voltage, or over current conditions. If failure occurs during high speed spin the door unlocks after 3 minutes. The MCU (Motor Control Unit) is located beside the motor. See images below. Key #13 is the CCU and key #1 is the MCU.

The CCU (Central Control Unit) is located under the top along the side panel.

I recommend checking for loose wire connections at the MCU, CCU and motor. If you do not get any motor action at all, the MCU has likely failed.NOTE: Disconnect the power cord from the power source before removing the top and lower access panel. I recommend calling a service technician to diagnose and repair your washer.

Parts can be looked up and ordered at Sears PartsDirect

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website:Sears Home Services .

  • image4754382622159242732img-th.jpg
  • image8864687139589246201img-th.jpg

Dec 16, 2012 | Kenmore Elite 45986 Front Load Washer

2 Answers

E 39 message


http://appliancejunk.com/ge/washer/31-9135.pdf
above is your service manual, this will tell you all about your error codes and what to do.

May 11, 2010 | GE Energy Star WCVH6260F Front Load Washer

1 Answer

I have a 4 year old Kenmore 417.44082400 front load washer. The support leg on the right side the sides up and down to control the drum, broke. This caused the drum to beat the **** out of most of the...


Hi,

Sorry to hear about the issue you are having, the source code 417 refers to Frigidaire.

If the unit has the Kenmore name on it is built to specifications that are dictated by Sears, the manufacture sells the unit to Sears with no warranty. The warranty is supplied by Kenmore Brand. You will have better luck in my experience going up the Sears chain than the Frigidaire chain.

Hope this helps.

Apr 19, 2010 | Kenmore 44042 Front Load Washer

2 Answers

Sears kenmore washer 110.42822200 error code sud


SUD- Suds lock (Overdose of detergent detected during the wash cycle, or the actual brand is a non HE type)

The Motor Control Unit senses a suds lock condition by analyzing the current draw on the drive motor. If "Sud" is displayed a potential Suds Lock is detected. This may signify a bad pump, an extra heavy load, excessive detergent, or excessive suds.

Possible Causes / Procedure


• If too much detergent was used:

A. Run the unit through a Rinse/Spin cycle.
B. Run a Normal cycle without adding any detergent.

This should clear the unit of the excess detergent. If the problem persist, follow this check list below.

1. Check the drain hose and make sure it is not plugged or kinked.
2. Unplug washer or disconnect power.
3. Check wire harness connections to the drain pump, pressure switch, and Central Control Unit (CCU).
4. Check/clean drain pump filter of foreign objects.
5. Plug in washer or reconnect power.
6. Check drain pump.
7. Check the pressure switch.
8. Verify CCU operation by running a Diagnostic test or any cycle.

Press PAUSE/CANCEL twice to clear the display.

Dec 07, 2009 | Kenmore Washing Machines

1 Answer

Whirlpool Duet Front loader mdl WFW8300SW00 will not start


I had a variety of error codes show up on my duet, and I'm not sure but I seem to recall a 31, but the most constant was 02. I took off the front cover, pulled the white plug out from the unit, put a bucket under it, unscrewed it and drained it. It may be the MCU is having problems because the washer got plugged up. 

Apr 23, 2009 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Kenmore he2plus


Being your local Sears repair man, I feel your pain. I also hate telling people that they will have to replace a very expensive board like that, but unfortunatly, that F1 code is usually a death sentence, especially to that model. try this, sometimes you can get lucky. Unplug the machine for about 10 minutes, then plug it back in. Thats about the only way you can "reset" the unit. You can also try to run a diagnostic test. Push and hold any button (besides the start,power, or cancel) for 3-5 seconds, then let go for 3-5 seconds, then push and hold same button again for 3-5 seconds, repeat this procedure until 88 displays on the control (or all lights come on on non-display models). If you have a display, it will read to you all failure codes (you will have to push the same button you used in the diagnostic start to move through all codes), then unit will start diagnostic tests when all codes have been retrived. If you have a non-display model, you will need the tech sheet (located behind the bottom panel or inside the machine on one side in an envolope). Each light will come on displaying a certian code, which you will then have to read the tech sheet to match the light configuration to its coresponding code. Wow, i think I have a headache, do it a couple times a day. If it is your board, one recomendation, check EBAY or online sales stores. They are a ton cheaper, and you can change the board easily yourself. Remove the top, wire to wire to the new brd, your on your way. Good luck, and let me know how it turns out.

Nov 03, 2008 | Kenmore 43142 Front Load Washer

1 Answer

Error code


try unplugging it and plug it back in. make sure your water is on,but i think you will get a f/h code if it is water

Oct 31, 2008 | Whirlpool Duet GHW9150P Front Load Washer

3 Answers

Whirlpool Cabrio Washer Error message code F1


The following list of codes indicates a possible electronics communication problem with the washer:
Cabrio washer - F1, F2, F40, F41, F42, F50, F51, F52, F53, F54, F72
To remove the error display, press Pause/Cancel twice.
PLACEHOLDER FOR ART
If Pause/Cancel does not work:
  1. Unplug washer or disconnect power for one minute.
  2. Plug in washer or reconnect power.
  3. Re-select the cycle and press Start.
NOTE: If the error remains on the display, call for service.

Please do not forget to rate and comment about your experience with fixya today.

Aug 17, 2008 | Whirlpool Calypso GVW9959K Top Load Washer

Not finding what you are looking for?
Frigidaire ATF6000ES Front Load Washer Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Frigidaire Washing Machines Experts

Electrolux
Electrolux

Level 3 Expert

4342 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Are you a Frigidaire Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...