Question about Washing Machines

1 Answer

The water fills very slowly on the rinse cycles

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 481 Answers

The screen on the water valve needs to be cleaned. take off the water inlet hoses (from the back of the washer) and clean out the screens thoroughly WITHOUT taking them out of the valve.

Posted on Jul 04, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Water for intial fill works fine . when it goes to rinse cycle the water just dribbles in making wash time go on for ever ! whats the solution?


when you start the washer set it just on cold and see if it fills slowly,when the washer goes to rinse it just uses cold water,you could have a problem with the washer or in the house,when you run it on just cold and if it dribbles in,stop it shut down the water going to the washer,remove the cold water hose from the back of the washer,stick it in the sink or inside the washer and turn it on,if it comes out strong then you have a bad water valve on the washer,if it comes out slowly you have a bad water valve in the house and it's not the washer.hope this helps

Sep 12, 2011 | Washing Machines

1 Answer

My washer will fill with water during the wash cycle just fine, but during the rinse cycle the water just trickles in. The water lines seem to be fine. What else could be causing my problem?


usually the wash is a mix of hot and cold and the rinse is just cold, that said, it is most likely a problem with the cold water supply. check to make sure the cold water valve is all the way open and the hose isn't kinked. If those are ok turn the water supply off and remove the supply lines on the machine side, you will see a screen inside the washer that may be clogged with sediment. If so, just clean it out and put it back together. You may also want to run a wash cycle on cold only to see if it fills slowly for the wash cycle. If it does fill slowly on cold you have low pressure on the cold side.

Jan 07, 2011 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

Water comes out wash cycle good but slow at rinse cycle


do you mean filling the washer up or draining it out?i think you mean filling it up,on washers just the cold water is used to fill the washer on the rinse cycle,you can shut the water down and remove the cold water line and see if you can clean out the screen in the washer water valve,also while you have the hose off,stick it in the washer and open the valve to see how the pressure is,if it's coming out strong then the problem is in the washer and you should change the washer water valve,if it's coming out slowly then you have a problwm with the house water valve and need to change that out.let me know what you find

Aug 29, 2010 | Whirlpool LTE5243D Top Load Stacked...

2 Answers

Hi, our simpson enduro 701 washing machine does not spin back and forward in the deep rinse cycle. but operates ok and spins in spin cycle. thankyou Tina.


Hi Tina just read your posting. From the information in your posting the machine fills, then when the machine is full of water the agitator moves clockwise then anticlockwise until it gets to the rinse cycle then drains the water ,then it fills for the rinse cycle but does not move the agitator in the rinse cycle.Then it drains and spins the clothes dry .Is this assessment of your posting correct.If it is not 100% correct please reply to tell me what the machine is doing or not doing.If it is correct then the problem with your machine is the control board.Is your model the electronic one with the push buttons?Looking forward to your reply.

Jun 26, 2010 | Washing Machines

1 Answer

I have a Miele W1918 washer which has worked perfectly for a decade. Now there is not enough water to fill the tub during the first 'rinse' phase of normal cycles or the 'separate rinse' cycle. The machine...


I have exactly the same problem. I am currently getting around the issue by letting the machine do the washing then at the end of that cycle do a manual rinse cycle.

Jun 04, 2010 | Miele Novotronic W1918A Front Load Washer

1 Answer

The water fills very slowly on rinse


You probably have a cold inlet valve with restricted flow, either because the filter on the inlet valve is clogged or because the cold valve is failing......If you wash on "warm" you have both hot and cold water mixed. On rinse there is probably only cold water used....Check water flow for HOT and COLD settings and you'll probably see the difference...Good luck...Nomess

May 23, 2010 | Whirlpool LSR5132PQ Top Load Washer

1 Answer

My Kenmore washing machine trickles water out very slowly during the rinse cycle only


Hi, Remove the inlet hoses and clean out the screens inside the inlet valve. Most of the time it is the cold water that gets plugged up. Because you state the rinse cycle is filling slow, I believe the cold is your problem.
Please let me know if this helps or if I can assist you further.

Vic

Jul 11, 2009 | Whirlpool LSR8433K Top Load Washer

1 Answer

Kenmore washer. At rinse cycle only, water fills very slowly.


For low water volume - or "Trickling" effect...

1. Turn off the water supply to both hoses.
2. Remove hoses (one at a time so you don't get them confused)
3. On the washer side - look for a removeable screen inside wher you just removed the hose.
4. Using a small screwdriver - pop out the screen and reverse-flush it/clean it. It will likely be full of sediment and calcium deposits from your pipes.
5. Replace the inlet screens.
6. Re-fit the hose to the machine.
7. Turn on water supply valves.
8. re-try.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Apr 06, 2009 | Kenmore Washing Machines

1 Answer

G e washer fills slow on 2nd rinse


check volts at water valve in first rinse ..note that ... when in 2ed rinse check volts to w. valve and see if theres any difference in volts to valve... also compare the water pressure coming in washer ... how much pressure difference.. lot, little ? generally water valves work or dont work in all cycles ,,,this a new one for me post your results

Sep 01, 2007 | Washing Machines

1 Answer

Rinse cycle doesnt work


the humming noise is probably the cold valve operating but no water. check tap not turned off. slowly loosen cold water feed and check if water present

May 02, 2007 | Kenmore 3.2 cu. ft. Plus Top Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

297 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

yadayada
yadayada

Level 3 Expert

70374 Answers

Brad Brown

Level 3 Expert

15119 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...