Question about Onkyo Audio Players & Recorders

3 Answers

Onkyo AV Receiver TX-SR503 While sleeping with earphones connected, the receiver shut down and the standby light blinked. I unplugged the power cord, reconnected power and the receiver shut down immediately after turning power on.

Posted by on

  • kenankrebs Jul 03, 2008

    I have operated this receiver for over 2 1/2 yrs in this location for long periods of on time. Last nights operation was at a very low power level (10%). Is over-heating likely now. If it is, what is the the likely damage and is repair cost effective.

×

3 Answers

  • Official Brand Answer
  • 305 Answers

Please contact our Parts & Services Dept at the number listed below during normal business hours Monday-Friday 9am-5pm EST ; or via email at parts@us.onkyo.com. They can be contacted at 201-785-2600, option # 4 for Parts & Services as they can further assist you regarding warranty and service issues. You will need to speak with the Parts & Services/ Warranty department for any servicing options or resolutions available for your issue.

Posted on Apr 17, 2015

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 3,422 Answers

HI,

Did you try reseting it?There must be a reset button at the back of your reciever.

Posted on Jul 03, 2008

  • Priya darshan Jul 03, 2008

    Turn the reciever on, set it to an non-functioning channel, then
    hold down the VCR/DRV button and then press the standby/on button. This should clear it.

    Please don't forget to rate or accept the solution.


×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 6,487 Answers

Have you provided adequate ventilation?
May be your receiver is running hot and when there is loud volume it is obviously getting overloaded. There are no fans inside 674, the only way to provide good ventilation is to keep the top of receiver clear for atleast 6 to 8 inches.

Hope that helps.....

Posted on Jul 03, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My onkyo HT RC330 will not power up at all. Have had problems past couple of months with starting it but if you played around with swith it would start. Now nothing.


Try resetting the AV receiver To reset the AV receiver to its factory defaults, turn it on and, while holding down VCR/DVR, press 8 ON/STANDBY. "Clear" will appear on the display and the AV receiver will enter Standby mode.

It is possible that the protection circuitry has been activated. Remove the power cord from the wall.. Disconnect all speaker cables and input sources, and then leave the AV receiver with its power cord disconnected for 1 hour. After that, reconnect only the power cord and set the volume to maximum. If the AV receiver stays on, set then the volume to minimum, disconnect the power cord, and reconnect your speakers and input sources. If the AV receiver turns off when you set the volume to maximum, disconnect the power cord, and contact your dealer.

If the standby light is lit it and the unit will not boot it is most likely that the protection circuit has been activated. If there is no standby light then check the fuses. These units check that the power supplies are operating near specification. If a capacitor or resistor in the circuit, or a broken solder connection the unit will shut down. Because of the temperature the thermal cycling around the power supplies a broken solder joint can occur. This will make for an intermittent operation.

Hope this helps.
26289825-owoa52fq3dbvw0lom3ojbzgr-3-0.jpg Failed resistor or capacitor


26289825-owoa52fq3dbvw0lom3ojbzgr-3-2.jpg

26289825-owoa52fq3dbvw0lom3ojbzgr-3-5.jpg

Sep 23, 2016 | Onkyo Ht-rc330 5.1-channel Home Theater...

1 Answer

Onyko tx nr616 receiver keeps shutting off. Only stays on for approximately 3 seconds. Can you help?


The amp protection circuit has been activated. Remove the power cord from the wall outlet immediately. Disconnect all speaker cables and input sources, and leave the AV receiver with its power cord disconnected for 1 hour. After that, reconnect the power cord and reconnect an input and a pair of speaker wires onto the unit. If the receiver still does not turn on than you will have to bring it in for service. Turn up the volume and if the receiver doesn't shut down, power off the receiver and add another pair of speakers. Power up the unit again and turn up the volume. If it doesn't shut down, power off the unit again. Now connect all your input sources and turn on your receiver. If the unit shuts down again, your unit will need to be further serviced at an authorized Onkyo service center.

Sep 30, 2014 | Onkyo Tx-nr616 7.2 Thx Certified Network...

1 Answer

Onkyo ht-rc180 standby light blinks will not start.i tryed factory reset, still blinks


The amp protection circuit has been activated. Remove the power cord from the wall outlet immediately. Disconnect all speaker cables and input sources, and leave the AV receiver with its power cord disconnected for 1 hour. After that, reconnect the power cord and reconnect an input and a pair of speaker wires onto the unit. If the receiver still does not turn on than you will have to bring it in for service. Turn up the volume and if the receiver doesn't shut down, power off the receiver and add another pair of speakers. Power up the unit again and turn up the volume. If it doesn't shut down, power off the unit again. Now connect all your input sources and turn on your receiver. If the unit shuts down again, your unit will need to be further serviced at an authorized Onkyo service center.

Sep 24, 2014 | Onkyo Ht-Rc180 7.2-Channel A/V Surround...

1 Answer

Our dvd has no sound we think we need to reset it but do not know how


Any digital source must have its input assigned (page 31 of the manual). The DVD player has a role in this, too. Try another cable or input.

If you have the manual, crack it open and follow it's advice for your symptom. Then look at every indicator and control to evaluate how it fits into your desired listening experience. UNDERSTAND the receiver or you will forever have issues with losing the 'sound' because a seldom-used control got touched by mistake.

Register and download the manual for free at retrevo.com

http://www.retrevo.com/support/Onkyo-TX-SR503-Receivers-manual/id/365ag216/t/2/

If you still feel a reset is necessary look at page 57 or search the document for "factory defaults".

To reset the AV receiver to its factory defaults, turn it on and, while holding down the [VIDEO 1] button,

press the [STANDBY/ON] button. "Clear" will appear on the display and the AV receiver will enter
Standby mode.

Jun 25, 2011 | Onkyo TX-SR503 Receiver

1 Answer

Stanby light for zone 3 is on , cant shut down the volume, i need to reset the receiver, any steps i have to follow?


Hi,

To reset the Onkyo TX NR3007 AV receiver to its factory defaults, turn it on and, while holding down the [VCR/DVR] button, press the [ON/STANDBY] button. “Clear” will appear on the display and the AV receiver will enter Standby mode.
Thanks for using Fixya.
Good Luck and have a nice day.

May 27, 2010 | Onkyo TXNR3007 91 Channels Receiver

1 Answer

SHUTS DOWN AFTER 1 HOUR w/ standby light blinking.


Exactly an hour? Is the Sleep Timer enabled?

Nov 28, 2009 | Onkyo TX-SR606 Receiver

1 Answer

Blinking standby button


Hi...1st off ...make sure all the speakers are connected at both ends.
2nd..buy a new cat..one that doesnt drool.
If it's still stays in Stdby after checking speakers, It might have blown an internal fuse cause thats where those darn stereo people put them now.

Jan 09, 2009 | Onkyo TX-SR605 Receiver

1 Answer

Amp protection mode


Disconnect everything from the amp except the power cord, then power on the amp. If the receiver still shuts down, your problem is inside the case and unless you can perform electronic repair yourself you will probably need to take it in for service. If it does not shut down with nothing connected, power it off, connect one speaker or component and power on again. Repeat the process until the amp shuts down and you may have found the bad speaker or other component.

Jan 01, 2009 | Onkyo TX-SR503 Receiver

3 Answers

Onkyo HT-R501 7.1 reciever issues


i have the same problem with a onkyo tx ds494

Jan 05, 2008 | Onkyo TX-SR605 Receiver

Not finding what you are looking for?
Audio Players & Recorders Logo

Related Topics:

242 people viewed this question

Ask a Question

Usually answered in minutes!

Top Onkyo Audio Players & Recorders Experts

Dennis McCollum

Level 2 Expert

137 Answers

 Grubhead
Grubhead

Level 3 Expert

4861 Answers

The Knight
The Knight

Level 3 Expert

72670 Answers

Are you an Onkyo Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...