Question about Kodak EASYSHARE 5500 All-In-One InkJet Printer

1 Answer

Scanner The scanner sticks three quarters of the way so it will not scanfax or copy just started all of the sudden two days ago

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 96 Answers

Download the newest firmware from www.kodak.com/ . Go to the downloads and drivers section and chose your respective printer. If the newest firmware does now work, you will need a replacement printer.

Posted on Jul 15, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a HP Deskjet 2120 all-in one Printer, I pressed Copy, then suddenly the red Resume button flashes and the printer stops working. It seems that there is a software problem. Can you help resolve


With out PC also we can able to take copy & fax. It's not the issue with software, might be flat bed scanner assembly faulty or internal parts of flatbed scanner assm like optical scanner, scanner cable or motor..Check these & replace faulty part..

Dec 20, 2011 | HP Office Equipment & Supplies

1 Answer

CARRIAGE ERROR It cant send fax and copy


I AM A AMATOR REPAIRMAN OF COMPUTER HARDWARE. A FEW DAYS AGO I SOLVED THIS PROBLEM ON PRINTER PANASONIC KX-FLB802 BY SERVICING ITS SCANNER. OPEN SCANNER PART AND PUT SILICON OIL ON WITHE MOVING PART OF IT.
TOP AND END OF TWO SIDES ARE TWO WITHE PLASTIC PARTS. IT SOLVED BY OILING. THE END.
SORRY BECAUSE BAD ENGLISH.

Dec 20, 2010 | Panasonic KX-FLB801 All-In-One Laser...

1 Answer

My ESP-3 printer has worked well since I bought it a year ago. Two days ago I was printing off a bulk letter, and things went suddenly uncooperative. USB lead OK - new cartridges - control panel checked...


Hi and welcome to FixYa!

Well reinstalling the printer driver is really recommendable. But before reinstallation I strongly suggest that you remove the usb cable then uninstall existing driver. After uninstalling the driver please restart the pc then start the installation without the usb cord unless being asked.

Hope this helps and thank you for using FixYa! Have a good one!

Dec 01, 2010 | Kodak ESP 3 Multifunction Printer/ Copier/...

1 Answer

When scanning or copying on the 7310 on my Mac osX 4.11 the scans and copies have large black horizontal bands across the page. The band is randomly places and. If the scan image is good, the saved PDF...


sounds as if your scanner bulb is fualty I would suggest doing a power cycle - by removing the power cord while on wait ten seconds and plug cord back in or try a different power socket (preferbly a direct socket without any adapters connected to it)

Jan 15, 2010 | HP OfficeJet 7310 All-In-One InkJet...

1 Answer

Konica bizhub C351 copier with a C9401 error code


To you need a mechanical adjustment.
A. Adjustment of the scanner motor timing belt. This adjustment must be made the scanner motor assy has been removed,or the scanner drive cables have been rewound.
1. Remove the IR rear cover.
2.Remove 16 screws and the reinforcement frame.
3.Loosen the 3 screws that secure the scanner motor mounting bracket.
4.With the scanner drive gear set screw located on the right hand side as shown on the left,slide the scanner motor assy to the left and check that it is returned to the original position by the tension of the spring.Perform this step three times.
5.Tighten the three screws to fix the scanner motor assy into position.
B.Focus positioning of the scanner and mirrors unit. This adjustment must be made in case the scanner drive cables have been rewound
1.Slide the mirrors unit to rhe center until it is pressed up against the cutouts in the rails.
2.If the mirrors unit is not pressed up against the cutouts,loosen the adjusting screw to which red paint is applied of the mirrors unit and press the carriage up against the cutouts.Then tighten the adjusting screw.
C.Scanner position adjustment.This adjustment must be made if the scanner drive cables have been rewound,focus positioning of the scanner and mirrors unit must be completed.
1.Slide the mirrors unit to the position shown on the left.
2.Secure the scanner in the position shown on the left using the 2 scanner positioning screws.
3.Make the FD-Mag. adjustment.:
FD Mag setting range :0,990 to 1,010 in 0,001 increments.
If the specified width om the copy is less than 298,5 mm increase the settings.
If the specified width on the copy exceeds 301,5 mm decrease the settings.
Adjustment procedure:
1.Call the Tech.Rep.Mode to the screen.
2.Touch these keys in this order : Machine Adjust - IR Area.
3.Position the color chart correctly so that the original reference point is aligned with the scale.
4.Press the Start key to make a copy.
5.Check point D( D:300+/- 1,5 mm) on the image of the copy.
6.If the image falls outside the specified range,touch FD-Mag.
7.Change the setting using the up/down key.
8.Press the Start key to make another copy.
9.Check the image on the copy to see if the specifications are met.
10.Make adjustments until the specifications are met.
Good luck,please answer.

Aug 02, 2009 | Konica Minolta Office Equipment & Supplies

1 Answer

Won't copy or fax, scanner failure


Uneconomical to replace the scanner assy. sorry

Feb 17, 2009 | HP Officejet 4315 All-in-One Printer

1 Answer

Check Cables. Check Scanner Lock. Cycle Power.


the problem is the cable in the scanner's mainboard

Sep 15, 2008 | Office Equipment & Supplies

1 Answer

We have a 8825 with the scanner and the scanner display is always reading "NOT READY" I do not see the lamp turn on when we power the scanner. At first the scanner would copy somethign but the...


The printer is either performing a reset, a copy quality adjustment, or is just warming up. Any of these procedures can last for at least three minutes.

Sounds like a fuser lamp has gone bad.
For a dealer that can probably reference you for service start here.
14.8 mi Replica Business Solutions, Inc. 670 King Park Drive Billings MT N (406) 839-9228 crduncan@hughes.net

Apr 17, 2008 | Office Equipment & Supplies

1 Answer

Printing only one quarter of page when copying


Make sure by checking if your lamp scanner light when your doing a copy ??? This look like a scanner problem !

Make sure to that your glass is clean !

Feb 07, 2008 | Epson Stylus CX4600 All-In-One InkJet...

Not finding what you are looking for?
Kodak EASYSHARE 5500 All-In-One InkJet Printer Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kodak Office Equipment & Supplies Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18333 Answers

Michel Smith

Level 3 Expert

1218 Answers

Sajid Najmi
Sajid Najmi

Level 1 Expert

31 Answers

Are you a Kodak Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...