Question about D-Link Express DCS-900 Network Camera

1 Answer

Configure webcam in wan

I have prob with configure webcam in wan please help me

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Expert
  • 8,637 Answers

Normal 0 Web Camera’s have to be setup on the program they are to be used with. Just installing the camera on your computer does not set it up to broadcast on messengers or Skype.

Each program has Options that have to be setup in order for the Audio and Video to function properly.

A. Skype Setup:

After downloading and installing Skype set it up as follows:

  1. Go to TOOLS, then OPTIONS, and click on Audio Settings and set the Microphone and Speakers to the computer Audio Card.
  2. Then click on the Video Settings.
  3. The camera if installed properly will come up and show a picture.
  4. Then on the bottom of the page click on Save.

The camera and audio should function properly. Your friends and Family will now see and talk to you.

B. Yahoo Setup:

After downloading and installing Yahoo Messenger set it up as follows:

  1. Go to Messenger at the top left and click on it.
  2. Next go down to Preferences and click on it.
  3. Next Calling and Devices on the right and set the Microphone and Speakers to the computer Audio Card.
  4. Next go to the Test Audio section and (in blue writing) click on “Open the call setup assistant” and follow the instructions on the left window.

C. Windows Live Messenger:

  1. After you start Windows Live Messenger, expand the view by clicking on the square on top left next to the red X.
  2. Then on the Windows Live messenger window on the right side, click on “ “Show Menus.” And then click on “Show the Menu Bar”.
  3. Next go to the Menu Bar on right side, click on “ “Action.”
  4. Go to “TOOLS” and click “Audio and Video Setting” and follow the instructions.
NOTE: You audio and video shoud work. Enjoy.

When done both the Audio and Video will function properly so you can chat and see family or friends you are connected to.
Hope this helps. Bud

Posted on Jan 13, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can the management IP address of an ONT be configured?


ONT management IP addresses are classified as LAN-side management IP addresses and WAN-side IP addresses.
· The LAN-side management IP address can be configured. To do so, choose LAN > LAN Host Configuration from the main menu on the web page.
· The WAN-side management IP address is based on WAN port configurations.
§ If the WAN port statically obtains an IP address, the WAN-side management IP address can be configured. Ensure that the configured management IP address can communicate with the upper-layer device.
§ If the WAN port obtains an IP address in DHCP or PPPoE mode, the WAN-side management IP address can only be obtained from the DHCP server.

May 16, 2016 | Computers & Internet

Tip

How to configure a Router?


How to determine the WAN configuration or Interntet configuration of a SOHO Router?
1. Connect the computer to the Modem via Ethernet cable. Make sure you are able to going online 2. After confirming you are online. Go to Start->Run. Type "cmd" on the Run window. 3. Type "ipconfig" on the command prompt or Black window or DOS window 4. You will be getting IP address,Subnet Mask and Default Gateway
There are 4 possibilities of IP address you can get
i)Public IP address under PPP adapter. -Router has to be configured in PPPoE mode to get a WAN IP. This will require a Username and Password from ISP ii) Public IP address under PPP adapter and Private IP address under Ethernet adapter -Router has to be configured in PPPoE mode to get a WAN IP. This will require a Username and Password from ISP iii)Public IP address under Ethernet adapter -Router has to be configured in Dynamic IP or DHCP mode to get a WAN IP -If it is still not getting a WAN IP address. * Click Mac clone on the router's WAN configuration * Power-cycle modem and Router. iv)Just a Private IP address under Ethernet adapter -Router has to be configured in Dynamic IP or DHCP mode to get a WAN IP -If it is still not getting a WAN IP address. * Power-cycle Modem and router.
After determining the WAN mode, it is time to configure the Router
1. Connect the Modem to the WAN port of the router. Connect the computer to the LAN port 2. Go to Start->Run. Type "cmd" on the Run window. 3. Type "ipconfig" on the command prompt or Black window or DOS window 4. You will be getting IP address,Subnet Mask and Default Gateway. The Default Gateway will the IP address of your router 5. Open a Web browser and type http://192.168.1.1(where this is the default IP of the router. This will be different from each manufacturer) on the address bar. 6. Go to WAN settings or Internet settings and select the options based on the above mentioned possibilities

on Aug 26, 2010 | Computers & Internet

1 Answer

Dear Assistants I have a router linksys compact wirless - g broadband router. model number WRT 54GC ver. 2 and i have a problem with it I cant find anywhere the WAN MAC Adress of the Linksys What to do???...


The Linksys has a device MAC address and the router issues IP addresses to the computers that are connected to it.
There is no WAN MAC address. Your ISP issues to your cable or DSL modem an unique IP address and you connect this modem into the WAN port on the Linksys router.
You enter the routers configuration address -
http://192.168.1.1
and login and configure the router.
To secure your wireless network from unauthorized access, please click on this link and follow my instructions :-
Normal 0 http://www.fixya.com/support/r3559128-wireless_router_security

Oct 23, 2010 | Linksys WRT54GC Compact Wireless-G...

1 Answer

I wan to install my webcam but my cd rom won't


Thank you for your question.

I have searched the manufacturers website for you and have provided a link to the Driver Download Page for your Webcam.

http://www.a4tech.com/download%20driver.asp

Download the driver to your Desktop and Unzip the file, when installing the Webcam and it asks for the Driver, "point" it to the downloaded/unzipped file.

Could you please take a moment to vote as this assists me in assessing whether my answers are on the right track.

Kind regards

Jul 20, 2010 | A4tech PK-7ma Flexi Webcam

1 Answer

PROB WITH WEBCAM


Go into your devices manager and make sure the imaging devices(webcam) drivrs are installed.You may have to uninstall them and reboot your laptop to reload new drivers,it should do that automatically when you reboot

Apr 12, 2010 | Tablets & eReaders

1 Answer

Router page not available offline


You don't connect to WAN port, you need to connect it to one of the switch ports. The wan is strictly for modem configuration

Dec 17, 2009 | D-Link Dlink DI-514 Air Wireless 2.4 GHz...

1 Answer

Webcam prob.


how to solve this problem

Mar 10, 2009 | GE Computers & Internet

1 Answer

Cant get my router to work


Connect the computer to LAN port one of the router using an Ethernet cable, access the configuration page (ie 192.168.1.254), configure the router as Dynamic IP, Configure the wireless network as (WEP or WPA), Check the IP address of the WAN section.

Note: If you have an IP address to the WAN section the Internet connection is working, Connect through the wireless network by finding the wireless network name was been created to the router.

Mar 09, 2009 | Belkin Wireless G Plus MIMO (F5D9230-4)...

1 Answer

WAN settings


The WAN settings should be configured by Verizon personnel only. If you reset the VDI-604 or VDI-624 to factory defaults, you will need to contact Verizon to reconfigure your WAN settings.

Feb 16, 2006 | D-Link AirPlus Xtreme Super-G DI-624...

1 Answer

WAN settings


The WAN settings should be configured by Verizon personnel only. If you reset the VDI-604 or VDI-624 to factory defaults, you will need to contact Verizon to reconfigure your WAN settings.

Feb 16, 2006 | D-Link Express EtherNetwork DI-604 Router

Not finding what you are looking for?
D-Link Express DCS-900 Network Camera Logo

Related Topics:

267 people viewed this question

Ask a Question

Usually answered in minutes!

Top D-Link Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2260 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18381 Answers

Mike

Level 3 Expert

4334 Answers

Are you a D-Link Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...