Question about Samsung Standard (CRT) Televisions

1 Answer

Burnt out resistor

C430 was s/c (burnt) in LOP stage and the resistor R420 was also burnt beyond recognition. It looks like it's the feed for the line drive voltage. Can you possibly tell me the value of the resistor as I do not have a manual. Thanks in anticipation...Steve

Posted by on

  • stevepatmore Jul 03, 2008

    Sorry I dont know the chassis no. but the model no. is DTP 28A8 S

  • Jaime Hernandez May 11, 2010

    Could you please provide the model number and chassis number if possible?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,267 Answers

I was not able to find a free service manual download. Here's is a site that has the service manual but is a pay site. click here.

Posted on Jul 03, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to solve horizontal lines on a CRT TV monitor and what could be the possible courses for it


Monitor horizontal lines problems usually caused by a defective vertical output/driver ic. A missing supply voltage to the vertical output ic may caused similar faults which is one horizontal line across the display. Dry joints and missing vertical output pulse from vertical oscillator ic also could contribute the same symptom. If you discovered that the protection resistor (usually from 1 to 4.7 ohm) open circuit or burnt, then replacing it won't solve the problem. The resistor burnt or open circuit was due to a short in the vertical output ic. Thus you have to replace the vertical output ic and the burnt resistor together before you switch on the monitor.

Jun 12, 2015 | Standard (CRT) Televisions

1 Answer

Dead set. Smoke came over the TV.


The smoke is usually came from burnt resistor cause of short circuit or shorted parts inside..

Try to open the back cover of your TV and look at the resistor burnt..and replace it..also try to find shorted parts connected to burnt resistor or behind it..

Oct 22, 2011 | Sony FD Trinitron WEGA KV-36FS120 36" TV

1 Answer

Sony trinitron


The smoke is usually came from burnt resistor cause of short circuit or shorted parts inside..

Try to open the back cover of your TV and look at the resistor burnt..and replace it..also try to find shorted parts connected to burnt resistor or behind it..
  • By bugoy31_1.jpgbonifacio gomez posted now
    bonifacio gomez Level 2
    bugoy31_1.jpg
    • 654 Solutions
    • 380 Score

Oct 22, 2011 | Sony FD Trinitron WEGA KV-36FS120 36" TV

1 Answer

LINE STAGE PC BOARD BURNT SANSUI SV29281


A good tech could probably fix that, did it burn a hole or otherwise carbonize the phenolic PC board material? If so replace the board.

You can only get that board directly from Sansui or one of their distributors. If your set is out of production (more than a couple of years old) there is a good chance that the board is no longer available likely get that board from Sansui, there will be no generic replacement for that. There is a safety factor involved here.

If you can get the board then replace it and see what happens. Hopefully it will happily give your more years of service.


Jun 24, 2010 | Standard (CRT) Televisions

1 Answer

Burnt Resistor


There are LIKELY other bad components that caused this. Resistors USUALLY don't fail on their own.

Jan 30, 2010 | Toshiba 32A33 32" TV

2 Answers

My TV picture has collapsed to a single horizontal line


If it is an standar analog tv, I'm sorry to tell you but, is time to get a new one.

Dec 05, 2009 | Panasonic Standard (CRT) Televisions

1 Answer

Colored lines through my tv


Convergence problem; requires 2 STK392-110 ICs and possibly burnt resistors replaced.

Apr 26, 2008 | Hitachi 43FDX01B TV

1 Answer

Magnavox resistor problem


The CRT board is the one that connects to the back of the CRT.
Follow the 200VDC line to locate the burnt resistor, is normally a low value fuse resistor.

Apr 15, 2008 | Philips Magnavox 27MS343S 27" TV

1 Answer

Green screen


if it is "C514" it is capacitor. maybe the green section from the crt board is dead, try to test the transistor from its circuit or resolder it.

Jan 18, 2008 | RCA 20V500T 20" TV

1 Answer

Lightning Strike, Plz Help!


Hi. The red line on ICS is quite normal it does not mean the part has failed. To be honest in most cases if a tv has been hit by strike it is a right off & scapped. What I suggest is to remove the main pcb & power supply pcb if its seperate & inspect the print side of pcb for signs of arcing tracking or burnt track. Repair any damaged track by cleaning off the coating to get at clean copper then solder wire accros to bridge the damage. Check the power supply resistors diodes transistors look carefully for any burnt components or components which are physicaly damaged. Check the line output transistor this will be near the large transformer with a thick red ht lead going up to the crt. Check all the components you can in the line stage look at all the ICS to ensure none of them have holes in them or have blown apart. Hopefully you find some or one if your very lucky that is damaged replace it & try your tv.

Sep 23, 2007 | Toshiba CZ36V61 TV

Not finding what you are looking for?
Standard (CRT) Televisions Logo

Related Topics:

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top Samsung Standard (CRT) Televisions Experts

The Knight
The Knight

Level 3 Expert

68352 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Jaime Hernandez

Level 3 Expert

2267 Answers

Are you a Samsung Standard (CRT) Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...