Question about Maytag MER6769 Gemini Electric Kitchen Range

1 Answer

The oven F9s and will not heat> How much for a service call and to fix. can all charges be applied to a new stove? Thank you

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 734 Answers

F9 code usually means that the temp sensor in your oven is at fault . The electronic oven control is sensing a fault with that part. that part is pretty simple to replace Call a local service company with model and serial # they should be able to get the part for you ! Temp sensors are usualy located inside the oven in the upper left hand corner 2 screws hold it in place .It pulls out and has a conector on the back that unplugs.

Posted on Nov 30, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

220 stove has nothing hooked up to the neutral


TURN OFF POWER TO THE STOVE OR UNPLUG IT IMMEDIATELY BEFORE TOUCHING **ANYTHING**. I need the make/model of your unit to help you accurately. HOWEVER, the first thing you need to do is(and this applies if I'm interpreting you correctly)replace the power cord--it will be connected to the terminal block--on the vast majority of ovens, you have a left-hand terminal, generally known as L1(a power wire), a center terminal(*normally* the neutral connection), and then the right-hand terminal, generally known as L2(2nd hot supply wire). Take a picture of the AC outlet so you can purchase the correct power cable for your stove. Also, take a picture of the terminal block in the rear of the stove just to make sure. I'm assuming that the wires are all connected in the stove but the neutral wire is either broken or missing from the power cord. Due to how most ovens operate, THIS IS A VERY DANGEROUS CONDITION. When the unit is plugged in, even though the oven is off, there is still 120v applied to the heating elements. When you turn on the oven, instead of being connected to a ground, the other side of the heating elements are simply connected to 120v from the other side of the panel, adding up to 240v and the elements heat up. I hope this helps you!

Aug 13, 2015 | Kitchen Ranges

1 Answer

I have a Garland Stove and Oven. The oven is not working right.


Hi there, most of the newer unit parts are available still, but not seeing it makes it hard to guarantee. I would advise calling a Factory Authorized Servicer in your area, having a problem with gas entering the oven, and not igniting is a serious problem, and it sounds like the pilot is lit in the oven, but could be malfunctioning.
Here is the telephone for Garland: Tel: 1.800.424.2411.
They can recommend someone in your area, or check your local phone book, for Restaurant repair companies, and contact them.
Hope that helps, and thank you.

Feb 04, 2009 | Garland H283 Gas Kitchen Range

2 Answers

Stove won't heat


Oven was working, I had it on pre-heat, then I turned on the stove top, but the burners won't heat. When I turn on the stove top the stove makes a short BUZZ noise and the clock area lights up, when the burner is turned off all the lights go out. Please help, food prepared.
Thank You

Dec 02, 2008 | Frigidaire FEF336BC Electric Kitchen Range

1 Answer

Our GE Profile Oven is not heating up (stove works)


Please check here for possible troubleshooting steps:
http://www.repairclinic.com/0088_13_1.asp#Level1_2

Hope that helps! Should you have any further questions,please feel free to post them here.

P.S. - If you find that the solution/answerI provided led you to, or resulted in a fix, please close the ticket with a FixYa!rating. I would be very grateful for your show of appreciation.

Thank you for using FIXYA!

Cheers!
IrishDruid

Oct 04, 2008 | GE Spectra JGBP35 Gas Kitchen Range

1 Answer

When using the oven or especialy the broiler the outside of the stove (the part where the control panel is), right above the burner gets extremey hot so hot if you would touch it you would get a severe...


There is a vent pipe for the oven in the back usually just under the left rear burner, it is normal too get hot air there, if your drip pans are all solid you might want too change too pans that have holes in the center it should allow the top too breath a little better.

Jul 30, 2008 | Maytag Kitchen Ranges

1 Answer

Oven pilot light won't light


Part of the problem was my own ignorance about this particular Kenmore gas oven. It doesn't even have a pilot light. Instead, there is an electric heating element close to the burner which gets so hot that it ignites the gas. It seems that the heating element also doubles as a temperature sensor, so that it opens the gas valve only when the heating element is hot enough to ignite the gas. This heating element, called the "ignitor", no longer gets hot in my oven even though there is 120VAC applied to it when the oven knob is turned on. Therefore, the ignitor is defective. I ordered a new one on-line from "Appliance Parts of America" for $31.50 plus shipping, and this should fix the problem. If it does NOT, I'll add to this post.

Apr 21, 2008 | Kitchen Ranges

Not finding what you are looking for?
Maytag MER6769 Gemini Electric Kitchen Range Logo

Related Topics:

100 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Kitchen Ranges Experts

gbob59

Level 3 Expert

2963 Answers

freddyfox

Level 2 Expert

236 Answers

yadayada
yadayada

Level 3 Expert

61292 Answers

Are you a Maytag Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...