Question about Digital Cameras

1 Answer

Canon Powershot A610

Hello,

My Canon A610 is not focusing anymore. Seems the sensor is dead or can't see anything. Otherwise I can play pictures from card but it doesn't take any picture because there is no signal from the sensor. Can be fixed?
Thank you very much.

Kind regards,
Radu
M: +44(0)7872834832

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 101 Answers

The CCD ribbon cable probably came loose, you will probably have to send it to Canon, This happened to my A70, and there was a recall on the CCD design, they replaced it for free, they might do the same for you.

Posted on Jul 02, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When I push down on the button to take a picture, nothing happens


If you are too close to a subject the camera will not focus and therefore will not release the shutter.

May 19, 2014 | Canon PowerShot A610 Digital Camera

1 Answer

Camera has a black LED screen when in the shooting mode. If a picture is taken it also is black. Previous pictures can still be viewed from the memory stix.


probably ur sensor is dead or there is dirt and moisture accumulation over ur sensor.... it is a mechanical cover and the dirt-moisture ghlue is preventing it from opening and stimulating the sensor. take it to prf repairer and get the dirt removed.

i had the same problem with my POWERSHOT A610

Dec 18, 2009 | Canon PowerShot G10 Digital Camera

1 Answer

My canon powershot a610 has a black screen


Try the solution posted by frozen80 at http://www.fixya.com/support/t295396-canon_s2_black_screen. It fixed my Canon PowerShot A610 black screen (closed diaphragm) problem.

Nov 28, 2009 | Canon PowerShot A610 Digital Camera

1 Answer

Canon Powershot a610 dropped, lens stuck half way, won't move, gives E18 whenever one puts it in the mode to take a picture, no view through lens. Is the camera toast?


Hello there,
The E18 error is related to the LENS not able to retract fully. If it is still under warranty, I would advise you bring it to the nearest service center. This is to avoid further damages. Otherwise, you can try a few things below.
There are a couple of things you can do.
1. Turn it on and then off. Spray canned air around the lens.
If trick 1 will not work out, try this.
2. Make sure the battery is fully charged. Turn on the camera and then give it a couple of firm whacks on the side. Make sure nothing is blocking the lens and wait for it to fully retract.
Let me know how it goes.

Nov 19, 2009 | Canon PowerShot A610 Digital Camera

1 Answer

Images have pink overlay


I had the same problem with my camera, suddenly the LCD and picture shows some pink image overlay bands on the top usually. When focusing the bands sometimes disappear. But they always shows on image as on the LCD. Canon seems to fix this problem as goodwill (guarantee is not valid anymore) so I sent my camera to service for this. Hope they accept this otherwise it is broken, LCD common problem. (Solution or same problem we will see)

Dec 01, 2008 | Canon PowerShot S500 IXUS 500 Digital...

5 Answers

Hello, My Canon A610 is not focusing anymore. Seems the sensor is dead or can't see anything. Otherwise I can play pictures from card but it doesn't take any picture because there is no signal from the...


Hello!!

Firstly switch off the camera
press and hold the ok button and turn the camera on and off for few times
whilst keeping this button depressed

Regards
Smilemaker.

Jul 02, 2008 | Canon Digital Cameras

1 Answer

My Canon Powershot SD630



What do pictures taken at night/poor light look like ?? if they are an improvment ,
your Exposure/Auto-Light/White Balance settings may be horribly configured.

Firstly I'd try Resetting the camera to default settings by using the settings menu .
>Menu >Settings >Reset default settings

This should eliminate poor settings as a suspect for the problem.




Sep 28, 2007 | Canon PowerShot SD630 Digital ELPH / IXUS...

3 Answers

Replacing a part on my Canon PowerShot A610 Digital Camera


you will need a #0 screwdriver. 1. remove the screws on the sides two on one side three under the Digital/dc in / av out 2. removed the screws from inside the battery compartment three total screws Cheers! PS these are small screws. Work in a well lit area!

Sep 08, 2007 | Canon PowerShot A610 Digital Camera

Not finding what you are looking for?
Digital Cameras Logo

Related Topics:

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Digital Cameras Experts

kakima

Level 3 Expert

96683 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Steve

Level 3 Expert

3287 Answers

Are you a Digital Camera Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...