Question about Refrigerators

1 Answer

Need advice on how to replace brandt CFA361XU freezer door seal.i have the new seal but cant remove the old one.cant see any retaing screws.and seal doesnt seem to pop out. thanks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,462 Answers

I shouldn't do it
seal is foamed in and i'v not had any success on replacing foamed in seals. applies to all makes
sorry to be negative

Posted on Jul 02, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I to replace the seal in the door?


ON SOME MODELS U MAY NEED TO TAKE APART THE DOOR IT SELF TO GET TO THE INSIDE OF SEALS, BUT MOST LIKELY IF U PULL BACK THE SEALS THEY EITHER HAVE SCREWS THAT WILL BE OBSERVABLE AND THEN REMOVED AND SOME HAVE A SLIP ON TYPE CLIP THAT CAN BE REMOVED BY SLIDING THE SEAL OUT HOPE THE PICS HELP

25064396-oj31pmt05x02zgdxjxsset5x-3-0.gif

25064396-oj31pmt05x02zgdxjxsset5x-3-2.jpg

25064396-oj31pmt05x02zgdxjxsset5x-3-5.jpg

25064396-oj31pmt05x02zgdxjxsset5x-3-9.jpg

Sep 05, 2014 | Hotpoint RTA41 Top Freezer Refrigerator

1 Answer

HOW DO I REPACE D00R SEAL


To replace your seal you'll have to remove the screws around the perimeter of the door's inner panel. Once all the screws are off separate the inner panel from the old seal and peel the seal away. It should peel away easily- if not use a Putty Knife to remove it.

Now take your new seal and "soften" it up a little by placing it in hot water for 10 minutes or so. It'll make it easier to place back in the correct position around the door since the seal was probably all twisted up and sharply folded doing shipping/storage.

Now simply lay it back in the same position the old seal was making sure there are no folds, creases or cuts in the seal. It must lay flat or it will leak all over again. Note: there is a sealant that you may want to get that's specially made for these seals to guaranty the seal gaps are filled and the seal stays in place. I use "Kitchen and Tub" Caulk when I don't have any refrigerator caulk available.

Now reassemble the door inner panel, your new seal, and the outer door all together with the screws you previously removed and you're all done.

If you need more info an excellent source is "Appliance Parts Pro". http://www.appliancepartspros.com/parts-for-frigidaire-ffu14k0dw0.html

Click on your Seal (item #1) and see the comments below that other customers asked.

Hope this helps.

Jun 27, 2014 | Frigidaire 14.1 cu. ft. Upright Freezer...

1 Answer

How do I repalace a door seal on the Kenmore refrigerator?


Remove the door makes the job easier. Using a table lay the door with door seal in the upright position. Pinch and pull the door seal over to one side to expose the door seal screws. Remove screws and gasket/ seal and install the new door seal in the reverse order.

Feb 07, 2014 | Refrigerators

2 Answers

I need to replace the rubber seal on my Hotpoint ice diamond freezer door I can't find any fixing screws on the inner door panel can I assume then that the panel clips on.


Me too, I have a Hotpoint Iced Diamond Under counter fridge that needs a new seal and i also cant see any fixings to remove it. I did read somewhere that you can't replace them you need to buy a complete new door.

Dec 14, 2010 | Hotpoint HTS16HBR Top Freezer Refrigerator

1 Answer

ICE DOOR SEAL IS LOOSE AND NOT SEALING CAUSING FROST BUILDUP


Hello,

This is the step you will use to repair your ice door seal that is loose.

There are screws under the fold of the freezer door gasket that holds the brace for the gasket in place. Lift the rubber gasket to expose the screw head, one section at a time. Just loosen the screw, and do not take it completely out.

As you loosen the screws, one section at a time, carefully remove the old gasket. At the same time, fit the new gasket into the groove. Make sure your new gasket is lined up properly.

Continue around the freezer door, unloosening the screw, taking out the old gasket and fitting the new one in.

Tighten the screws into place. This may have to be done once the entire gasket is fitted into place.

Check the seal by closing the door. You should have a nice, tight seal.

Good luck.



  • Step 4 Tighten the screws into place. This may have to be done once the entire gasket is fitted into place.

  • Read more: How to Fix a Freezer Door Seal | eHow.co.uk http://www.ehow.co.uk/how_4855248_fix-freezer-door-seal.html#ixzz0rY7rn3O8
  • Step 3 Continue around the freezer door, unloosening the screw, taking out the old gasket and fitting the new one in.
  • Step 4 Tighten the screws into place. This may have to be done once the entire gasket is fitted into place.

  • Read more: How to Fix a Freezer Door Seal | eHow.co.uk http://www.ehow.co.uk/how_4855248_fix-freezer-door-seal.html#ixzz0rY7gYaZ2
  • Step 2 As you loosen the screws, one section at a time, carefully remove the old gasket. At the same time, fit the new gasket into the groove. Make sure your new gasket is lined up properly.
  • Step 3 Continue around the freezer door, unloosening the screw, taking out the old gasket and fitting the new one in.
  • Step 4 Tighten the screws into place. This may have to be done once the entire gasket is fitted into place.
  • Step 5 fix-freezer-door-seal-1.5-120x120.jpg jQuery(document).ready(function(){ jQuery('#jsArticleStep5 span.image a:first').attr('href','http://i.ehow.com/images/a04/k5/eg/fix-freezer-door-seal-1.5-800X800.jpg'); }); Keep the gasket clean to last longer. Check the seal by closing the door. You should have a nice, tight seal.

  • Read more: How to Fix a Freezer Door Seal | eHow.co.uk http://www.ehow.co.uk/how_4855248_fix-freezer-door-seal.html#ixzz0rY7JfY8i

    Jun 22, 2010 | Refrigerators

    1 Answer

    How can I fit a bottom door seal on a Brandt dishwasher please. My dishwasher is leaking but the door seal and gaskets are intact although the sealant which held the gaskets in place has disintegrated....


    Hello,
    If the bottom seal is definitely worn then it is quite a simple job.The seal is just pushed into a groove at the bottom of the door,as you pull the old one out be very careful as the edge of the groove is like a knife edge,the new seal will push in gently starting from one end and keep pushing into the groove try not to stretch the seal in length.Another thing to check first is check the bottom spray arm for splits on the edges as this could be directing the water onto the door,if there are splits then the arm will need replacing.

    Hope this helps.

    May 27, 2010 | Dishwashers

    2 Answers

    How do I remove and then replace a new door seal on my hotpoint WD420 washer / dryer


    First switch off electrics , Remove door interlock , leave wires on .remove soap dispenser,remove front panel with controls 3 screws top of machine 3 screws bottom remove front casing you can now see door boot. remove sring note how boot came off refit is oposit to this noting top / bottom of seal ..Hope this some help-

    Oct 03, 2009 | Hotpoint Ariston Aquarius WD420 Front Load...

    1 Answer

    Door lock whirlpool front loader


    remove bad around door seal roll seal back at lock location remove the torx screws holding lock in pull lock out through front and remove wires reinstall in reverse..good luck with retaing band can be fun

    Jun 05, 2008 | Whirlpool Duet GHW9150P Front Load Washer

    Not finding what you are looking for?
    Refrigerators Logo

    Related Topics:

    111 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Refrigerators Experts

    John Tripp
    John Tripp

    Level 3 Expert

    4654 Answers

    yadayada
    yadayada

    Level 3 Expert

    74544 Answers

    Brian Coughlan

    Level 2 Expert

    275 Answers

    Are you a Refrigerator Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...