Question about Sony Grand WEGA KDF-42WE655 42" Rear Projection HDTV

1 Answer

Hi again So, you are saying 3 blinks means the lamp cover my not be in place? It said on a web site that 3 times means the power supply..Strange. Is there a power supply for the lamp all on it's own? or does the power supply for the TV universally power everything?

Posted by on

  • Anonymous Sep 10, 2008

    15 FLASHS ON LAMP LIGHT

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 51 Answers

Yes 3x its lamp cover no doubt. ballast supply will give different error on this unit. this should help hdtv man

Diagnostic Item
Description
Number of times
STANDBY or LAMP LED
lamp flashes
Probable Cause Detected Symptoms
Lamp cover error 3 times - Lamp cover is not fastened securely - No picture/No sound
Fan error 4 times
- Fan1-4 Power is not supplied.(G2 board)
- Fan connector is not seated securely
- Fan caught wires or harnesses
- No picture/No sound
Temp error 4 times
- Internal temperature is too high
- IIC-E line connector is not seated properly
(WE:H3 board, WF/XS:H4 board)
- No picture/No sound
Lamp driver error 5 times - Lamp driver defect - No picture/No sound
Low B error 6 times -No "DD 6V " output (G1 board) - No picture/No sound
Audio error 7 times
- Short-circuit of Audio power supply line
(KD board, G1 board)
- Blowout of a fuse
(F4702,F4703,F4704 on KD board)
- IC failure
(IC4703,IC4708,IC4710 on KD board)
- No picture/No sound
D-OVP error 8 times
- Overvoltage of +3.3V or +2.5V
(A board, B board)
- No picture/No sound
ATSC-OVP error 10 times
-No "DTL MODULE 5V " output
(G1 board, G2 board)
- No picture/No sound
Lamp error LAMP-LED is ON. - Lamp is dead - No picture/No sound

Posted on Jul 01, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

TV wont turn On, standby light blinking 3 times, Help !!!


Hello,

Your power supply board is dead, u know basic electronics' and soldering? Most of the times, the power supply board just have dead leakages gases capacitors.These capacitors always bulges up on it top,or puff up on it top.Replaced these gases leakages capacitors will get your TV power stable,and work again.Or tries websites like Shopjimmy.com,Ebay.com to buy a whole refurbish power supply board for the replacement.


Good luck in solving the problem...

Jun 16, 2011 | Sony Projection Televisions

9 Answers

Sony KF 42WE610 blinking red (non-lamp light) won't turn on


That code represents a power supply board failure. probably a solder break or, circuitry separation.

Feb 13, 2009 | Sony Grand WEGA KF42WE610 42" Rear...

2 Answers

Sony Grand WEGA KDF-60XBR950 60 green orange green red flashing light


3 blinks is a lamp cover error, did you make sure that the lamp cover is screwed in tight? Also check the lamp cover for deformity, there is a problem with your model where the set over heats and melts the lamp cover a little causing it not to make connection with the lamp cover switch. Let me know if you find either of these problems? If not we can troubleshoot a little further.

Tim Nolan

Sep 14, 2008 | Sony Grand WEGA KDF-60XBR950 60" Rear...

1 Answer

Power light is flashing 3 times consecutively. When hitting the power button the fan comes on then shuts back down..then starts flashing the red light again..I've recently bought a new lamp and installed...


Put lamp cover back in its place as 3 times blinking light shows lamp cover has not been fixed.
Lamp cover is first thing that you removed to replace lamp in tv, make sure it is fixed securely in its position.

Aug 13, 2010 | Sony KDF-50E2000 50" HDTV

1 Answer

Changed lamp and TV won't turn on, power light flashes 3 times


Hi,
Red light blinking 3 times shows problem with lamp cover.
Lamp cover is not fixed securely in your tv after lamp replacement. Lamp cover is first thing that was removed to replace lamp, check lamp cover and make sure its back in place properly.
Thanks.

Jul 17, 2010 | Sony Grand WEGA KDF-42WE655 42" Rear...

1 Answer

Powers off red light starts blinking


Hi,do you hear any strange noises? If you hear clicking or like wanting to turn on it could be the board that powers the lamp it's called the ballast.But if you don't hear any strange noises,tv is around 4000 hrs,2-3 yrs it could be time to replace the lamp.The lamp you need is 915B403001.Have a blessed one!

Mar 23, 2010 | Mitsubishi WD-Y657 65" HDTV

1 Answer

KDF 50WE655


3 times blink means Lamp Cover is not placed back that was removed while replacing lamp, make sure lamp cover is fixed securely in its position.
Thanks.

Sep 28, 2009 | Sony Grand WEGA KDF-50WE655 50" Rear...

2 Answers

No picture


I disagree with given info, this tv has no horizontal output transistor because it is dlp tv.
3 red light blink means lamp cover is not placed back properly after lamp replacement/ lamp checking. Make sure lamp cover is fixed back in its place securely and tight.


Jul 16, 2009 | Sony Grand WEGA KF42WE610 42" Rear...

1 Answer

My sony kdf50e2000 power led flashes 3 times then pauses then flashes again...and so on.


Hi,
I hope you recently tried to replaced lamp in TV. 3 times blink shows that Lamp cover is not securely attached.
Please check Lamp cover.

Apr 01, 2009 | Sony KDF-50E2000 50" HDTV

3 Answers

Tv keeps turning off?


cutta, you will most often hear a click on boot then the fans start up and lamp will then fire. The picture will start to show up....at what point does it shut off? and do you hear a click when the tv is turning off? Is it the complete tv shutting down, fans and everything that turns off? Do you see any lights on the the front panel "POWER", "STATUS" or "LAMP", what are they doing? If you see a Power, Status or Lamp light after it shuts off the below are what they mean if there is an issue. POWER - STATUS - LAMP - CONDITION/ISSUE: Off - Yellow - Off - Temp. high/dirty filter/excess room temp Off - Off - Yellow - 4000 hrs. Lamp usage warning Off - Off - Blink Yellow - Lamp Cover open Off - Blink Yellow - Off - Air Filter Cover open Off - Off - Red - Lamp failure (failed to turn On or broken) Off - Blink Red - Off - Fan Has Stopped Off - Red - Off - Circuit failure (short) or DVI cable disconnected If you want to check for the last "Error Code", after you first turn the TV on, by pressing the front panel ?DEVICE? and ?MENU? buttons at the same time and holding them for 5 seconds, it activates the Error Code Mode. The ?Power LED Light? blinks/flashes (1/2 sec delay) and then flashes again denoting a two digit Error Code indicating no problem or an error has occured since the last Initalization. i.e. "Power light" blinks 3 times (1/2 second delay) and then blinks 4 times then 1 sec delay and repeats a few times. This would mean "Error 34 - Lamp abnormality". See below for error codes..... Error Code - Description or issue 12 - No Error detected, check Power Supply 32 - Lamp Cover is open 33 - Air Filter Cover is open 34 - Lamp abnormality 36 - Light Engine (DMD or LAMP Fan stopped) 37 - Exhaust or Lamp Ballast Fan stopped 38 - Lamp temperature high 39 - DMD temperature high 41 - Short is detected 44 - DVI cable between FMT & Engine disconnected. Sorry for the long answer but it was an open ended question.

Jul 11, 2007 | Mitsubishi WD-52525 52" Rear Projection...

Not finding what you are looking for?
Sony Grand WEGA KDF-42WE655 42" Rear Projection HDTV Logo

544 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sony Projection Televisions Experts

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1128 Answers

Ap12
Ap12

Level 2 Expert

103 Answers

Jason Harris
Jason Harris

Level 2 Expert

256 Answers

Are you a Sony Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...