Question about E-Machines eMachines Desktop PC

1 Answer

T3882 keeps rebooting

I need some help my emachines t3882 keeps rebooting to the safe mode screen when i pick run windows normaly it keeps rebooting to the same safe mode screen wht do i do

Posted by on

  • gcabrera0363 Jul 21, 2008

    i did try to install the os but it didnt work

  • Anonymous Dec 28, 2008

    the computer keeps on rebooting after i run windows normally or safe mode, so basically it won't come to main page. what should i do???

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 42 Answers

There could be possible problems with ur smps... dat wil make it reboot frequently ,cos of low power supply to the board... anyway, first try to reinstall the os...

Posted on Jul 17, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cant boot up EMachines T3882 no quick boot and f8 does nothing, what do i do?


If you can't get into the bios, you can't start a repair, when it's booting, continually press F2 to get the bios up, if that does nothing reboot an continualy press Del, this is for the bios menu and set the cd drive as first boot device.

If not continually press F8 on boot up this is safe mode, then when youre in highlight last known good configuration and press Enter.

Give this a try as your pc will not be set to boot from cdrom as default and will just try to boot into windows.

Sep 12, 2012 | E-Machines eMachines Desktop PC

2 Answers

My eMachines T3882 with Windows XP just reboots over and over


Sounds like a sick hard drive. When it starts to reboot, press F8 and choose Windows Diagnostic Test. It will show a hard drive failure if one exists. If it finds a hard drive error, the hard drive is junk and needs replacing. Once replaced, you can run your restore/recovery disk to install Windows back to the condition it was in when you bought it.

Dec 16, 2009 | E-Machines eMachines Desktop PC

1 Answer

Emachine reboot problem


First of all remove ant cd from drive when booting up uinless you are using a bootable windows disk. if the problem still persist when then computer starts booting up keep pressing f8 until you get the choice to go in to safe mode. Once in safe mode choose the option when prompted go to system restore points and restore the computer to a date availabe wich is before the date of the problems.

Aug 19, 2009 | E-Machines eMachines Desktop PC

1 Answer

Wont load passed windows xp screen


Try holding down the "F-8" key when the emachines logo appears, see if you get a prompt for "safe mode". If you can get the system up and running in safe mode, shut it back down from the start menu. That should rewrite the boot sector and may clear the problem.

May 10, 2009 | PC Desktops

1 Answer

Emachine w3107 reboots when windows xp loads


These kinds of issues are most often related to driver conflicts. First thing you need to do is reboot your PC while holding F8, until you receive the menu about booting in to Safe Mode. Try booting in to Safe Mode.

If you can get in to Safe Mode, disable any new devices you have recently installed, reboot again, this time letting it try to boot all the way to Windows.

If it reboots again, go back in to Safe Mode and disable/uninstall something else.

Basically, it is a process of elimination. Safe Mode loads a very minimal set of system drivers, so if you can boot in to Safe Mode but not in to full Windows, the problem is one (or more...) of the drivers that load in Windows but don't load in Safe Mode.

Mar 19, 2009 | E-Machines eMachines Desktop PC

1 Answer

Screen resolution changes after rebooting computer


Restart you computer in safe mode (press F8 when you turn it on) select boot with networking update your antivirus and do a full scan than scan for spyware. This might take care of the "bug" that is doing this to your computer.

Dec 27, 2008 | PC Desktops

1 Answer

Can't bootup my EMachines T3882


if you can't get into the bios, you can't start a repair, when it's booting, continually press F2 to get the bios up, if that does nothing reboot an continualy press Del, this is for the bios menu and set the cd drive as first boot device.

If not continually press F8 on boot up this is safe mode, then when youre in highlight last known good configuration and press Enter.

Give this a try as your pc will not be set to boot from cdrom as default and will just try to boot into windows.

Aug 19, 2008 | E-Machines eMachines Desktop PC

2 Answers

Only getting EMachines/Windows XP Logo when boot up T3882


you have not set the cdrom as first boot device in the bios (press F2 or Del on boot up to get in bios), choose cd as first boot device, save settings and restart the pc with your cd in the drive and then when prompted press enter

Aug 18, 2008 | E-Machines eMachines Desktop PC

1 Answer

Blue Screen Error


Try rebooting your computer on safe mode to fix minor problems. If this dosent help you may need to run your recovery disk or try re-installing your operating system. Chances are your system files are corrupted or may have a problem.

Jun 23, 2008 | E-Machines eMachines Desktop PC

Not finding what you are looking for?
E-Machines eMachines Desktop PC Logo

Related Topics:

260 people viewed this question

Ask a Question

Usually answered in minutes!

Top E-Machines PC Desktops Experts

joecoolvette
joecoolvette

Level 3 Expert

5660 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3051 Answers

Are you an E-Machines PC Desktop Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...