Question about B&W ASW1000 Speaker

1 Answer

How to test your speaker

I have a maddenning problem with my 5.1 home theater system. The deneon 1601 yes its a little old, am goes into auto protect mode occasionally and now its gone into auto protect at all times . It was connected to KEF Cresta 1s, cresta2, kef centre and PSW100 . When i took the amp into deneon in the uk, they found no fault and said it could be a speaker problem. I took the speakers to the KEF dealer and they coudlnt kind anything wrong with the speakers. I am now aiming to change the amp to a denon 3805 but dont want to risk blowing it if the spakers are to blame. |Is there any way to test the spaekers at home before i go and buy a new amp? i an not very techie I have just recently changed to an ONkYO TX-SR 805. I cannot get any sound fron B & W ASW100. I removed the cable from the receiver and touched the middle terminal. I did the same test with a B & W 601 Sub not currently in use. same result no sound while connected or disconnected to the Onkyo.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 151 Answers

Check sub buy pushing cone in gently if you hear or feel a rasping sound the sub is blown,if not check for a fuse where the power cable goes in as this may need replaced.Also make sure you have the sub plugged into the sub pre out and not the six channel input.
PS did switch on the sub in the speaker set up in the menu?
hope this helps.
CABLE GUY.

Posted on Jul 02, 2008

2 Suggested Answers

gadget
  • 14 Answers

SOURCE: how to test your speaker

If the wire is bear ( no port connections ) then you should be able to try the speakers on most stereo systems. If you have not got the right connections on the back of you stereo then ask a friend if you could try it on there?s. But if the wires have got port connections the only way you can test them is if you can unplug your amp and still have the other speakers on. If your going to get a new amp then why not get some new speakers to go with it.

Posted on Aug 24, 2006

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is it intermittently losing channels...front speakers and or rear surround?


How to troubleshoot low sound or no audio from the rear ...

https://us.en.kb.sony.com/.../how-to-troubleshoot-low-sound-or-no-audi...
Aug 15, 2015 - Verify that the rear surround speakers are properly connected to the ...For Dolby® ProLogic surround sound, the center-channel mode must be set to ... the center or rear surround speakers for the Home Theatre (HT) system.

Why Are My Speakers Producing Static? - Electronic House ...

www.electronichouse.com/.../home-audio/why-are-my-speakers-produci...
Here are 3 reasons that speakers produce static and solutions you can try. ... If they are your dedicated front L/R channels speakers in a 5.1 or 7.1 system, you more ...Since you have no problem with your existing rear speakers, if they begin to distort on... Home Theater Subwoofer Puts Boom in This Room · Soundbase vs ...

How to Check if your Speakers are Wired Correctly ' Richard ...

www.richardfarrar.com > Podcasting
Mar 25, 2009 - Attaching speakers to your Hi-Fi system usually only requires a few cables. ..... Is this test applicable for a home theater setup with 5 speakers? ... frontstereo speakers, but to do a similar test on your rear surround speakers would ... Yes, switching polarity on one channel of the amp output to your speakers ...

Pioneer VSX-816 speaker drop out - AVS Forum ' Home Theater ...

www.avsforum.com/.../1068233-pioneer-vsx-816-speaker-drop-out.htm...

Sep 20, 2008 - 30 posts - ‎24 authors
The right front speaker sound drops out intermittently as of about 6 months ago. ...mode and back to Auto Surround would bring the center channel back. ... the push pin that holds several grey wires in place, and pull the wires loose. 9. ..... Is it possible that the cold joints are elsewhere in the system, but that ... Yamaha RX-V663: Intermittent/No Audio in Front ...
4 posts
Jan 23, 2014
Sony Receiver going in to Protect Mode
16 posts
Jan 12, 2012
The Official Sony STR-DH820 Thread
30 posts
Aug 29, 2011
Denon AVR-1910 - No more sound.
30 posts
Feb 15, 2011
More results from www.avsforum.com

Dec 12, 2015 | Audio Players & Recorders

1 Answer

My samsung ht-x30 shuts down after 5 secs and displays protection


Hello
disconnect all the speaker connections, and switch ON the set only, and see whether any protection function energizes or not. If yes, the fault is with the amp itself, and most likely to some damge of components in the output circuit section of the amp. If the amp does not show any protection, when all the speakers are disconnected, make sure that, any one amoung the speakers be the cause of this problem. Connect one after an other and find out which one causes protection circuit to energize. OK.

Dec 28, 2011 | Samsung HT-X20 Home Cinema 600W Theater...

1 Answer

I get a PROTECTION message on my system. What is


the unit goes into auto protection mode whenever there is a shorted pair of speaker wires. check all the connections carefully to make sure no wires are touching any others on the back of the main unit and at each speaker

Nov 03, 2009 | Samsung HT-TX72 Theater System

1 Answer

Sony home theater system started blinking protect


Protect mode will kicking whenever a fault is detected.

Causes that can start protect mode are:

Electrostatic harges on internal circuits.
Leave the unit unplugged for power for one hour or so, this will allow discharge.

Bad speaker wiring.
Check speaker wiring, try unplugging and plugging back, or start after removing one speaker at the time.

Internal fault.
Internal fault is the natural cause for protect mode. If all the above did not work, then the problem is a blown component or an internal fault. In this case the unit must be taken apart , tested and repaired by an experienced person.
If the unit is less than one year old, or if you want to get service, call Sony at the phone number listed on the product documentation.

Regards.




Mar 23, 2009 | Sony DAV-DX250 System

1 Answer

"protect" on the screen


Protect mode will kicking whenever a fault is detected.

Causes that can start protect mode are:

Electrostatic harges on internal circuits.
Leave the unit unplugged for power for one hour or so, this will allow discharge.

Bad speaker wiring.
Check speaker wiring, try unplugging and plugging back, or start after removing one speaker at the time.

Internal fault.
Internal fault is the natural cause for protect mode. If all the above did not work, then the problem is a blown component or an internal fault. In this case the unit must be taken apart , tested and repaired by an experienced person.
If the unit is less than one year old, or if you want to get service, call Sony at the phone number listed on the product documentation.

Regards.

Jan 18, 2009 | Samsung 650W 5.1-Channel Home Theater...

1 Answer

Sony Home Theater 5 DVD changer, was dropped in transit


if you know how to open it, remove the top cover( a couple of screws on the rear) and remove two connectors, one being a ribbon cable and the other a multiple wire connector. If it still does the protect, then it is not from the dvd mechanism but a fault on the board.

Jan 17, 2009 | Audio Players & Recorders

1 Answer

Home theater system hx-tx72


Protect mode will kick in whenever a fault is detected.

You get the unit not powering up, and sometimes you hear a clicking noise, that is the protection switch that keeps shutting down the unit.

Causes that can start protect mode are:

Electrostatic harges on internal circuits.
Leave the unit unplugged for power for one hour or so, this will allow discharge.

Bad speaker wiring.
Check speaker wiring, try unplugging and plugging back, or start after removing one speaker at the time.

Internal fault.
Internal fault is the natural cause for protect mode. If all the above did not work, then the problem is a blown component or an internal fault. In this case the unit must be taken apart , tested and repaired by an experienced person.
If the unit is less than one year old, or if you want to get service, call Sony at the phone number listed on the product documentation.

Regards.

May 30, 2008 | Samsung HT-TXQ120 Home Theater System...

4 Answers

How to test your speaker


Units going into auto protect are usally due to open or dead short conditions to keep the system protected from blowing the final amps. based on what you suggested I woould test or change out the cables 1st.

Aug 24, 2006 | KEF Audio Cresta 2 Speaker

Not finding what you are looking for?
B&W ASW1000 Speaker Logo

554 people viewed this question

Ask a Question

Usually answered in minutes!

Top B&W Audio Players & Recorders Experts

sonic boom...
sonic boom...

Level 3 Expert

1557 Answers

Iron
Iron

Level 3 Expert

3018 Answers

Tom Chichester

Level 3 Expert

29754 Answers

Are you a B&W Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...