Question about Kenwood Car Audio & Video

1 Answer


Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has achieved Level 3.

  • Master
  • 726 Answers

If the radio needs a code it will be in the car handbook or if that is unavailable the only other option is to ring the manufactorier to obtain the 4 or 5 digit code be sure to write it down incase this problem occurs again

Posted on Jul 02, 2008

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to remove the rear subwoofer in a 2001 cadilliac deville

I assume you are talking about the rear deck speakers. In these model vehicles they don't make it easy. Some have access from the truck. There are a couple of plastic boxes under where the speakers are. These are the baffles. If this is the case, you can usually remove them from the trunk. There will be a few nuts holding them on. Other cases require you to remove the back deck to access them. At any rate, if you are not mechanically inclined, I recommend taking it to a local stereo shop and having it done.

Aug 14, 2011 | Car Audio & Video

1 Answer

Hi. I am having a bit of trouble after having to change a blown fuse and now I don't have the code for my stereo.

The radio SERIAL NUMBER is required for a code
First remove the radio from the dashboard.
Then post the radio make+model plus all the letters+numbers on any labels,barcodes or stamped in the metal casing.
This information can then be used to see if a code can be calculated

Jun 12, 2011 | Car Audio & Video

1 Answer

Battery was disconnected and now the radio says Code Wait. I have Radio Code, but don't know how to enter it. The manual does not address the stereo system. The system is in a 1999 BMW 323IC. Where...

Leave the radio SWITCHED ON...UNDISTURBED for as long as it takes to automatically reset itself
This may take an hour or more
Make sure you have the correct code

Jun 10, 2011 | Car Audio & Video

2 Answers

Im looking for a procedure to remove the safe mode on a smart 450 stereo car. I have the code number, but I really don't know how to introduce it.

It is showing SAFE because wrong codes have been entered previously

Leave the radio SWITCHED ON...UNDISTURBED for as long as it takes to automatically reset itself

It may take an hour or more

May 09, 2011 | Car Audio & Video

2 Answers

Does the profile mp9300 car stereo have an aux input? If so, where?

Yes, the mp9300 has axillary in. It has a pair of traditional RCA red/whites coming out of the back of the stereo.

I am assuming you are wanting to plug an iPod or Zune type device directly into it. To do this you would need to pull out the stereo to access the RCA inputs and add an RCA to 3.5mm adapter like this one.These are commonly found at radio shack, best buy, walmart, or any electronics store for typically under $5.

After you install the adapter you can simply route it behind the stereo and out the back underneath a panel in the car so you can access it.

I have included a diagram of the wiring to help you out should you chose to decide to do this yourself.

Good luck!!

May 06, 2011 | Profile Car Audio & Video

1 Answer

Battery discontected. Stero now does not operate. Need stereo code. Hyundai Sante Fe 2005 VIN: KMHSC81DR5U900169 Thanks

I don't know how much luck you will have, but open the glove compartment and look all around for a little sticker, possibly white. It should have code. A lot of vehicles that needed codes were factory installed with a code stuck inside the glove compartment. If there is no code in sight, I would suggest calling your local Hyundai dealer for possible location of the code or bringing it in for a reset. Hope this helps!!

Apr 15, 2011 | Car Audio & Video

1 Answer

I can,t get the code for my stereo anywhere no matter what i pay!! I have a volvo cr902 serial number is v01140 w7101047 30850648 can anyone help?

This MITSUBISHI radio code will not be available for free (or cheap) from anywhere on the Internet as access is required to the VOLVO database which is not commercially available

Only available from your Main VOLVO Dealer or a Radio Decoding Service


Jan 31, 2011 | Car Audio & Video

1 Answer

Code for locked stereo


May 10, 2009 | Car Audio & Video

1 Answer

Code for blue tooth access to Pioneer DEH-P7900BT car stereo.

try 0000 that is the default code for my bluetooth device for my phone , "Hey you never know "

Sep 14, 2008 | Pioneer Car Audio & Video

Not finding what you are looking for?
Car Audio & Video Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenwood Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

4724 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Pablo Gonzalez

Level 3 Expert

733 Answers

Are you a Kenwood Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides