Question about Maytag Washing Machines

1 Answer

Maytag model LAT9605AAE serial # 13662937QD washer gets out of balance constantly on every spin cycle

Posted by on

  • Anonymous Mar 23, 2014

    80% of the timer control section does not work. Do I have to replace or is there an adjustment that I can do

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 481 Answers

Make sure all of the legs are adjusted correctly. maytag washers also have to be on a very stable floor. if the floor is not stable or if the legs are not adjusted properly then the machine will shake all over as if they are out of balance.

Posted on Jul 01, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Constant out of balance on washer


Check the inter tub ring you should hear water when you spin it by hand
if you dont hear water replace the spin tub balnce ring it must be cracked or has a hole in it and leaked out the fluid this is a counter balancer when it gows into the spin cycle
h Tech AL Wojo

Apr 01, 2013 | Maytag Bravos MTW6600T Top Load Washer

1 Answer

Maytag atlantis washer doesnt spin on spin cycle, also found plastic shavings in clothes, appear to be coming from the top outer edge of the tub, a white plastic trim piece. wash cycle seems to work fine...


There can be several causes, the drum off balance would cause the shavings during spin cycle , balance could be one of the the balancing mechanism failed and not running could be the balance sensor shutting down the spin cycle. You should start by checking the balance shocks .

May 14, 2011 | Maytag Atlantis MAV9750A Top Load Washer

1 Answer

Maytag Performa Washer PAV1000AWW. Shakes when spinning out


My washer doesnt drain in the rinse cycle?? dont kno what to do

Feb 15, 2010 | Maytag Performa PAV2200

1 Answer

The wash time continues to increase on every cycle. I have a Maytag Neptune TL Washer.


Thank you my machine model number. The reason I ask is so many folks post non FAV6800A/FAV9800A issues in this forum. This forum doesn’t ask for machine model number and serial number. Here we go.

Does your machine seem to take longer than normal to fill with water?

Does the machine increase the time during the Spin Cycle of the Wash Cycle?

Are there any error codes to the LED display such as dC or uC?

Do you want to work toward a DIY fix? If not maybe we can get a solid feel for the issue that will help you in the decision process to bring in a repair company or replace.

So I can better understand the issue can you start a Quick Wash cycle with Soil and Spin settings set to lowest setting and if you could place a couple of bath towels in the wash basket for a load.

I want to see if the machine will go thru the Wash, Rinse and Spin cycle within the 27 to 29 min time of a Quick Wash cycle. I want to see if the machine is increasing Washer Cycle time in the Spin Cycle of the Wash Cycle.

You should enter the Rinse Cycle at the 20 min mark on the LED display.

You should enter the Spin Cycle at the 10 min mark on the LED display.

Watch the cycle and see if you have similar times as I do. Let me know if the washer has any off balance issues as it enters into the Spin Cycle…..Rich

Jan 17, 2010 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

OUt of balance during rinse and spin cycles


I have the same problem. During the spin cycle, the washer spins all over the room.....very loudly.

Dec 26, 2009 | Maytag Washing Machines

2 Answers

Maytag washing machine gets out of balance


Maytag uses an auto balancing mechanism, based on the rear legs. These legs should move freely. Lay the machine on its side, and try to move the rear legs. If they won't move and appear rusty, then spray penetrating oil on both legs and move them until they move freely.

Sep 27, 2009 | Washing Machines

3 Answers

Washer tub goes off balance every time and washer walks!


there may be a possibility here of the centre hub being worn or the liner tub bearing being worn due to the age of the machine.. here is a list and diagrams of the parts you may need and can get from here:-
http://www.easyapplianceparts.com/MultiModels.aspx?ModelNum=mat13mn&searchTerm=img_CW17-6&RefineSearch=0&imgMfg=Maytag

try to check for slackness when the tub is empty causing a rocking/slapping motion whilst empty. if the tub is used regularly and to its maximum capacity then the likeliehood is these bearings/hubs may need to be replaced.. the "walking" across the floor will be accented by the amount of items plus water in the tub. and if the tub is off balance,then this will be more highlighted when also full of water and items... if you feel this is over the top,then try to lighten the load that is in the tub at any given time. this will determine weather the bearing has indeed worn .the lighter the load,the less "walking the machine should do in cycle.. the only time walking would be unchanged is during the spin cycle,when the speed is of a constant one and it will vibrate at the same rate. placing it on a rubber mat is not a solution but just something that will make you hopefully think it is solved
and you may as well just bolt the machine to the floor and hope for the best

Mar 31, 2008 | Maytag MAT13MN Top Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

521 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Al Clark

Level 2 Expert

290 Answers

Todd Marr
Todd Marr

Level 2 Expert

77 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...