Question about Frigidaire Dishwashers

1 Answer

Dish washer heating coil less then 2yrs old is developing a crust on it. any concern

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 161 Answers

Use one of the dishwasher cleaning products. Run without dishes. Can also use Lime Away.

Posted on Jul 01, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dishwasher not cleaning dishes


If it is a cheaper brand/model of dishwasher, you may have to rinse the dishes, especially if they have been sitting for a while. While there are dishwasher who are powerful enough to clean even crust off the dishes, most need to have the dishes rinsed off even just with cold water right after use....If you do not use alot of dishes per day and let the washer build up dishes after a few days then I would recommend a warm/hot water rinse even with a dish sponge and some soap. While some may think that this defeats the purpose of using a dishwasher, remember that a dishwasher is more sanitary that using a dish rag or sponge that had the opportunity to build up bacteria and other gunk over a period of time ;-)

Aug 28, 2013 | Kenmore Dishwashers

1 Answer

My dishes still come out wet..how do i set the washer to dry the dishes


there should be a setting or a button to turn the heat dry on and off, if it is on and dishes are not drying then the next time you do a load of dishes pay attention to the cycles, after the rinse cycle is complete the heat should come on. if not you could have either a bad heating coil or a bad relay.

Aug 20, 2009 | Kenmore Dishwashers

2 Answers

My brand new dishwasher leaves white film


The new washer is drying the dishes faster that the old one,Try setting it to no heat dry and see if that helps,if so you will need a water softener or filter for the water line to the washer.

Jul 29, 2009 | Dishwashers

1 Answer

GE Dishwasher fills with water but does not "spray water" on dish


Here are a few things that might help you out, first is you could have a bad heating element in your dish washer, when it fills with water it has to reach a certain temperature before continuing to the next cycle, next thing is you could have a bad thermostat, or your timer is defective.

Mar 16, 2009 | Kenmore 16522 Built-in Dishwasher

1 Answer

Water will not drain out of my dish washer.


unless you actually have a blockage in the outlet then chances are either the pump has died or less likely the circuit board that holds the programme has developed a fault... the replacement pump is the cheaper the board may cost quite a bit (compared to simply replacing the whole machine) lets hope it is simply a blockage in the pipe

Oct 20, 2008 | Dishwashers

1 Answer

Chalky dishes in dishwasher


that normally means that the lower arm is clogged or filter indeed clogged.
Make and model number would be helpful

May 07, 2008 | Dishwashers

1 Answer

D3 error code


try running it in service diagnostic and let it finish will check its self and clear error codes in less than 6 seconds push heated dry-normal-heated dry-normal and advise me

Jan 23, 2008 | Whirlpool GU2400XTP Built-in Dishwasher

1 Answer

MAYTAG DISH WASHER MODEL 41-ESP4-DISH


I suggest calling Maytag and have a tech come out to look at it. Appliances come with a one year parts and labor warranty.Use it before your one year is up.

Nov 17, 2007 | Maytag 24 in. MDB3700 Built-in Dishwasher

Not finding what you are looking for?

Open Questions:

0 Answers

what part? Frigidaire Dishwasher FDB1050REC. Dishwasher goes through cycle but then light gets stuck on "CLEAN". I turn off and on the circuit breaker. Three lights flash on the control pad. I press start/cancel and the light off and I can then start another cleaning cycle again like normal. Of course I can't do this every time I want to use the dishwasher. But I have noticed that if I press cancel during the "DRY" phase (DRY light is on), before it gets to "CLEAN". I can use the machine again no problem. In essence, I have to catch it while the "DRY" light is on, before the clean light goes on. I have run into this problem before and here is a detailed step by step description: The first time this happened, I was told that it was a control board problem so bought a new one, installed it but it did not work. Someone the suggested that it was a door latch problem. I then replace the door latch and it worked!! A year later the same problem occurred so I replaced it with a new one again,thinking that if it solved the problem the first time then it should again. Unfortunately it did not work. So I tried putting back the original control board and it worked again. So this time it seemed to be the control board. Worked for another few months until I smelled something burning. After that the machine did not work and it is at the stage that I described above. Are you able to help diagnose the problem? Could it be the wires were over heated? If so that would be of great help. Hopefully my description is detailed enough. Many thanks, Edward

Oct 03, 2016 | Frigidaire Dishwashers

Dishwashers Logo

Related Topics:

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Frigidaire Dishwashers Experts

Electrolux
Electrolux

Level 3 Expert

4342 Answers

Carmen Mikulic

Level 2 Expert

409 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you a Frigidaire Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...