- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
you don't need the software, just connect the router to your pc via an ethernet cable, go to your web browser (internet explorer, firefox, etc) and in the address bar, type 192.168.2.1
once there, you should be able to configure your router for your internet connection
all you need to do is:
1. disconnect your wireless antenna on your PC
2. plug your pc into the router with an ethernet cable.
3. open your browser and type in 192.168.0.1
4. the password is admin and there shouldnt be a username but if there is the default is also admin
5. configure your settings
*before you change your settings practice on this emulator in order to familiarize yourself
hope this helped plz rate thx
If the power supply isn't working by that you mean the light on the back of the power supply when the power cord is plugged in does not luminate green ? then yes it is bad. There is also a paperclip trick you could try depending on how tech savy you are. Google paperclip power supply self test. Bottom line if the power supply is bad its a relatively simple fix. Go to your local pc shop pick one up for 20-40 bucks and crack the side of the case and take note of the wires when your unplugging them from the motherboard, cd, hard drive and floppy and replace with the new one you bought. hope that helps. Thanks.
may i request any one to kindly share a basic networki ng ideas in office...what else configuration,devices and how network should look like..etc:-....m not sure how my question really suits, but please help me by answering..
The CallPilot takes between 4 and 15 minutes (depending on software level) to boot up. After that, the lights should come on for each port connected to the telephone system. If not:
1. Check the wiring between the phone system and the CallPilot;
2. Make sure the wiring between the phone & voicemail systems is less than 50 ft. (15 meters);
3. Remove & reinsert he feature cartridge.
If still not working - the unit needs repair.
This is likely because out of the box, the firmware for this unit doesn't support WPA2 and even certain variants of WPA. I recommend: configure router for WEP or even open (i.e. unencrypted) connection, connect unit, go to setup/update firmware and let it update from network, power cycle, reconfigure your router for WPA or WPA2 security, attempt to reconnect unit to wifi. The updated firmware supports more formats and may allow your new router's config to work. You can also try doing the firmware update over the wired LAN port. Hope this helps.
The color is not so important as the cable follow the same standard on both ends.
It has been my misfortune to find non-standard wiring in a facility, so long as they keep the relationship of the pins the same it will work, if the installer did not then you cannot trust any of the work and MUST either redo it all or have it all tested and certified by a cometent network cable installer.
568-B Wiring Pair Wires RJ-45 pins 1-White/Blue White/Blue 5 Blue/White 4 2-Wht./Orange White/Orange 1 Orange White 2 3-White/Green White/Green 3 Green/White 6 4-White/Brown White/Brown 7 Brown/White 8 568-A Wiring 1-White/Blue White/Blue 5 Blue/White 4 2-White/Green White/Green 1 Green/White 2 3-White/Orange White/Orange 3 Orange/White 6 4-White/Brown White/Brown 7 Brown/White 8
RJ-45 Pins are with the spring tab down and read left to right. Do you have an RJ-45 Crimping tool?
I know this is an old thread, but for the sake of helping someone else in the future, I just got off the phone with the Phillips Help Desk and this is the way they told me to wire it up the RJ-11 & RJ-45 combo jack I bought (PH60037):
Jack colors - CAT 5e
Blue - white/orange
Orange - Orange
Black - white/green
Red - Blue
Green - white/blue
Yellow - Green
Brown - white/brown
White - brown
White - white/green
Black - white/orange
Red - blue
Green - blue/white
Yellow - orange
Blue - green
He said it was the standard configuration used by the phone companies for some time.
Phillips Help Desk # for phones/PCs (800-233-8412)
Hope that helps someone else down the road.
Had similiar problems with my 2001. Check the entire length of the headlamp wiring harness under the hood behind the grill. They are prone to corrosion from road debris etc. Peel off the tape and follow thw wires. I'll bet there will be a broken one. Pay particular attention to the pink one. Just clean up the broken one and fix it with a **** connector and you should be good to go. Hope this helps.