Question about Audio Players & Recorders

Open Question

Panasonic SA AK 67 Sterio system need spare

I need a new mechanisam of sterio system

Posted by on

5 Suggested Answers

  • 39 Answers

SOURCE: F61 problem

DIsconnect sound Amplifier ic (RSN).After removal of the ic if the unit works o.k offcourse without sound than replace ic.If still f61 than sound ic is o.k and check voltege regulators in power supply.You can check dc detect line if it gets activated.
F61 is mainly two resons 1st sound ic or power supply problem in power bord which send signal to system control to shut down the power in order not to damege more.

Posted on Dec 14, 2007

  • 4 Answers

SOURCE: F61 error in my SA-AK25 Panasonic Audio System

CHANGE STK --------IC

Posted on Mar 27, 2008

tech48
  • 624 Answers

SOURCE: panasonic sa -ak 27

This is a common error for these Panasonic units. I work at an authorized Panasonic service center and have repaired many of these.

This error is caused by either 1 of these 2 problems, both of which will require service for replacement of parts.

1. The amplifier IC is bad and needs to be replaced.

2. There are a couple of smaller components in the amp circuit that need to be replaced. One is a zener diode and the other is a resistor.

The F61 error is caused by a bad amp circuit or power supply circuit. In most cases it is the amp circuit. More often than not, it is the zener diode and resistor that are bad. This would be preferable since the amplifier IC is very expensive and a total repair cost would be close to $200. The zener diode and resistor repair would be closer to about $100 depending on the rates of the service center.

I know this may not be the answer you were hoping to get, but it is the problem you have.

If you found this information helpful in making a decision on what to do with your stereo a FixYa! rating would be appropriate and very much appreciated, after all, it is the only reward we get for offering free help to people like yourself.

If I can be of any further help just reply to the post and I will get back to you as soon as I am able.

Good luck with your stereo, I hope you found this information to be helpful.

Dave

Posted on Sep 05, 2008

  • 6 Answers

SOURCE: program guide for the car sterio features

Go Here

http://caraudio.manualsonline.com/manuals/mfg/alpine_electronics/cde-9852.html?s=fpw

Posted on Feb 20, 2009

  • 1348 Answers

SOURCE: MOVED HOUSE LOST THREAD TYPE AERIAL FOR MY

put a 3 foot piece of wire on it.does the same thing.any parts house will have an antenna ,and for sure an authorized panasonic repair depot...they are listed in the back of the warranty book for the radio

Posted on Jul 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My LN40C530F1FXZA give a massage that the USB 1/2 power overload, new device not found. also none of the HDMI are working. All other components work.


Just do a reset to this set, and then check. There are two methods to reset TVs. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight is better. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; check the site linked here. Pull up older posts. http://electronicshelponline.blogspot.com/
Service mode entry, adjust and exit procedure to many popular brand TVs are given. Never forget to exit the service mode, after all adjustments have been done.

Jan 12, 2017 | Samsung LN40C530F1FXZA LN40C530 40 LCD TV...

1 Answer

Want to use my current speakers with a new surround sound system. Current system is 5.1 channels, rated at 100w per channel @ 8. Ohms. New System is rated 145watts, 5.2 channels at 6 Ohms. Will b ok?


Hi Ronald.
8 Ohm speakers will work just fine as replacements for the
6 ohm speakers. When fitting speakers you need to consider
The power handling capability. The impedance and the frequencies
involved. Power handling is expressed in wattage ie 100W.
Unfortunately this can be expressed in rms, max or peak music. The rms value (root mean square) is the only really relevant figure as this is the continuose handling power at 1 KHz. The impedance
is the resistance that the amp sees but is not a dc resistance and
varies with frequency. The lower the impedance the more power
will be drawn from the amp. In the event of a short circuit across
the speaker the amp will try to deliver infinite power into an infinitly
small load in an infinitesimal amount of time and will self destruct.
Using an 8 Ohm speaker draws less power than a 6 Ohm speaker.
Connecting speakers in parallel; results in the impedance beingreduced. For example two 8 Ohm speakers in parallel will result
in a 4 Ohm impedance load but in series will be 16 Ohms.
Incidentally the the .1 (5.1) is the sub woofer which only has
to handle the bass frequencies, a small percentage of the
amplifiers overall frequency response..
Connect your speakers and then power up the amp last
after double checking there are no shorts on the speaker
cables.
All the very best from Vintie.





Jan 07, 2017 | Audio Players & Recorders

1 Answer

Im still waiting to see the stav 3300 manual that i asked to see before can it be produced or not


Try these they are fairly near. http://support.radioshack.com/support_audio/3151.htm

http://support.radioshack.com/support_audio/26922.htm

Otherwise you an contact us at ELECTREPAIRUSA@ELECTREPAIRUSA we repair/renovate and supply spares for all electronic and electrical equipment.

Jan 07, 2017 | The Audio Players & Recorders

1 Answer

Can't get my Kenwood VR715 receiver to go into the Select a speaker system to see if speakers are turned on. Followed manual instructions and can't get in. Any Suggestions.


Try resetting the unit by unplugging the unit from the wall, then plugging it in again WHILST holding the power on/standby button in. This should reset the system. If not:
ELECTREPAIRUSA@ELECTREPAIRUSA or you can contact us at that address as we repair/renovate all items electronic and electrical old and new.

Jan 06, 2017 | Kenwood Audio Players & Recorders

1 Answer

My Bose 321 switches it self off after 5mins . How do I stop this.


Occasionally the system may have the sleep mode activated , we have come across this before. Reset the system completely.
Any issues.
ELECTREPAIRUSA@ELECTREPAIRUSA or you can contact us at that address as we repair/renovate all items electronic and electrical old and new.

Jan 06, 2017 | Bose Audio Players & Recorders

1 Answer

I have a monsoon mh505 pc speaker system. i lost the power adapter.i need a manfacture phone number or the model number of power adapter.


We can provide one.
ELECTREPAIRUSA@ELECTREPAIRUSA or you can contact us at that address as we repair/renovate all items electronic and electrical old and new.

Mar 14, 2016 | Audio Players & Recorders

1 Answer

The amp section of the circuit bored of my Boston hps 10se is burnt. I need a new circuit bored with amp


We can either repair the board or supply a new one.
ELECTREPAIRUSA@ELECTREPAIRUSA or you can contact us at that address as we repair/renovate all items electronic and electrical old and new.

Mar 05, 2016 | Audio Players & Recorders

1 Answer

MY PANASONIC 5CD STEREO SKIPS WHILE PLAYING CD'S I HAVE USED A HEAD CLEANER AND IT STILL DIDN'T WORK.I HATE TO DISCARD IT.


The laser pick-up unit fault [weak]. You have to replace it with a new one of similar number. Contact any service technician. To replace this part, you have to take out the whole mechanism from the system; and this is a skilled work.
If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. Electro help

Dec 26, 2014 | Audio Players & Recorders

1 Answer

My Jensen MP3 player says ''File System E'' when turned on...


Jensen Mp3 player has qr code on screen, what do I do?

Sep 19, 2009 | Jensen Audio Players & Recorders

Not finding what you are looking for?
Audio Players & Recorders Logo

Related Topics:

121 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audio Players & Recorders Experts

kakima

Level 3 Expert

101609 Answers

 Grubhead
Grubhead

Level 3 Expert

4767 Answers

The Knight
The Knight

Level 3 Expert

71705 Answers

Are you an Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...