Question about DCS BGA48-BQAR (NG) All-in-One Grill / Smoker

Open Question

Replacement parts for DCS 48A BQRS

I am in need of several parts for my DCS 48A-BQAR grill including 3 burners and other parts but I need a schematic of all the parts to the grill so I can tell you what all I need. Could you e-mail a parts list showing a exploded isometric drawing showing each part and its placement of all parts on the grill. Please call me at my office at: 812-683-4376 or my cell phone early mornings or evenings at 812-639-7770. My e-mail address is:
Bill Disinger

Posted by on

1 Suggested Answer

  • 60 Answers

SOURCE: DCS BGB30 BQAR doesn't appear to be getting an natural gas flow

its most likely the ng regulator has gone bad you can get one from most grill stores if you dont know of any call bbq galore 214 696 0030

Posted on Aug 20, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Knob too hard to turn on and off burners

This would need greasing the controls dry out and you get brass on brass take the control knob off there are two screws you can remove and take the plug out and grease it with black control grease . then replace this should then work .

Aug 31, 2011 | DCS BGA36-BQAR (LP) All-in-One Grill /...

2 Answers

Infrared rotisserie burner mounted on back will not stay lit.

I have the same problem - What I determined is first the gas safety valve button would not push in. I researched the problem and found that if you ever overheat your grill by "cleaning it" by placing foil over the grill, then the intense heat likely overheated the valve. ( in my case) which I replaced. After replacing the valve, my rotisserie would not stay on. I found that the thermocouple was defective. the TC is a piece of copper that attaches to the back of the safety valve and the other end has a probe that is up at the rotisserie burner. When you light the rotisserie, and press in the valve button, it should stay lite after about 10 seconds.
When the probe heats up, it sends and electrical signal to the electro magnet which operates and keeps the valve open. I bought my thermocouple from PEX supply for $9.50. DCS wants $56.00 for the same part which is manufactured by Robertshaw. Part number you want is 1980-072 thermocouple .

Dec 07, 2010 | DCS BGA48-BQAR (NG) All-in-One Grill /...

1 Answer

How do I remove the front panel to replace the sparker

On some grills, the valves are also attached with screws to the front panel, these screw are removed and the front panel comes off. If this is not the case, you may have to unhook the gas line from the manifold.

Jul 05, 2010 | DCS BGA36-BQAR (LP) All-in-One Grill /...

2 Answers

Infrared burner goes out

if there is a thermocouple on the burner this could be out of postion or brunt out

May 17, 2010 | DCS BGB36BQARN (NG) Stainless All-in-One...

1 Answer

We inherited a Gas Grill DCS. Need a manual.

You may find one on line or at DCS site

Mar 14, 2010 | DCS BGB30-BQAR Gas Grill

1 Answer

I need 3 burners for Grand Gourmet Gas Grill Model No. GBC621A-M

Try this link:

It should bring you right to your specific grill and list replacement parts including burners.


Sep 08, 2009 | Brinkmann 810-2300-B Grill

1 Answer

DCS BGB30 BQAR doesn't appear to be getting an natural gas flow

its most likely the ng regulator has gone bad you can get one from most grill stores if you dont know of any call bbq galore 214 696 0030

Jul 03, 2009 | DCS BGA27-BQ (NG) Grill

1 Answer

Replacement of gas burners

Hello, The model number that you gave is relatively simple to change the burners.
  1. Remove the 3 cooking grids
  2. Remove the 3 vaporizer tents
  3. Between each burner is a "pal nut" that just pushes on and will likely be destroyed when you remove it. They run a couple bucks each at Sears, part # 7000132
  4. This will release the carry over tube holding the burners down and the burners can be lifted out.
  5. Ensure that you clean out the carry over tube when you reassemble. This carries the flame from the first burner across to each of the rest of the burners when lighting them.
  6. Reassemble in the reverse order ensuring that you put the burner tubes over the burner valve tubes when reassembling.
You can find a parts listing with the parts numbers at:

If this was helpful, please vote yes. Thank You!!

May 29, 2009 | Char-Broil Advantage 463453306

Not finding what you are looking for?
DCS BGA48-BQAR (NG) All-in-One Grill / Smoker Logo

Related Topics:

100 people viewed this question

Ask a Question

Usually answered in minutes!

Top DCS Grilling Experts


Level 3 Expert

2035 Answers

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

Justin Fitzgerald
Justin Fitzgerald

Level 3 Expert

543 Answers

Are you a DCS Grilling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides