Question about Nintendo Wii Console

1 Answer

Wii controller the controller stopped working when i press the controller it flashes but it wont do anything not respond with console only had it 5 days

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 34 Answers

You probably have to sinc it. If you don't know how to you open the tab that is on the front of the wii and open the back part of the wii controller where the batteries go and you will find a sinc button wich when you press will autumatically record the ip adress of your controller for future use. If this is not what it might be try changing the batteries on the controller. If its neither then you might have to return it to see if you can get one that works. Good Luck!

Posted on Jun 30, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

4 Answers

My remotes were synced to another wii how do I re-sync them?


Step by step instructions on how to sync the Wii Remote or Wii Remote Plus to the Wii console using Standard Mode.

Note:

Only a Wii Remote in Standard Mode can turn the Wii console power ON or OFF.

What to Do:

  1. Press the Power button on the Wii console to turn it on.
  2. Open the SD Card Slot cover on the front of the Wii console. If you are using a Wii mini, the sync button is located left hand side next to the battery compartment. The sync button is a darker shade of red than the console.
  3. Remove the battery cover on the back of the Wii Remote to be synced.
    • Some models of the Wii Remote include a hole in the battery cover and a tool on the wrist strap to push the SYNC Button with. With this model, the battery cover does not need to be removed to access the SYNC button.
  4. Press and release the SYNC button just below the batteries on the Wii Remote; the Player LED on the front of the Wii Remote will blink. While the lights are still blinking, quickly press and release the red SYNC button on the Wii console.
    wiiremotesynchstandard.gif
  5. When the Player LED blinking stops and stays lit, the syncing is complete. The LED that is illuminated indicates the player number (1 through 4).
  6. This sync procedure must be followed for each additional Wii Remote added to the system.

May 19, 2014 | Nintendo Wii Console

1 Answer

If the wii remotes aren't working, responding, or charging, can the remotes be reset or do I need new batteries?


First you will meed 2 try new batteries then you will need to press the 'Red' button
located on the Wii console to 'Re-tune' in the Controllers

How to Sync the Wii Remote Standard Mode Wii and Wii mini Nintendo...

May 11, 2014 | Video Game Consoles

1 Answer

My wii remote wont I guess connect it just keep flashing the lights at the bottom anytime I hit anything on the wii remote or try to sync it


Hold both Sync buttons for a period of 5 seconds, then let go. If this does not work, replug everything on your wii and try again. Make sure your Wii is on when syncing.

May 18, 2011 | Nintendo Wii Console

1 Answer

My wii controls have stopped working with chargers and batteries but still flash as if they are going to work then they dont


they just arent registered with the wii. first open the battery door on the wiimote (control) and press the little red button. then open the SD card slot on the wii and press the red button there and the wiimote will connect

Apr 26, 2010 | Nintendo Wii Console

1 Answer

LIGHTS ON CONTROLLER FLASHES BUT WONT RESPOND


you have to reconnect it. Click the home button on your remote click connection settings, and hit reconnect. Then press 1 and 2.

Mar 10, 2010 | Nintendo Wii Console

1 Answer

Controllers wont sync


If you have pressed the sync button on wii, then on the wii-mote, and it still didn't sync, try unplugging the Wii console for few minutes and try the process again.
There is another syncing mode, but you have to have at least one wii-mote connected to the wii. You press the home button and the click on the wii-mote on the screen. There will be a reconnect button. Press that and then press both the 1 and 2 buttons on the wii-mote[s] you want to connect. This is the ONE TIME ONLY connect mode, used when playin on a friends Wii. Once the Wii is powered off, the wii-mote wont be connected any longer and will still be the default wii-mote for your wii system [not on your friends]. Hope this helps.

May 10, 2009 | Nintendo Wii Console

4 Answers

Cant get pass the "press A button" screen


Turn off for a moment, try again, reconnect your controller.

Since its brand new, you can get it replaced if that doesn't work, dont waste your energy on it, just get another one, free replacement / warraty. Im sure.

Sep 05, 2008 | Nintendo Wii Console

1 Answer

Wii remote


open the wii remote battery cover
press the little red sync button once, at the same time as pressing the little sync button under the sd card flap(on the wii) once.
just one tap each and it shud work.
dont keep the buttons pressed or it wont work.
also some people sed to me you can keep '1' pressed

Jun 13, 2008 | Nintendo Wii Console

7 Answers

Wii controller not doing anything


I had this same problem. I read somewhere to unplug the Wii for a minute so that when you turn it back on it will have to reload the bluetooth data from the firmware. Worked immediately for me. Hope this helps.

Jan 21, 2008 | Nintendo Wii Console

Not finding what you are looking for?
Nintendo Wii Console Logo

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nintendo Video Game Consoles Experts

Troy Gorman
Troy Gorman

Level 3 Expert

508 Answers

phil

Level 2 Expert

567 Answers

Raj Patel

Level 3 Expert

845 Answers

Are you a Nintendo Video Game Console Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...