Question about Dishwashers

1 Answer

Hotpoint aquarius DWF33 is it an N a P or an S?

In order to buy spares I need to identify if the machine is a DWF33N a
DWF33P or a DWF33S. I can not find this on the machine. The serial number is-
5600041012/03/56/10:11 can you help identify the type of machine it is?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that has over 10 points.


    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

The part number is etched on the top side of the door, where the release mechanism is housed.

Posted on Mar 27, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Tablet drawer

be sure to check the drawer that it is clean and not sticking. u can order the drawer from and replace it if needed

Apr 06, 2014 | Hotpoint 24 in. DWF33 Built-in Dishwasher

1 Answer

Hotpoint aquarius dishwasher tablet dispenser not working

Clean it by running a cycle with hot water and 2 cups white vinegar, I suspect you have mineral deposits built up and causing it to stick closed and this causes the problem

Jan 18, 2012 | Hotpoint Dishwashers

1 Answer

Hello my hotpoint dwf33 doesnt clean the bottom drawer properly the top one is ok

Sounds like the spray arm is blocked with crud - or the feed to it is.

The spray arm can pulled downwards and away for cleaning by hand.

Sep 15, 2011 | Hotpoint 24 in. DWF33 Built-in Dishwasher

1 Answer

Our dishwasher made a loud pop the other night, and there was a smell of burning plastic/rubber. Since then it has stopped working. No fuse was blown or tripped it seems to be local to the machine. I...

You would probably need a whole new motor but the nwith the smell of plastic you may also have a burn hole in the tub. Your best bet is to replace the whole thing. Sorry

Aug 03, 2010 | Hotpoint 24 in. DWF33 Built-in Dishwasher

1 Answer

Our hotpoint DWF33 Aquarius seems to be going through it's cycle normally but at the end of the program the dishes are not clean, the tab drawer has opened but the tab is still hole. and there is no steam...

i removed the drain cover in the bottom of the dish area ( near the salt fill cap )and cleaned it out. poured boiling water in and closed the machine and ran it with the hottest setting, empty.
this seams to have cured it

Oct 10, 2009 | Hotpoint 24 in. DWF33 Built-in Dishwasher

1 Answer

Hotpoint DWF33 doesn't start

yes... check the wiring to the unit... get underneath your unit and make sure that a wire is not "grounding out" by making contact with a metal part down there on a section of unjacketed wire... this would definately trip your breaker and can blow wires apart with a pop.

there may be enough contact to get the initial display you describe... make sure all the wires are insulated properly and wire nutted together securely before resetting your breaker and checking the unit again.

Sep 02, 2009 | Hotpoint 24 in. DWF33 Built-in Dishwasher

1 Answer

Hotpoint aquarius dwf33 does not always work?!!

I Had this problem its to do with dry joints on the circuit board, solution, resolder all suspect bad joints even though they might look alright especially all those that have heavy electronics connected to the board that could get vibrated.
Peter B

Mar 25, 2009 | Hotpoint 24 in. DWF32P Free-standing...

1 Answer

Drain Hose

tilt machine back and remove bottom plate. drain hose is connected direct to drain pump

Jul 06, 2008 | Hotpoint 24 in. DWF33 Built-in Dishwasher

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

129 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers


Level 3 Expert

4342 Answers

Are you a Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides