Question about Panasonic PT-47WX49 47" Rear Projection Television

4 Answers

I have a panasonic tv which i think is a DV3. Somewhat annoyingly it insists on displaying the screen as the wrong size. more detail? Ok the screen display essentially misses about an inch all round the screen. this has got annoying and i cannot find the settings to change the screen size. The picture Menu Viewing Mode does nothing that i can tell The setup menu does not seem to offer any help either. What am i doing wrong?

Posted by on

4 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 6,487 Answers

Try checking this link http://panasonic.jp/support/global/cs/tv/faq/ww/ans/a5.html

Hope that helps.....

Posted on Jun 29, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 848 Answers

Some little magnets either on swivels around the yoke or glued to the CRT. If these shifted, the the edges may have gotten messed up - wiggles, dips, concave or convex shapes. There may be a doxen or more each mostly affecting a region around the edge of the raster. However, they will not be totally independent

Posted on Jun 29, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,879 Answers

Greetings,

Please post the exact model of your Panasonic TV so that we can assist you better.

Keep us posted and thank you for using our service.
FixYa for all your troubleshooting needs.

Posted on Jun 29, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Expert
  • 1,257 Answers

Check for any reset button on the remote of your t.v..........set it to default setting and see if this trick works or not.......

thanks and good luck

D.i.i.i.p

Posted on Jun 29, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to reset the hour meter on a panasonic pt-52lcx16


Panasonic Projection TV Lamp Timer Reset
Your lamp will probably last a lot longer than the TV thinks it should. This procedure will reset the lamp timer so you don't have to look at that annoying message every time you turn your tv on. Remember that the "lamp" indicator light on the lower left of the set will stay on until the lamp is actually replaced. I had to buy a replacement lamp to get this information, could not find it anywhere for these model numbers.
Press the volume down button on the projection display and hold down the zero button on the remote control at the same time for more than 5 seconds. When the reset procedure is complete, a message will display that the lamp timer was reset to zero.
This procedure will work for Panasonic models: PT-52LCX66 , PT-56LCX66 , PT-61LCX66 , PT-52LCX16 , PT-56LCX16 , PT-61LCX16

Jul 20, 2014 | Panasonic PT-52LCX16

2 Answers

I have a DLP Panasonic tv. The lamp indicator is red.Does this mean the lamp will burn out soon. If so where can I BUT A NEW LAMP.


there could be a possible problem on the convergence module, this is very common problem on the projection tv, kindly check the resistor & capacitor on that area.

let me know,

micro

Jun 30, 2008 | Panasonic Televison & Video

1 Answer

How to reset the lamp meter on a panasonic pt-52lcx16


Panasonic Projection TV Lamp Timer Reset
Your lamp will probably last a lot longer than the TV thinks it should. This procedure will reset the lamp timer so you don't have to look at that annoying message every time you turn your tv on. Remember that the "lamp" indicator light on the lower left of the set will stay on until the lamp is actually replaced. I had to buy a replacement lamp to get this information, could not find it anywhere for these model numbers.
Press the volume down button on the projection display and hold down the zero button on the remote control at the same time for more than 5 seconds. When the reset procedure is complete, a message will display that the lamp timer was reset to zero.
This procedure will work for Panasonic models: PT-52LCX66 , PT-56LCX66 , PT-61LCX66 , PT-52LCX16 , PT-56LCX16 , PT-61LCX16

Jul 20, 2014 | Panasonic Pt-52lcx16-b Replacement Rear...

1 Answer

How to reset the meter on a panasonic pt-52lcx16


Panasonic Projection TV Lamp Timer Reset r
Your lamp will probably last a lot longer than the TV thinks it should. This procedure will reset the lamp timer so you don't have to look at that annoying message every time you turn your tv on. Remember that the "lamp" indicator light on the lower left of the set will stay on until the lamp is actually replaced. I had to buy a replacement lamp to get this information, could not find it anywhere for these model numbers.
Press the volume down button on the projection display and hold down the zero button on the remote control at the same time for more than 5 seconds. When the reset procedure is complete, a message will display that the lamp timer was reset to zero.
This procedure will work for Panasonic models: PT-52LCX66 , PT-56LCX66 , PT-61LCX66 , PT-52LCX16 , PT-56LCX16 , PT-61LCX16

Jul 20, 2014 | Panasonic Pt-52lcx16-b Replacement Rear...

1 Answer

Rangs tv service mode


If you wish to know more details surf this site for more details. Service mode entry and adjustment procedure to many brand televisions are given in detail. Search for your TV brand name by its search box at the upper right of the display window. You can get a solution. More than Nine Lakh viewers cannot be wrong.

May 06, 2013 | Samsung HCN653W 65" Rear Projection...

1 Answer

Model - pt53wx42f Owned since new Repairs 1) 1998 - No power - PS Replaced 2) 2002 -Convergence slowly decreased picture size - Convergence circuitry replaced - operation OK Current...


Projection TV sets are known to have two common problems. The first problem that is common to these sets is convergence failure. When this happens the TV will usually look 3D, Wavy/Distorted, etc. It may also shutdown and blink an error code.

The second common problem with Projection TV sets is dull video, halos around objects, white looking video, or red overpowers the screen. This is commonly caused by the fluid in the lens being clouded over.


You can find more details and solutions here on Fixya at the following link below. Or click HERE

3d884ac.pnghttp://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dul

Sep 16, 2010 | Panasonic PT-53WX42 53" Rear Projection...

3 Answers

Panasonic pt-52lcx65-k color problem


I have the same problem. i called panasonic they said it was a on
going problem and they would send out a repair tech no charge to
fix problem.give them a call 1-888-843-9788

Jan 04, 2010 | Panasonic PT-52LCX65 44" HDTV

1 Answer

HI, just bought a digital hard drive recorder. All working well apart from the fact that EC1/ RGB is permenantly on display when the box is on, and showing on all recordeings. Panasonic Viera tv, how do I...


The only way out of this is to reset the TV back to 'shipping condition'. Go to Analogue Mode and then press Menu. In SETUP pick 'shipping condition' and ok your way through. Then switch off and back on again after a minute, and let it retune etc.

The annoying screen messages now disappear after a couple of seconds. Viola

Sep 27, 2008 | Televison & Video

1 Answer

TV Picture problems


replace all caps in vertical area, if problem stays, try replacing pumpup diode and vertical. if still same problem check drives goin to the vert, and vcc goin to it.

Apr 09, 2008 | Televison & Video

Not finding what you are looking for?
Panasonic PT-47WX49 47" Rear Projection Television Logo

112 people viewed this question

Ask a Question

Usually answered in minutes!

Top Panasonic Televison & Video Experts

 Grubhead
Grubhead

Level 3 Expert

4678 Answers

The Knight
The Knight

Level 3 Expert

69736 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Panasonic Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...