Question about Whirlpool Ultimate Care II LSQ9564J Top Load Washer

1 Answer

Ultimate Care II - Rinse Cycle does not start

I have a Whirlpool Ultimate Care II Model - LSQ8511KQ0 washer. The clothes wash fine until it reaches the rinse cycle. After the water is full, the rinse cycle does not start and nothing happens. Please help !!!

- Vipul

Posted by on

  • Dr Hoff Aug 12, 2008

    I had same problem. Took back control panel off( 2 screws in back), then disconnected the cable that went from the panel to the machine. Then followed that cable to the little hole near where you throw close in. Remove it(two screws). Get that part from appliance store. Have the model # from the machine. I have an Ultimate Care III. Put back together. close the lid. boom. The part is called a "lid switch" good luck

  • Anonymous Sep 28, 2008

    rinise cycle does not start, manually advancing does not work either.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 481 Answers

Sounds like a lid switch problem. is there a clicking noise when you open and close the lid?
if not then the lid switch may need to be replaced; inexpensive.
this could also be caused by a bad timer.
also try a different speed for the rinse cycle, it may be a bad motor and it is not going into a certain speed. instead of gentle or slow speed try fast or normal, something like that.

Posted on Jun 28, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will not spin on any rinse cycle


Hi, This washer does not have a belt. While the washer is agitating, if you lift the lid will it stop? Some models will agitate but not spin if the lid is up. It sounds to me like the lid switch might be going bad.
If you will get me a model #, I can look this up for you and give you a better idea.

Vic

Jul 05, 2009 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

Whirlpool Ultimate Care II Washing Machine Rinse cycle not workin


Most of these spin related problems are attributed to a lid switch malfunction. A washer that fills and doesn't do anything, or stops right after the wash cycle and then does not advance to the rinse cycle and drain is commonly caused by a lid switch. The lid switch is usually mounted under the washer top casing, on the right hand side on most top load models. It is activated by a plastic piece on the lid (called a "Lid Strike") through a small hole on the rim of the wash tub opening. In many cases the lid strike breaks off the lid, or the lid switch becomes loose and no longer makes contact. Inspect the lid to make sure the lid strike is still intact, and then inspect the mounting screws (adjacent to the small opening on the wash tub rim) and make sure they are snug. If you determine the switch to be defective, the following link explains how to replace one:

http://www.fixya.com/support/r385198-replacing_lid_switch

If the switch requires replacement, a new one can be purchased on line at searspartsdirect.com, pcappliancerepair.com, repairclinic.com, appliancepartspros.com. Just use your model number as your search criteria. All these sites offer competitive pricing, so shop all them for the best price.

Let me know if you need further assistance. I hope this helps you.

Jun 30, 2009 | Whirlpool Ultimate Care II LSQ9564J Top...

2 Answers

Washing machine starts by itself


going through to the next wash not na normal function, perhaps the machine is advancing to an extra rinse cycle?? this EXTRA RINSE will start after the normal wash is complete, i would check your dial settings perhaps some one has mistaknely switched extra rinse "ON". if htis os not tyhe case the n i would jave to blame a faulty timer mechanism and you would need to replace the timer

Feb 15, 2009 | Whirlpool Ultimate Care II LSQ9564J Top...

1 Answer

Whirlpool Ultimate Care II


sounds like a broken coupling.
it probably don't agitate either.

Oct 28, 2008 | Whirlpool Ultimate Care II LSQ9564J Top...

1 Answer

Washer won't cycle through...


The cycle timer may be defective and will need replaced. Hope this was helpful.

Oct 11, 2007 | Whirlpool Ultimate Care II LSQ9549L Top...

2 Answers

Agitator


if its a 2 piece agitator.. the gears in top of agitator is stripped out.. change gears be like new....spin top countor clockwise if it dont grap.. gears bad

Sep 28, 2007 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

Whirlpool Ultimate Care II GSQ9669LGO


Sounds like you may need to replace the timmer

Jun 06, 2006 | Whirlpool Ultimate Care II GSQ9669L Top...

Not finding what you are looking for?
Whirlpool Ultimate Care II LSQ9564J Top Load Washer Logo

Related Topics:

407 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...