Question about Siemens Computers & Internet

Open Question

I have a Fujitsu-Siemens EDA, that is stuck on the align screen page. I have attempted a reset, a warm reset and a hard reset (pressing suspend/resume button, calendar button whilst pressing stylus into reset button) and all to no avail. The EDA always restarts on the align screen page and I cannot get off this psge! Any ideas would be greatly appreciated. Thanks.

Posted by on

4 Suggested Answers

SOURCE: k jam screen align does not work after hundred or so attempts

Well I had the exact same problem with my K-Jam but my dead zone/spot was more specific to the centre of the entire screen. I also resorted to hard resetting my phone to try and resolve the problem and guess what is the first required action, screen alignment. I tried applying pressure to the centre of the screen for it to take the first setting but it wouldn't. I called Imate and spoke to a technician and their only option was for me to replace my LCD touchscreen mechanism. I put my phone off for and never attempted the screen alignmentfor about three days (the screen was faced downwards for this period). One morning after awaking I put the phone on and tried aligning the screen with some pressure using my index fingers nail and the screen was aligned and I completed the setup successfully and to this day I dont think that I would resort to resetting the phone again for this problem.

Posted on Aug 07, 2007

DOREEN1
  • 51 Answers

SOURCE: Application Buttons

take the battery off for 15 seconds then put it back... try doing this atleast once a week. hoping this will help your problem. goodluck

Posted on Jan 21, 2008

  • 1 Answer

SOURCE: Screen not responding to stylus

SOLUTION:

KEEP PRESING CALENDAR+MAIL+POWER BUTTON
AND INSERT STYLUS IN RESET BUTTON

Posted on May 30, 2008

rahbeigh
  • 50 Answers

SOURCE: my htc touch p3450 is stuck on

the only solution here can be a firmware upgrade but that may damage your warranty doing yourself.. i can suggest try connecting it with your computer with the usb cable and leave it like that for a while. then let it drain out its battery.
if it does not work, keep it off for some hours maybe a day, still does not work then use your warranty to get it fixed.

Posted on Dec 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My System Fujitsu Siemens Scaleo P cannot boot windows and doesn't proceed after display of Fujitsu Siemens Logo (Where it says Press F2 to Enter Setup).


I would take it back to the place of purchase, it is clear the window installation was not completed, a manufacture oversight.

Jun 18, 2012 | Fujitsu LifeBook AH531

1 Answer

Could you tell me what has to be done when the only item appearing on the screen is MC70?


Resetting the EDA

There are two reset functions, warm boot and cold boot. A warm boot restarts the EDA by closing all running
programs. A cold boot also restarts the EDA, and also resets the clock. Data saved in flash memory or a memory card is not lost.
Perform a warm boot first. If the EDA still does not respond, perform a cold boot.

Performing a Warm Boot - Soft reset

Hold down the Power button for approximately five seconds. As soon as the EDA starts to boot release the Power button.

Performing a Cold Boot - Hard reset

To perform a cold boot simultaneously press the Power button and the 1 and 9 keys.



symbol_mc70_hard_reset_soft_reset.jpg

Dec 03, 2010 | Zebra Symbol MC70 HandHeld Mobile Computer...

1 Answer

Fujitsu Siemens Amilo - Won't boot


could be hard drive failure,or you might try to reinstall windows before bying a new hardrive,but before any of that go to the BIOS and make sure that the boot order is right usualy hard drive first

Apr 05, 2010 | Fujitsu Siemens AMILO Pro V1000 Notebook

1 Answer

The screen is stuck on the align screen i reset the phone and attempted to reload windows mobile and when the align screen came up i tapped it but it wont go away


Did you perform a hard reset? To do this:

  1. Slide open the device to expose the QWERTY keyboard.
  2. Press and hold the center of the 5-way navigation pad.
    action_button-01.jpg
  3. While holding the center of the 5-way navigation pad, use the stylus to gently press and release the reset button.
    reset_button-01.jpg
  4. When Clearing Data... appears on the screen, release the center of the 5-way navigation pad.
  5. When prompted, tap the screen to setup the device.

Sep 07, 2009 | Samsung SCH-i760 Smartphone

1 Answer

I have a Pocket PC, Fujitsu Siemens N520. Tried to hard reset it and now it's stuck at the climbing people image. Tried everythinh i knew. hard reset, soft reset, battery out for 5 mins. Nothing. Please...


Fujitsu Siemens have a tech online contact point where you can advise them of the problem. The Hard Reset has always worked for me - do you get the option of "Factory Default" show - if not then you have not done the hard reset properly. Depress Enter and use the stylus to press the reset button in the rear. Good luck

Aug 11, 2009 | Fujitsu Siemens Computers & Internet

1 Answer

The touch screen does not appear to be working


needs to be replaced , if it does not respond to ur taps have u tried aligning the screen does it work at all or no area is responsive on screen then u can try hard resetting it first but after that it will be guaranteed that ur touch panel is faulty which seems like to me

but one thing u shud now do all data will be lost in factory reset process and if ur touch panel is faulty u will stuck up in initial aligning process so pls backup first b4 going ahead sync contacts and sms calender an stuff then try this

hard rest factory default settings = when ur set is switched off press both buttons call and end key and then press power button on upside of pda for like 5 sec screen will appear asking to format all data take out ur card if u dont want to format that now confirm by pressing the centre action button in 4 side joystick and go

if u are stuck at align process then it is now pretty sure that ur TOUCH PANEL / also called DIGITIZER is faulty u can get it replaced around 60 $ or so

pls rate me fixya for my diagnosis if u like

Mar 05, 2009 | HTC Touch P3450 Smartphone

1 Answer

Forgot password


Performing a Clean Boot
THIS WILL TAKE IT BACK TO THE FACTOR SETTINGS
A clean boot resets the EDA to the factory default settings. All data is the Application folder is retained. You must
download the Clean Boot Package file from the Support Central and install on the EDA.
NOTE When the EDA powers up after inserting a battery for the first time, the device boots and powers on
automatically.
CAUTION A clean boot should only be performed by an authorized system administrator. You must connect the EDA
to AC power during a clean boot.
Removing AC power from the EDA during a clean boot may render the EDA inoperable.
To perform a clean boot:
1. Download the Clean Boot Package from the Support Central web site. Follow the instructions included in the
package for installing the package onto the EDA.
2. Simultaneously press the Power button and the 1 and 9 keys.
3. Immediately, as soon as the device starts to boot and before the splash screen is visible, press and hold the
left scan button for a few seconds.
4. Insert the EDA into a powered cradle.
5. The EDA updates and then re-boots.
6. Calibrate the screen.
Waking the EDA
The wakeup conditions define what actions wake up the EDA. These settings are configurable and the factory
default settings shown in Table 1-3 are subject to change/update.
Table 1-3 Wakeup Conditions (Default Settings)
Status Description Conditions for Wakeup
Power Off
(Suspend Mode)
When the EDA suspends by pressing
Power, these actions wake the EDA.
1. Power button is pressed.
2. AC power added or removed.
3. Cradle/cable connect or disconnect.
Key or scan button is pressed.
Real Time Clock set to wake up.
Incoming phone call (MC7004/94/95 only)
Auto Off When the EDA suspends by an automatic
power-off function, these actions wake the
EDA.
1. Power button is pressed.
2. AC power added or removed.
3. Cradle/cable connect or disconnect.
Key or scan button is pressed.
Real Time Clock set to wake up.
Incoming phone call (MC7004/94/95 only)

Apr 11, 2008 | Symbol MC70

3 Answers

Hard Reset


To do a Hard Factory Reset:
Simultaneously press the Suspend/Resume (END) button whilst pressing the stylus tip into the reset opening.
end_button.jpg reset_button.jpg Keep them held until the screen comes back on. Then release the buttons
You will get the Boot options:
  • CLEAN REGISTRY - This resets the device to factory settings, losing applications but keeps the data intact.
  • FACTORY DEFAULTS - This completely wipes everything and resets the device back to it's factory defaults.
  • SKIP
    Try Clean Registry first.
  • Jan 13, 2008 | Fujitsu Siemens Pocket LOOX T830...

    Not finding what you are looking for?
    Computers & Internet Logo

    Related Topics:

    176 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Siemens Computers & Internet Experts

    Prashant M
    Prashant M

    Level 3 Expert

    2260 Answers

    Les Dickinson
    Les Dickinson

    Level 3 Expert

    18381 Answers

    john smith

    Level 2 Expert

    381 Answers

    Are you a Siemens Computer and Internet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...