Question about Audio & Video Receivers

1 Answer

Hi there, I work for a Pontiac Buick GMC dealer and I was wondering, Our new Pontiac G8 is equipped with a Blaupunkt 11 speaker system and I just want to know were all 11 speakers are as I can only find nine!!!

Posted by on

  • nashville-18 Jun 29, 2008

    Thanks but that's not it I've been counting all the tweeters as well!!! This car is also badged as the Holden Commodore in Austrailia, I've checked online for wiring diagrams and everything and there seems to be nothing out there unless I'm looking in the wrong places or something!!! Thanks for trying though!!!

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 520 Answers

They are probably counting tweeters as seperate speakers.

Posted on Jun 28, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Have inherited a ferguson record and tape combination player studio 20D and its a wonderful piece of equipment but I cannot get any sound out of it and I was wondering if i HAVE TO BUY SPEAKERS for it...


Most of those old relics had built-in speakers, which may be dead by now or simply disabled.

Barring that, the audio output could be run to any audio device (EXCEPT PHONO which is reserved for turntables).

There are many open-reel forums online where you might post questions for enthusiasts to answer.

May 24, 2011 | Audio & Video Receivers

1 Answer

Hi, wondered if you could assist please. I have a Yamaha SH DT510 Set top box that I purchased back in 2003 with my home theatre equipment, however, have experienced a problem with one of the speaker or...


What is your actual 'problem'? There's nothing in a set top box that would pick one speaker to fail unless it was, say, one of the two optional channels like the center or sub, which probably need to be defined internally. I imagine the menus would lead you there.

Otherwise, your audio equipment would be where I would start the troubleshooting.

Oh, btw, did you mean PIONEER SH DT510?

Jan 11, 2011 | Audio & Video Receivers

1 Answer

My model is RX-V665...not sure what the BL stands for... anyway...no sound from the subwoofer. Pull the RCA wire from the back of the receiver and touch it with my finder and you hear a buzz from the...


HI,
first of all select ur sub woofers auto mute (auto power off ) switch to off position.
then connect the mic and calibrate ur system one more time. after calibration select it to on position. u will surely get it work. if need any further assistance feel free to contact through fixya.
ok

Dec 31, 2010 | Yamaha RXV665BL Receiver

1 Answer

My reciever plays then cuts out


They don't overload from missing speakers. I'm curious, what buggered the one speaker?

Examine all of your speaker wires carefully to be sure no unintended contact is made between them and anything else.

Is "overload" being displayed?

“OVERLOAD” starts flashing on the display.

Speakers are overloaded because of high volume.

1. Press STANDBY/ON on the front panel to turn off the receiver.
2. Stop the playback source.
3. Turn on the receiver again, and adjust the volume.
----------------
Speakers are overloaded because of short circuit of speaker terminals.

Press STANDBY/ON on the front panel, then check the speaker wiring.

If “OVERLOAD” does not disappear after turning on the receiver again, unplug the AC power cord, then plug it back in again.
If speaker wiring is not short-circuited, contact your dealer.

Mar 31, 2010 | JVC RX-6042 Receiver

2 Answers

Want to buy YAMAHA RXZ11 receiver but where to get yamaha recomen


The Yamaha RXZ-11 does not come with any set of speakers. Infact there are no "recommended 11.2ch speaker kits". You are advised to purchase top quality Yamaha speakers. Better yet, build your own 11.2 kit. Its not too hard (internet helps) and its tremendously fun!

Jan 16, 2009 | Yamaha RX-Z11 11.2 Channels Receiver

1 Answer

RECEIVER WORKS FINE WITH THE RADIO NOT THE TV.


correctly connected to output on tv ? ie red and white left and white and not yellow (video)??

Dec 08, 2008 | Yamaha HTR-5860 Receiver

1 Answer

Speakers


If I understand you right, you have 7 speakers on 7 different channels.
When you have just 1 speaker connected it sounds fine, but any time you add more speakers it shuts down, or does it sound fine until you have all 7 of the speakers connected.

Bare with me, and we will figure this out. It is a very diificult job trying to troubleshoot something that is not in front of you.

After this post, it will be about an hour or so before you will hear from me again, I will be on my way home from work.

Is this a 5.1 surround system or is it listed as 7.1?

Do have have any speaker outputs with more than 1 speaker connected to it.

If this is a 5.1 system, do you have speakers connected to the "A and "B" speaker jacks?

What kind of speakers are they, and do they say on the back where you connect the speaker wire what ohm rating they are. Most speakers for your home are 8 ohms.

in case you were wondering what a 5.1 and a 7.1 system is:

the 5.1 system has front right, front left, center, rear right, rear left and the .1 is for the sub-woofer that is normally a RCA jack output on the back of the receiver

The 7.1 has all those same speaker outputs plus it has a surround back with right and left channel.

I will get back to you in about an hour or so.

Jun 23, 2008 | Audio & Video Receivers

1 Answer

Set-up problem with sound and speakers


I sent this TX-SR605 system to an authorized dealer for repair. It seems like it is a very simply problem - the internal set-up mic jacket closed circuit, so the system think the set-up mic is always plugged in (even when physically unplugged it, the system still detect plugged in). And it enters the automatic speaker setup and never quit.

Now I have the receiver back home and tested it. Everything worked O.K. now. It is a pity that this new-bought equipment (just one month) need repair for just a small action of plug in a mic ( I swear I plugged it in very tenderly). It is shame for such a unreliable performance happened on brand name like ONKYO. How can you be confident for an equipment failure in one month.

Dec 25, 2007 | Onkyo TX-SR605 Receiver

1 Answer

OVERLOAD


HOW MANY SPEAKERS ARE YOU RUNNING? IF you are running more than TWO speakers, the very FIRST thing to check is to make certain ALL of your speakers have an IMPEDENCE of 8 OHMS. Virtually all speakers of even modest quality will include this specification on a label on the back of the speaker. You CANNOT run more than (2) TWO speakers with 4 OHMs impedence on ANY amplifier (technical discussion too long!) [NOTE: Some Pioneer equipment have internal overload protection systems to prevent permanent damage. However, you cannot re-set these systems yourself. Your dealer or authorized HK service center must do this.] But, before you take your unit in for service, there is one more "test": check for shorted and/or mis-connected/disconnected speaker cables/wires. Visually inspect connections at the receiver and speakers first. You might find something obvious! If everything looks okay, then disconnect ALL of the speakers; and reconnect and test them one at a time (at relatively low volume.) For example, reconnect the left front speaker, test the system; THEN add the right front, test the system,and so on, ADDING one more speaker each time - FIRST MAKING SURE EACH OF THEM HAS AN IMPEDENCE OF AT LEAST 8 OHMS! IF there is a short (or bad speaker) this will help isolate it. Hopefully one of these "fixes" will work for you. GOOD LUCK!

Jul 15, 2007 | Pioneer VSX-D511 Receiver

1 Answer

Protection code 11


The very FIRST thing to check is to make certain ALL of your speakers have an IMPEDENCE of 8 OHMS. Virtually all speakers of even modest quality will include this specification on a label on the back of the speaker. You CANNOT run more than (2) TWO speakers with 4 OHMs impedence on ANY amplifier (technical discussion too long!) [NOTE: Some Sony equipment have internal overload protection systems to prevent permanent damage. However, you cannot re-set these systems yourself. Your dealer or authorized HK service center must do this.] But, before you take the unit in for service, there is one more "test": check for shorted and/or mis-connected/disconnected speaker cables/wires. Visually inspect connections at the receiver and speakers first. You might find something obvious! If everything looks okay, then disconnect ALL of the speakers; and reconnect and test them one at a time (at relatively low volume.) For example, reconnect the left front speaker, test the system; THEN add the right front, test the system,and so on, ADDING one more speaker each time - FIRST MAKING SURE EACH OF THEM HAS AN IMPEDENCE OF AT LEAST 8 OHMS! IF there is a short (or bad speaker) this will help isolate it. Hopefully one of these "fixes" will work for you. GOOD LUCK!

Jul 14, 2007 | Sony STR-DA2000ES Receiver

Not finding what you are looking for?
Audio & Video Receivers Logo

Related Topics:

174 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audio & Video Receivers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

The Knight
The Knight

Level 3 Expert

68157 Answers

yadayada
yadayada

Level 3 Expert

60667 Answers

Are you an Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...