Question about Onkyo TX-SV525 Receiver

2 Answers

Onkyo TX-SV525 Receiver subwoofer pre out no sound

When I connect my KEF psw 2000 on the subwoofer pre out connection of the TX-SV525 Receiver here is no sound coming out of the subwoofer ( the subwoofer is tested and perfect).
In the manual is written that I have to turn on "a speakerA switch" to "on" situiated on the front panel.

What do I have to do to make my subwoofer working?

greetings,

Pieter

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 624 Answers

Yes turing on the "A" speaker is required for the Onkyo, but that only turns on the 2 front speakers in the "A" speaker jacks.

You may also need to check and see if the Onkyo has a menu selection in the setup menu that will turn on the sub woofer output on the back of the receiver.

I have seen on countless occasions where people just have a hard time finding that sub woofer option on their receiver.

I do not have the manuals for this Onkyo, so I can not tell you the exact way to find it.

I have been repairing surround receivers since they have been on the market and beleive me, you are not alone in this situation.

Sometimes it seems like you need a Phd. in programming or something similar just to firgure out how to set one of these up.

The solution should be in your owners manual, with the problem then being, just where in the manual. Go slowly thru it paying the closest attention to anything about set up procedures.

I have also seen at times where the setup for the sub-woofer is not listed as sub-woofer, but as "LFE" (low frequency effect) . So keep your eyes open for that.

something else, your sub woofer may have an auto turn on. That means it will only turn on if it detects an input signal. Make sure yo uhave the volume up enough on the receiver to trigger that auto turn on if yours has one.

I would like to have been more help, but without the manuals I can only give you general type thngs to look for. These type of receivers are all so different and all so complicated to operate. The days of just turning on a stereo, selecting your source and turning up the volume seem to be over.

Let me know if you need any more assistance from me.

Dave

p.s. Very nice system you have, when you get the Kef working I think you are going to just love this system. and Onkyo has the best quality receivers in their price range.

Posted on Jun 27, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I hook up BIC F12 subwoofer to Onkyo TX-DS838 receiver? Will the receiver power the subwoofer and other speakers?


Get a RCA cable and connect from your amp where it said Sub Woofer in the Pre Out box in the back of the amplifier top left hand side and take it to the "Sub In" located in the back of your Sub woofer bottom right hand (White round connector).
Good Luck!

Aug 06, 2014 | Onkyo TX-DS838 Receiver

1 Answer

I have a Yamaha HTR 3063 reciever and I just got a PSW 2000 Kef sub and I can't get the sub to WORK NO MATTER WHAT I DO PLEASE HELP


That is a potentially great combination. I have a Yamaha receiver but I am not familiar enough with Kef to know but is it possible your receiver expects to be connected to a powered sub. Are you sure the Kef works by itself? Have you checked to see whether the receiver subwoofer output works with another speaker? Could receiver mode selection be a factor? My Yamaha switches various functions on and off depending upon your preference.

For what it's worth, the troubleshooting section of my Yamaha manual says a subwoofer no sound problem can be caused by selecting MAIN LFE/BASS OUT on the SET MENU when Dolby or DTS material is being played or selecting SWFR when a 2-channel source is being played. Something has to work!

Sep 10, 2012 | Audio Players & Recorders

1 Answer

Can you hook an iPod up to an Onkyo TX-SV525 receiver?


yes. use adapter cable, connect iPod to an input on the receiver like CD or AUX and select this input on the receiver. See below pic.alexander404_5.jpg

you can buy these adapter cables online or at Radio Shack etc.

Apr 29, 2011 | Onkyo TX-SV525 Receiver

1 Answer

Hello ! I'm not sure how to connect my kef psw 2500 sub to my yamaha amp. I've got a subwoofer out on my amp but there's 4 inputs on the sub and I don't no which one to use ! Please help as getting...


Just for clarity, I need to explain what the four inputs are on the KEF subwoofer. There is a left and right RCA input which is the input signal to the subwoofer and there is a left and right RCA output which is the High Pass output from the subwoofer.

On the back of the Yamaha receiver, you said you have a subwoofer output. This output is most likely the mono subwoofer part of the home theater system and can be used if you like. The left right signal input into the KEF is summed into mono so if you only connect one channel you will basically reduce the signal level by 1/2 (-3dB) but it will work fine.

Alternatively, if your Yamaha receiver has monitor out and monitor in, you can run the monitor output signals to the subwoofer and you can then run the high pass outputs from the subwoofer back to the monitor in. This will give you the subwoofer and provide a smoother signal matching with your audio system.

It is not always easy to connect the subwoofer up to an integrated receiver/home cinema system using the high pass channels of the subwoofer as you don't always have access to the analog output and input of the front channels. In this case, just use the Subwoofer output or just the monitor out only.

I hope this solution is helpful.

Dec 03, 2010 | KEF Audio PSW 2500 Subwoofer

1 Answer

Im having trouble with connections from kef psw 1000 sub to onkyo tx sr506 amp. sub is making a bit of a humming noise but not getting any proper sound through. dont know what im doing wrong. can anyone...


Have you got the sub defined to the Onkyo correctly? Try conencting the sub's input to one of the Tape Out connectors and play some FM through it. That will prove if the sub is alive. The nwe can troubleshoot the correct failing device.

May 03, 2010 | KEF Audio PSW 1000 Subwoofer

1 Answer

OVERLOAD


First of all the KEF is a powered sub which means that it wants a line level signal NOT a speaker level. Send the signal from a tape output or pre-amp output to the sub input. The overload is because the impedence load for the speaker output is too low and looks like a short to the amp. Continued attempts to connect the system as described will result in damage to the output section of the amp.

Please let me know if you need more info.

Dan

Feb 03, 2010 | Technics SA-DX750 Receiver

1 Answer

I just bought a KEF PSW2500 subwoofer and am trying to connect it to a Yamaha v663 receiver. However, I went from a subwoofer pre-out 1 to the right line in on the sub. I don't hear any sounds from the...


HI,go into the yam setup menu and make sure you have the sub turned on and cross over set to about 80hrtz if this suits your speakers,set sub level to about -5 on amp and say half way on the sub,this should work if not pull out sub cable at amp and touch the end,you should get a hum,if not you may have no power,faulty cable or sub.
PS>make sure you are pluged into the sub PRE OUT and NOT the six channel in.
Hope this helps.
CABLE GUY.

Apr 19, 2009 | KEF Audio PSW 2500 Subwoofer

1 Answer

Can you tell me if my receiver is digital? The model is TX-SV525. My E-mail is kenoman28@gmail.com. Thank you.


your tx-sv525 audio video control tuner amp is has full analog connections therefore it is analog.

Mar 03, 2009 | Onkyo TX-SV525 Receiver

1 Answer

No Signal on sub preout on my Onkyo TX-SR703 AVR


Well the next step would be to make sure that all the settings are set to subwoofer yes, and set your crossover as well.  The amp usually has a crossover which tells the microprocessor which frequencys to send to the sub.  

Jan 06, 2009 | Onkyo TX-SR703 Receiver

2 Answers

Onkyo TX-SV525 Receiver


Ve a http://audio.manualsonline.com,Suerte.

Mar 29, 2008 | Onkyo TX-SV525 Receiver

Not finding what you are looking for?
Audio Players & Recorders Logo

776 people viewed this question

Ask a Question

Usually answered in minutes!

Top Onkyo Audio Players & Recorders Experts

Dennis McCollum

Level 2 Expert

137 Answers

 Grubhead
Grubhead

Level 3 Expert

4751 Answers

The Knight
The Knight

Level 3 Expert

71672 Answers

Are you an Onkyo Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...