Question about DVD & Blu-Ray Players

1 Answer

I have a G2G DVD-708 player and the video on the primary screen attached to the player unit is not showing a picture. The picture comes on fine on the second, remote screen. The volume control and remote control sensor work on the primary screen controls.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

The problem with that unit is an easy fix. Simply take apart the upper half of the unit (the screen). Its two screws on front, four on the back. Carefully seperate the unit and note that the wire set that runs across the bottom of the screen has come unplugged. Reconnect the wire to the circuit board and reassemble. This is common due to the rotating screen. Email me if this helps at xtremediesel_1980@yahoo.com

Posted on Jan 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My panasonic DMR-ES20 has sound but picture? have unpluged but still no picture???


maybe you unit is in progressive mode try to reset it by holding stop and play/x1.3 button at the same time for about 5 seconds.

Apr 22, 2014 | DVD & Blu-Ray Players

1 Answer

I get only a white screen when I put in the DVD. It shows power to the unit. There is no other aactivity on the screen.


The portable LCD screen panel that attach to the potable DVD player is dead.This DVD player is not repairable except u must replaced the whole LCD screen attachment lcd screen panel itself.Not worth repairing,will cost the same as the cost of a new unit.

Feb 07, 2012 | Polaroid PDM-0824 Portable DVD Player

1 Answer

Audiovox PVS69701 Dual Screen DVD player monitor has blue screen


I had the same problem, and it seems to be a short in the video cable between the two monitors. I can bend my cable until i see the second screen and then tuck it under the headrest. I am currently looking for a replacement cable. I see it at 1800customersupport.com, but will also check the local radioshack since I need it quickly.

Jul 30, 2010 | Audiovox PVS72901 Portable DVD Player

1 Answer

Player works fine, no video on extra lcd screen,audio ok


It can, but unless you have a real good DVD player, it will cost more to fix. It doesn't show you model so I can only give you limited help.

If you paid over $100.00 and it is a HD or Blue -Ray, then you can take it to a repair shop. If not, it would be better to go shopping for what you will pay out to have it fixed.

I am sorry if that is not what you wanted to hear, but, thank you for the chance to help.

Randy
FixYa Support Team

Oct 14, 2009 | DVD & Blu-Ray Players

1 Answer

Picture is not on the screen. I cannot seem to


Alot of times you have to back up the TV to something like LINE 1 or LINE 2. It will not show up with the TV on channel 3. When I attached my VCR, I hit input and line 1 and 2 came up and then the DVD player would play just fine. Try that.

Jul 18, 2009 | GoVideo Go Video DVD/VCR Combo

1 Answer

TV & DVD HookUp (No Box) Can't get picture


As far as I know, my Go Video machine when there was no box involved...

The cable came from the wall to the IN of the Go Video box. Then another cable coming from the OUT of the video box and to the IN to the TV. TV should be on channel 3. As far as I can remember, I don't need to push the TV/VCR button, but instead, have to channel down to below channel 2 on the TV to the LINE/INPUT selection. Once you go there, and the Go-Video machine is on, you should be able to see a clear picture.

You'll push the TV/VCR button if you want to toggle back and forth from the VCR picture to the TV picture (which will be technically blank since it's on the 'line input selection.)

Hope that helps.

Mar 08, 2009 | GoVideo VR3845 DVD Recorder/VCR

1 Answer

No Picture


sounds like the digital video controller went out. you can test this on this unit by using the coax out and connecting to your tv, it seems to have its own video card looking inside the unit, however it is possible it is controlled centrally thorugh the main card in that case you will confirm by it not working and still only gettting sound through the coax.

Feb 21, 2007 | Samsung DVD-R135

1 Answer

No picture


How is the player plugged into the TV set? Are you using the S-video or RCA type plugs? Have you tryed a differant input on a differant TV? It could also be your cables. If you tryed differant cables and a differant input then your problem is a broken connection on the video jack or in the video output processor IC inside the unit and thats not a user fixable problem, Sorry. Good luck

Jul 23, 2006 | Sanyo DWM400 DVD Player

1 Answer

White screen no picture but sound


First thing to check is the ribbon cables for chaffing, or the connection seating. This can cause this symptom. As well as a failing LCD video deciphering circuit and/or motherboard problems. not a bad chance that you'll need to replace the screen/unit. any warranty? Good luck

Jun 06, 2006 | Durabrand DUR7 Portable DVD Player

Not finding what you are looking for?
DVD & Blu-Ray Players Logo

Related Topics:

259 people viewed this question

Ask a Question

Usually answered in minutes!

Top DVD & Blu-Ray Players Experts

kakima

Level 3 Expert

96627 Answers

The Knight
The Knight

Level 3 Expert

68352 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a DVD and Blu-Ray Player Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...