Question about Indesit W 123 Front Load Washer

1 Answer

Indesit wil 103 heater element

How do you replace the heater element do you have to take the drum out

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,462 Answers

No need to take drum out. heater is held by one 10mm nut in the middle of the heater. when tightened, this nut compresses the rubber seal and holds heater in place. loosen the nut. the heater will probably be too tight to remove by hand so carefully use a screwdriver to lever it out

Posted on Jun 26, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Washing machine


I had thi problem.I removed the heater element but there was nothing wrong with it when tested .Do not do this as it is hard to get element back in
What I done was remove the top of machine and pulled connector of temperature knob It was corroded.I sprayed the connection with WD40and shoved it on and off a couple of times and hey presto it worked .Themachine is heating again

May 05, 2013 | Indesit W 123 Front Load Washer

1 Answer

How to fit new eleiment in Indesit DVG622WHUK


Unplug the machine and remove the back plate (5 or 6 screws).
At the bottom of the drum you will see the element.
Best thing to do is take a photo of the wires before removing them.
Undo the screw in the centre of the heater element (not all the way off)
Tap the nut and thread gently till it goes in a little and you should be able to pull the element straight out.
Place the new element in (with nut in similar place) until it sits nicely in the hole.
Then do it up nice and tight and replace the wires making sure they are in the right place and jobs done :)
Replace the back and try it. Should be fine.

Oct 30, 2011 | Indesit W 123 Front Load Washer

1 Answer

Indesit washer dryer starts cycle, waters then


If the heater element is not working, then the cycle will not progress.
You need to test the element to see if it is o/k.
Hope this helps.

Jan 05, 2010 | Indesit Washing Machines

1 Answer

Bearings getting noisy


no need to remove the drum
u just unscrew the screws and spyder wil come and u can change the baring

Mar 07, 2009 | Indesit W 123 Front Load Washer

1 Answer

Bearing noise on Indesit WDG1295


you will have to open the machine lid to see if its a plastic drum or metal.
the metal drum is easier as it has a 'spider asssembly'. remove this after taking off the pulley by taking out the bolts that hold it and bang it off being carefull of the heater element. remove the bearings and seal and refit in reverse order you took it off.
i would not advise replacing plastic drum bearings as they are a pain, removal of the rear of a plastic drum easy but not putting it back !

Feb 01, 2009 | Washing Machines

1 Answer

Indesit WIE167 washing mashine


Remove the rear panel of the washer.
You will see the heater element at the rear of the drum,it has 2 wires going to it.
The thermistor as it is called is located at the end of the element,, unplug the connector on the thermistor. and pull the old one out, refit new thermistor, and connector.
Plz rate my solution.
Thanks.

Jan 06, 2009 | Indesit W 123 Front Load Washer

2 Answers

My indesit WG1230 washing machine does not spin or move drum but water go in and out.


Hi,
With the door open, try spinning the drum, there should be some resistance along with a slight wherring sound. If it spins freely without much sound at all - you probably need a new belt.
If you can feel it driving the motor, you may need new contact brushes for the motor.
If the machine buzzes when it should rotate on program, you need a new motor Run capacitor also.
If no sound - nothing, the motor may need replacing or at least checking.

Nov 05, 2008 | Indesit Washing Machines

1 Answer

Indesit washer


if you mean the wires that go to the back of the drum from left to right= green circle=brown wire pushon tellow/green(earth) square =2 lite blues yellow circle=dark blue if this isnt what you needed please respecify and ill do my best to answer ,ian if you add to this post it will inform me for a faster reply

Nov 03, 2007 | Indesit W 123 Front Load Washer

Not finding what you are looking for?
Indesit W 123 Front Load Washer Logo

Related Topics:

314 people viewed this question

Ask a Question

Usually answered in minutes!

Top Indesit Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

neilmoto

Level 2 Expert

75 Answers

Are you an Indesit Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...