Question about Jackson 24 in. JPX-300H Built-in Dishwasher

1 Answer

New start button?

Hi.  I have had my Jackson for 2-3 years.  So far, so good.  Now the start button sometimes doesn't work and we have to push it several times.  Sometimes if we open and shut the door, it will start when we push it again. Do I possibly need a new button? Please respond to ludvigsbistro@hotmail.com or 907-738-3603. Thank you,  Colette Nelson,  Chef/Owner Ludvig's Bistro, Inc.  Sitka, Alaska

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 38 Answers

Hello Colette,
When a component sometimes works and sometimes doesn't work, it suggests the component itself is functioning correctly. Check for loose wire connections on the door switch, the start switch, and on the cycle-reset switch which is located on the cam-timer assy of the machine (if so equipped). Cam timer assy is behind the kick-plate, under the door.

Posted on Aug 19, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Performa dishwasher will not start. But when I push the "delay" button the power panel lights up and I can change the delay to 2, 4 or 6 hours, change from heat dry to air dry, but I can't get it to start....


Don't know model but it's either a relay , solenoid or contractor not working. Should be a wiring diagram inside panel . Check voltage and sometimes you can smell the faulty part. Appliance part stores have everything you need and probably can advise you on what's wrong w it and the part you need

Mar 01, 2015 | Dishwashers

2 Answers

Hi, my frigidaire pld4375rfc3 stopped working. I


The touchpad has gone bad. common problem with most of the electronic dish washers out on the market today. Replace the touchpad console and you should be good to go.

May 31, 2010 | Frigidaire Dishwashers

1 Answer

Cancel light and rinse only light keep blinking and wont start


Hello,

Hopefully you have resolved your issue. I have not heard of the cancel light flashing issue. I have had problems with the clean light flashing seven times over and over and the control panel will not operate. Here is the solution to that. Maybe it will work for your issue as well.

Open dishwasher door,
Push Hi Temp Scrub button,
Push Saver Dry button,
Push Hi Temp Scrub button again,
Push Saver Dry button again,
All lights on control panel will come on.
Close dishwasher door,
Push Baked on Cookware or Normal Button.
Dishwasher should start and complete cycle.

It is good if you have kids that play video games. Their fingers are used to pushing buttons quickly. I guess this resets the control board. The service guy let me have this info as I used to deliver appliances and work on them somewhat.Hope this helps.

Good Luck,
Tom

Nov 26, 2008 | KitchenAid 24 in. KUDS01FLSS Built-In...

1 Answer

Jackson dishwasher


no there is no seal keep the wash arms clean if the last hole gets stopped up then it will spin backwards and cause it to come off
otherwise go to home depo and get a oring that fist over the threads on the breaing and tighten by hand and you should be good
i have worked on these machines for 12 years

Jun 12, 2008 | Jackson JP-24B Built-in Dishwasher

1 Answer

Flashing quick rinse light on panel


I had the same problem but I found someone wh said that there is a way to reset the dishwasher. I tried it and it has worked so far.

Here is what I did.
Push the Hi-temp and then push the Sani-rinse. Go back and forth multiple times on these two buttons. I found that after a handfull of pushes that a "1" came up on the display. I continued to keep rotating the two buttons and then a "2" came up on the display and the dishwater started it's "drain" phase. I then hit cancel to clear and then I selected the cycle I wanted. The washer started up just as normal at this point.
Good luck!

Oct 24, 2007 | Kenmore 15769 Built-in Dishwasher

1 Answer

Maytag dishwasher mdbh950awb


Sounds like you have a control panel and/or control board issue. Normally when operator functions fail or "halfway" work the main control board, associated keypad, or wiring are the likely suspect. Now...another remote possibility could be the door latch not closing properly. However, this would affect ALL functions. I hope this helps you.

Jul 31, 2007 | Maytag 24 in. MDBH950AWS Built-in...

3 Answers

Kenmore Dishwasher 665.17979301 - Reset Sequence?


Try pushing the Sani-Rinse and Air Dry buttons back and forth a number of times.

Apr 20, 2007 | Kenmore 24 in. 15142 Built-in Dishwasher

Not finding what you are looking for?
Jackson 24 in. JPX-300H Built-in Dishwasher Logo

Related Topics:

225 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jackson Dishwashers Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3051 Answers

Peter Hampton

Level 2 Expert

193 Answers

Are you a Jackson Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...