Question about Heating & Cooling

1 Answer

I have a honeywell ST699B controller for my central heating & water, i walked past it today and the light that indictes the water is on was illuminated. The water is set to come on once a day but not at that time. Any ideas? your help would be appreciated.

Posted by on

  • philthebade Feb 21, 2009

    I have the same priblem - except botrh the heating and hot water lights are illuminated - bit the boiler is not on. I've removed the front part and it's evident that there has been some overheating on resistors - there are several scorch marks around the PC board. My friend who's a sparky make the comment - 'It's knackered'. I've moved the zone valves to manual - boiler straight away fires up!!

    Solution new timer unit!!


×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have an st699 programmer its set to go on twice a day heating up but when the wife gets up after ive gone to work the timer is not at the correct time so no heating any ideas as new ones expensive to buy

Posted on Mar 04, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Honeywell HZ311 an a red indicator light is on for zone 3, what does that mean if zones 1 & 2 are green ??


red lite for zone 3 means zone three is calling for heat green lite for 1&2 mean zones are satisfied

Jun 12, 2014 | Honeywell Truezone HZ311K Zone Control...

2 Answers

Carrier oil furnace model 58BMA155-20(FORCED HOT AIR)i had changed the blower motor & honeywell st9103a128 fan control board.now the blower motor won't shut off until the breaker is turned off.i...


You need to check the wiring to the limits and safety devices with are in a number of locations, make sure all connections are tight.The most common cause for the blower to run is the high limit device which is the one mounted above the burners on the flat metal panel with two wires.

Nov 03, 2011 | Carrier XHB123D X/Y Series Heat/Cool Air...

1 Answer

I am trying to replace a Honeywell thermostat model #T87F with a model RTH 111, which Honeywell advises is compatible. After following all instructions, I have cooling, but no heat. This is a one zone...


Hi, Have you jumpered Rc and Rh??? I bet you just have the red wire under the Rc terminal only...heat goes on when power goes from Rh to W... the white wire should be on W and energized (24v) when the t-stat is calling for heat...

Here is a list of each common terminal and what their commonly used for. Alsolisted is what colors are commonly used. NEVER ASSUME these are what youhave. Verify all your wires by following each to each piece of equipment. Thiswill help you to be able to match your equipment with the terminal.

Here is the rest of the tip that I wrote...

Thermostat Wiring and Terminal Designations
heatman101

Aug 23, 2011 | Honeywell Heating & Cooling

1 Answer

Do you have a manual showing the display panel controls and operating functions for a Honeywell central heating wall mounted control panel?


Hello. thanks for choosing Fixya! please get back on with the make and model number of your device and we should be able to locate the manual for you. OR go to honelwell.com and search the site yourself. Joe

4 thumbs up please. ty

Oct 21, 2010 | Heating & Cooling

1 Answer

What does the lever do on the end of a Honeywell central heating valve v4043 series?


Hello, It is MANUAL overide function which will allow you to open the valve with out power (mainly for service & testing).

Sep 24, 2010 | Heating & Cooling

2 Answers

Central heat does not blow hot air, just warm air weakly


Sounds like some of the elements are not working. You being in Florida they may not have put very many elements in. It was 61 degrees last week. I know because I'm a Dolphin Fan. You will need a current sensing meter to check the elements.

Jan 04, 2010 | Heating & Cooling

1 Answer

I put in a new honeywell thermastat my heat works but not my central air no power at all. when I turn it to cool will not even turn on air


What da ya got electric heat or gas heat? Did you buy the correct base for the thermostat? Who connected it? Honeywell is awesome but you need a pro to hook that sucka up.

Jun 25, 2009 | Weather King 10AJA2501AH Air Conditioner

1 Answer

My central heating system comprises a worcester bosch system boiler and honeywell smartfit controls. The problem I am having is that the central heating doesn't seem to knock off at the preset temperature...


You could possibly have an ignition problem. The controller will go into a lock-out condition if flame is not established. Turning the temperature control down and then back up may be serving to reset the control system so it tries again.

May 21, 2008 | Honeywell Heating & Cooling

Not finding what you are looking for?
Heating & Cooling Logo

Related Topics:

242 people viewed this question

Ask a Question

Usually answered in minutes!

Top Heating & Cooling Experts

paulcarew

Level 3 Expert

2046 Answers

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

Cris Sparks
Cris Sparks

Level 2 Expert

338 Answers

Are you a Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...