Question about Envision H170L Monitor

1 Answer

Envision EN 5100 E with Dell Inspiron 530...

The monitor will work for a while. It will stay on for hours at the desktop, but when I open a file to work, the monitor will show "Input Not Supported" with black on the rest of the monitor. I have to reboot to get back to desktop. It will work again for a while before I get the message again.

Tried the Dell with another Envision H170L monitor and the message in the middle of the screen is "Out of Range" and the screen gets fuzzy.
What could be going on? I'm ready to return that Dell.
Thanks,
Lisa

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 119 Answers

You can try to reset your display settings... try 640x480 resolution 60Hz refresh rate this can be done in the control panel under display---settings tab..

good luck.if that doesn't work I would just return it and buy a viewsonic LCD here the price was just marked down from $260 to $130 bucks

Posted on Jan 19, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I open the Envision H170 Monitor? I un screwed all the nails but it still wont open.


You will need thin flat blade screw driver to crack open the case, starting at the bottom edge, some of the monitors have very tight fitting so it will take quite a bit of works. You can search YOUTUBE under 'how to open LCD monitors'. Make sure the base is also removed.
http://s807.photobucket.com/home/budm/allalbums
http://en.wikipedia.org/wiki/Capacitor_plague
http://www.badcaps.net

Jun 02, 2010 | Envision H170L Monitor

1 Answer

E228WFP display disappears Posted by


disconnect all the cable from the monitor except the power cable .
see if you see any test screen and keep it on ,if the test screen blacks out you monitor is bad ,better buy a new one as usually repairs cud be expensive

Apr 17, 2010 | Dell E228WFP LCD Monitor

1 Answer

I have a Envision EN-7100e monitor. Downloaded


catamount309, This is only a guess, but unit may have internal "switch-mode-power-supply"/"CCFL inverter" board problem. When screen goes BLACK, is it also BLANK? If you can see WIN-desktop with aid of bright flashlight 1 inch from screen, then SMPS is in partial shutdown mode. If you see nothing, then SMPS is in full shutdown. In either case, Technician will need to repair the SMPS/CCFL inverter board. If KNOWN GOOD monitor works with PC, then you know 7100e is bad. Do you know and understand how the new energy efficient screw-in curlie-Q light bulbs work? If the "electronic ballast circuit" not working, then it can't light-up the CCFL tubes on the reverse side of LCD panel then you see black. Do more reading in my fixya profile for more options open to you. Do your research first!! Hey, reading is free!!!
Will you fix or trade for new? 12fixlouie

Mar 07, 2010 | Envision EN-7100e 17" Flat Panel LCD...

1 Answer

Planar Monitor Wont stay on


Okay.... If you can. install your drive. It may work. If not then your Hardware in your monitor is screwed. Or maybe something else but not to my knowledge.
good luck!

Jul 14, 2009 | Planar PE191M 19" Flat Panel LCD Monitor

1 Answer

Key strokes to get desktop image to external monitor?


Press the FCTN key (lower left), then one of the top function keys. All laptop are fifferent and it depends on model. Dell is FCTN +F8, Gateway is FCTN + F7

Good Luck

Feb 01, 2009 | Envision EN-7100e 17" Flat Panel LCD...

2 Answers

Envision LCD EN-7100e Monitor "Input not supported


Either your display card is not supporting the LCD resolution.

Apr 23, 2008 | Envision EN-7100e 17" Flat Panel LCD...

1 Answer

Envision EN 7100si LCD 17" flat screen


First try auto-adjust with the auto button on the screen
if not worked

Make sure she installed the envision driver. I jus saw it's a discontinued product. Also this product has a maximum resolution of 1280 x 1024.

If installed check her resolution. Right mouse click on desktop>properties>screen. Try alternate resolutions and see what happens but don't set it higher then 1280 x 1024 if possible.

Nov 28, 2007 | Envision EN-7100e 17" Flat Panel LCD...

Not finding what you are looking for?
Envision H170L Monitor Logo

146 people viewed this question

Ask a Question

Usually answered in minutes!

Top Envision Computers & Internet Experts

Steve

Level 3 Expert

3287 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Andrew Taylor
Andrew Taylor

Level 3 Expert

12143 Answers

Are you an Envision Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...