How do you get this machine to drain water better?

Hey Rich,
Error Code E11 means that your Washing machine has detected an overfill of water - over filling with water

• Check drain pump for blockage or obstruction
• Check drain hose for blockage or obstruction
• Check drain pump
• Check fill valve is not jammed open or leaking
• Check electronic control module

Good Luck
JP

Hi.when water is not draining,there must be problem with the drain hose.There must be debris that blocks the flow of water..try to check at the back panel.connecting the drain hose.there might be some pieces of metal that blocks the flow of the discharge water..Better check.Hope this helps.

pump is clogged

Hi, yes you can, but make sure bucket is big enough to fetch all water from machine, always keep hose same level with water in tub, when machine is in operation. lowering hose to floor could get water out by gravity. it's better to put drain hose in sinks, or some form of plumbing, work machine, don't let machine work you, but if it's more convenient for you to drain in bucket, sure, it's o.k. good luck.

Pump is blocked or shot

Pressure switch made telling the machine it is full of water hence no spin.

Drop hose into bucket to drain the water off and the machine should spin, you may be better dragging the washer to an outside door and let all of the water run away at once .

Make sure that the drain hose is unclipped from the back of the machine so that the bottom of the hose is as low as you can get it

Hi, Does this washer have to pump the water up into a drain? If it is possible, it would be better for the machine if you can bring the drin pipe closer to the washer. I know it is not always a possibilty. The longer the drain hose, the harder it is on the washer and sometimes the cloths don't spin out as dry as they will with a short drain hose.

Vic

You need to unplug the machine, and drain the water from the drain hose, accessing the drain pump.

Once you access the drain pump also remove all obstructions in drain lines, this often fix teh problem.

If you do not have done anything similar before, then it is better to call the technician.

E5E  IS FOR  Communication problem. THERE IS 100 %WIRE SHORTING SOMEWHERE.PLEASE CHECK OUT.
ALSO OTHER ERRORS Error code - Fault condition
E11 Fill time too long.
E13 Water leak in tub or air leak in air bell.
E14 Reed switch.
E21 Water not pumping out fast enough.
E23 Drain pump relay on control board failed.
E24 Drain pump relay on control board failed.
E31 Better models. Pressure sensor not communicating with control board.
E35 Better models. Pressure sensor indicates water overfill.
E41 Control board thinks the door switch is open.
E42 Door remains locked after cycle is completed.
E43 Control board problem. 
E44 Control board problem. 
E45 Control board problem. 
E46 Control board problem.
E47 Board thinks the door PTC circuit is open in spin.
E48 Board thinks the door PTC circuit is closed.
E52 Bad signal from tacho generator.
E55 Motor overheating.
E56 High motor current.
E57 High current on inverter.
E58 High current on motor phase.
E59 No tacho signal for 3 seconds.
E5A High temperature on heat sink.
E5B High temperature on heat sink.
E5C High temperature on heat sink.
E5D Communication problem.
E5E Communication problem.
E5F Communication problem.
E67 Input voltage on microprocessor incorrect.
E75 Better models only. Water temperature sensor circuit.
E76 Better model only. NTC temperature for the cold water valve over the limits.
E95 Communication error.
EB1 Incoming power frequency out of limits.
EB2 Incoming line voltage above 130 VAC.
EB3 Incoming line voltage below 90 VAC.
EF1 Clogged drain pump.
EF2 To much soap.

You can seal the cap by some tape, but it is better to get a good replacement, for the filter needs periodic maintenance. Your machine will not drain well if the filter is clogged.

more than likely that it is blocked pull the washer clear so you can see the back get your outlet hose and place into a bucket and see if the water comes out if it doesnt than pump/pipe blocked better off taking washer outside because when you release the outlet pipe from your pump thert will be alot of water that will come out if it comes out of the pump than your pipe will be blocked m8