Question about Maytag Bravos MTW6600T Top Load Washer

2 Answers

I have the MTW6700TQ Bravos washer and it's leaking from the drain pump assembly. I have already removed it and cleared the nickel from it (not sure how a nickel can even make it to the pump!!) and checked the hoses. We also checked the hoses and circulation pump because initially it appeared to also be leaking. Now just the drain pump is leaking. What else do we check? Or do we have to replace the drain pump?

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Maytag Master
  • 18,060 Answers

Drain pump is over 100 dollars. Look for signs the foreign object wore through the housing or cracked it.

Posted on Jul 25, 2017

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Maytag Master
  • 53,745 Answers

Revisit the drain pump and make sure that you have the small "O" ring seal properly installed between the housings
otherwise replace the pump assembly

Posted on Jul 25, 2017

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 50 Answers

SOURCE: My Maytoag Bravos Top load washer drains really

Is the drain hose kinked or clogged? Is the drain hose installed properly? look in the installation Instructions, Press POWER/CANCEL to clear display........ hope this helps.....

Posted on Jan 08, 2010

EMSRSERVICEG
  • 426 Answers

SOURCE: How do you replace the door latch on a top loading

IS THIS UNIT NEW YOU MITE WANT TO HAVE SOME FROM SERVICE DO THIS

Posted on Dec 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Kemore washer stopped working and had a fault code of F 21 I check the large object filter and cleared it out still coming up with F21. What else do I check??


The F21 error code indicates a long drain time on this type of washer. The door will not unlock if the washer control detects that water is still in the tub. To manually unlock the washer door, take these steps:

  1. Unplug the washer to completely disconnect electrical power.
  2. Remove the bottom front service panel as shown in the first image below.
  3. Carefully reach up through the bottom opening and pull the release tab on the bottom of the door lock assembly until it clicks. NOTE: Internal metal edges in the washer can be sharp. Protective gloves are recommended for this procedure.
By pulling the manual release tab on the door lock assembly, you should be able to get the washer door open.

After opening the door and removing the clothes, I recommend emptying any remaining water in the tub with a wet/dry vacuum (or bail it out). Since you already have the bottom front service panel off and the washer unplugged, you can arrange shallow pans and towels to catch any remaining water and pull the large item filter out of the drain pump assembly as shown in the second image below. You may find a clog in this area that is preventing your washer from draining properly. Clear any clog or debris from this area and reassemble the washer. Check your drain hose for a kink or clog. Check the washer house drain for a clog or restriction. Test the washer to see if it will drain properly.

Other issues that can cause this problem include:

  • Not using HE (High Efficiency) detergent
  • Using too much regular or HE detergent
These issues can cause oversudsing in the washer. The drain pump will not able to pump out suds. Make sure that you are only using the appropriate amount of HE detergent in the washer. If you have a water softener, you may need as little as a tablespoon of HE detergent.

Apr 17, 2012 | Kenmore Washing Machines

1 Answer

Ld signal won't drain


For the LD error please check for the following:


  • Check for kinked or clogged Drain Hose: Remove any obstructions in the drain hose / stand pipe / utility sink. Straighten the hose to remove any kinks. If the washer is unable to drain due to a kinked or restricted drain hose, the washer may not spin.
  • Check for Standpipe higher than 8 feet above the floor:The pump is not powerful enough to pump water to heights greater than 8ft. The water will remain in the basket.
  • Check for excessive suds in the washer: Drain pumps cannot drain suds out of the washer.
To clear the suds condition: Check the drain hose and make sure the hose is not plugged or kinked Press pause/cancel twice to clear the display Run the machine through a Rinse/Spin cycle using cold water, then a Normal cycle using cold water.

Note: Do NOT add any additional detergent. This will remove much of the remaining detergent held in the fabric. This step may have to be repeated to remove all the detergent.

Jan 16, 2011 | Maytag Bravos MTW6600T Top Load Washer

1 Answer

Washer wont spin out displays 5d code


Hi,

Remove any kinks in the drain hose. Ensure that the washer is not sitting on the hose.

Inspect the household drain. Remove clogs, if possible. Call a plumber if you cannot remove the clogs.

Check the drain and make sure there is an air gap between the hose and drain. An air gap is necessary to prevent the drain hose from siphoning water.

Clean the pump filter. Open the pump access door. Turn the pump filter counter-clockwise and remove it. Remove dirt and debris. Replace the filter and close the pump access door.

Rearrange the clothing in the load. An unbalanced load can prevent the washer from spinning or draining.

Allow the washer to cool down for two hours. If the washer overheats, it will stop the motor and cool down before restarting.

Close the door completely. The washer will not operate if the door is not securely closed.

I hope the above helps.

Good luck.

Jan 11, 2011 | Maytag Bravos MTW6600T Top Load Washer

1 Answer

My Maytag Bravos quiet series 300 washing machine stopped. Won't drain. A message Ld shows. Not sure what to do


Hi and welcome to FixYa, I am Kelly.
My response is very long and will be in 2 parts this is PART 1

Here is what the service manual says about Ld:

"Ld" (Washer is taking too long to drain

water from the wash tub)

Check the following:

Is the drain hose kinked or clogged?

Is the drain hose installed properly? See

"Connect the Drain Hose," page 2-5. Press
PAUSE/CANCEL to clear display
Also:

Is the drain hose clogged, or the end of

the drain hose more than 96? (244 cm)

above the floor?
See "Drain System," page 2-3.
6. To remove the drain pump: (there are 2 pumps... the drain pump is on the left)

a) Loosen the clamps and pull the inlet

and outlet drain hoses off the pump.

Note that there is a tab on the outlet

connector that fits into a slot in the

hose.

b) Remove the three 5/16? hex-head

screws from the drain pump and remove
the pump from the tub.
Check the pump inlet and the tub outlet for obstructions.
Pump electrical winding resistance test:

-Disconnect the wire connector from the

drain pump terminals.

- Set the ohmmeter to the R x 1 scale.

- Touch the ohmmeter test leads to each

of the drain pump terminals. The meter
should indicate between 10.5 and 14 ?.

----Due to the design of the machine the 2 wires going to the drain pump have be notorous for backing out of the plastic connector. Check the connector of the pump for loose terminal connections. --

From the Ld troubleshooting steps / procedure:

Long Drain

Ld flashes when the water level does not change after the drain pump is on.

• Is the drain hose or the drain pump clogged?

• Is the drain hose height greater than 96? ?

• Is the pressure hose connection from the tub to the machine/motor control pinched or plugged?
• Is the pump running? If not, see TEST #7.

TEST 7

TEST #7 Drain/Recirculation

Perform the following checks if washer fails to drain or recirculate.

1. See Activation of Manual Diagnostic Test

Mode, and perform the Manual: Pumps

test.

2. Remove the console to access the machine/

motor control assembly. See Accessing

& Removing the Electronic Assemblies.

3. Visually check that the P4 connector is

inserted all the way into the machine/motor

control.

If visual check passes, go to step 4.

If visual check fails, reconnect P4 and

repeat step 1.

4. Remove connector P4 from the machine/ motor control and check resistance values of pump motor windings. Resistance values should match those shown in wiring diagram, page 7-1.

If resistance values are good, go to step 7.

If winding measurements are much higher (tens of ohms to infinity) than shown in wiring diagram, a problem

exists in the motor winding or in the connection between the machine/motor

control and the motor. Go to step 5.

5. Tilt machine forward to access the bottom

of the machine and the pumps. See
Figure 1, page 6-13.
6. Check the resistance at the pump motor. Remove the connector at the motor and

take measurements across pump terminals. Measurements should be as shown in the wiring diagram.

If winding measurements are much higher (tens of ohms to infinity) than shown in wiring diagram, replace the

pump motor.

If the resistance at the pump motor is correct, there is an open circuit in the wiring between the motor and the machine/

motor control. Repair or replace the lower wiring harness.

If the pump motor windings and machine/ motor control check OK, repair or replace the pump. Be sure to check

the pump and tub sump for foreign objects before replacing pump.

7. See Activation of Manual Diagnostic Test Mode, and perform the Manual: Pumps test.

8. If the Manual: Pumps test failed, then the machine/motor control has failed:

Unplug the washer or disconnect power.Replace the machine/motor control assembly.
Perform the Manual: Pump test.

Nov 21, 2010 | Maytag Bravos 3.8 Cu. Ft. Washer

2 Answers

Water has started pouring out from under my washer


Hello, you've indicated this problem only arrises during the rinse cycle, is that correct ? The leak doesn't occur during the wash cycle initial fill level ? I want to distinguish the difference because there has been a repair tip issued by whirlpool for the duet and sport washer's. This may be applicable to your machine. If it is indeed only during the rinse, the problem is within the door assembly. Specifically the glass and it's "seat" to the frame. Let me know, I'll watch for your reply. macmarkus :)

Mar 14, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Maytag neptune front load washing machine will not fully discharge water after the rinse cycle...HELP???


Check the drain hose and clear it from any debris that might be blocking the water from draining out completely. If the drain hose is clear of debris, check and clean the pump. Disconnect the machine from the power outlet before servicing for safety purposes.

Remove the rear access panel to access the pump and disconnect the wiring harness from the terminals of the drain pump and the pressure switch.

Loosen the clamps holding the drain hose and the tub hose to the pump assembly. It is a good idea to spread a towel under the pump before loosening the clamps.

Remove the hoses and rotate the pump assembly counterclockwise to release the pump assembly support legs from the keyed slot in the base of the washer. Remove the pump assembly from the washer.

Clear the pump impeller from any debris that might be causing it to work improperly. Clean the tub and the drain hose.

Reassemble the pump, the hoses, and reconnect the wires to the terminals of the pressure switch and the drain pump. Reinstall the rear access panel and run the machine.

Replace the pump (part #25001052) if water still do not drain out completely.

Remove the plastic bag covering the pressure switch. Press in the locking tabs on the back of the pressure switch and pivot the pressure switch off the pump bracket.

Grasp the pressure switch and lift the nipple of the pressure switch from the pump cap.

Install the pressure switch into the new pump assembly in reverse of the steps above.











Feb 24, 2010 | Maytag Neptune MAH6500A Front Load Washer

1 Answer

I have a maytag bravos washing and it keeps giving me a code of sd but i have never used ne soap other than he soap. i have tried everything. i can run the clean washer mode and it goes fine but when i...


Your code Sd is most likely related to 'slow drain', which can be the pump in the machine or the drain behind it. Check to be sure the drain is clearing quickly enough and if so, have the pump on the washer checked. In the meantime, if you hit cancel and let it sit a bit then hit start, it should take right off and finish the cycle. Hope this helps!

Feb 23, 2010 | Maytag Bravos MTW6600T Top Load Washer

1 Answer

Kenmore HE2 does not drain after first load.


  1. Unplug the washer to completely disconnect electrical power.
  2. Remove the bottom front service panel.
  3. Carefully reach up through the bottom opening and pull the release tab on the bottom of the door lock assembly until it clicks. NOTE: Internal metal edges in the washer can be sharp. Protective gloves are recommended for this procedure.
By pulling the manual release tab on the door lock assembly, you should be able to get the washer door open. After opening the door and removing the clothes, I recommend emptying any remaining water in the tub with a wet/dry vacuum (or bail it out). Since you already have the bottom front service panel off and the washer unplugged, you can arrange shallow pans and towels to catch any remaining water and pull the large item filter out of the drain pump assembly as shown in the second image below. You may find a clog in this area that is preventing your washer from draining properly. Clear any clog or debris from this area and reassemble the washer. Check your drain hose for a kink or clog. Check the washer house drain for a clog or restriction. Test the washer to see if it will drain properly.

Feb 23, 2010 | Kenmore HE2 Plus Front Load Washer

Not finding what you are looking for?
Maytag Bravos MTW6600T Top Load Washer Logo

Related Topics:

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

jimorris77

Level 3 Expert

411 Answers

Sheldon Dedek

Level 3 Expert

909 Answers

Bill Long

Level 3 Expert

603 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...